Видео

I had recorded it, but I had originally misplaced the video. I did find it not long ago, but since it's so old now I never bothered to edit or post it. I do still use the Aoocci and have liked it since I got it.

With a LOT of patience. It's a pain threading that strap through the hole. It can be done though. Probably easier if you have fish line. Cut a short line and tie one end to the strap (not to tight) that is meant to go through the strap holder and feed the other end of the fish line through the hole. Once you feed it through, untie the line and secure the strap to the radio.

Should only blink blue and not blue/green after powering the speakers on by holding the power button for 3 seconds. Try doing a factory reset or a hard reset, then power it on and see if the lights blink.

Fuse? There's no fuse in the extruder that I'm aware of.

Try updating your firmware in the AAwireless.

I didn't notice any setting like that. However, my vehicle also has the usb port always being powered and I've noticed that the unit is actually off when I get into my truck. So I'm guessing it does shut off after a while of being disconnected and comes back on when the vehicle powers back up again.

Personally, I like it. It's many times better than the OEM seat, though I think all the major seat manufacturers will be better than OEM. I've ridden as long as 8 hours (with the exception of 1 stop for fill-up) and i was still doing fine. If you have the opportunity to try it out, or any of the other manufacturers, on another bike first, I would do that. Each manufacturer cuts their seats differently so what fits me great, may not be so good for others. With that said, I wouldn't go back to OEM. The biggest reason I went with Sargent was that I didn't have to send them my old seat and they had options with the heated panels built into the seat. The reason I didn't want to send my old seat was mainly because I didn't want to be without my bike while I waited for them to retrofit the OEM seat with the new cushions. At the time of my purchase, I believe Sargent was the only one that didn't require the OEM seat to be sent to them.

It's not required, it's recommended. Otherwise, once the battery is dead, you have to remove it and recharge the battery. During that time, the lock will have no battery power and will be unusable, with the exception of using the key. It takes many hours to fully charge these batteries.

No. The battery has a usb c port for charging. So any phone charger with usb c cable will charge your battery.

Same day. As soon as the fridge was set up, they immediately loaded the old one and took it with them.

some of the screws have locktite on it, which gives it some resistance when trying to remove it for the first time. As long as it's not rusted or frozen in place, it should come out with a little effort.

Thanks! Unfortunately I don't remember the name brand of the crash bars anymore. I had bought them directly from my local BMW dealership though. I had recorded the install of the crash bars, but sadly my camera battery died and I didn't notice until I had already completed and put everything back together again. :( Going by the pictures on the websites, my crash bars do not appear to be any of the following brands: R&G, Wonderlich, TouraTech, or Iliumworks. If that helps any.

As long as the connections on the back of the monitor match up to what your mac can connect to, then it should work fine with it. Monitors are not usually platform specific unless you're dealing with a niche product.

No, I don't have any white noise in my recordings, either on the video or local recordings...

Another person mentioned he was getting static, and after he swapped out the usb cable for a different one, the static went away. You might want to try a different cable and see if that helps.

Thank you for replying

It comes with a usb c to usb c cable for android and usb c to lightening cable for ios phones.

Glad it helped

I actually haven't had the need to use the local recording so I never compared the two. I did test and check and yes, my local recording does seem to be lower in volume compared to what's saved with the video.

@@R-TechEnthusiast Thanks for checking! Another point that could be good to know for users of people considering a buy; I'm happy with the mic and think the sound quality is ok (maybe not always great but good enough) but the included cables are of quite bad quality, stiff, and feel cheap. I had severe issues with static when filming with my Iphone and was very close to returning them but fortunately tested to swap the included cable between the receiver and Iphone since I had one of those cables and the issue went away completely. I could even feel a difference in connecting the cable to the receiver, the fit from the included one felt loose while the other one I hand felt snug och tight.

They are actually pretty convenient if you find one that works. After I got rid of this one and switched to another company, I've enjoyed using it, and now I like having it.

Cd quality - 48KHz, 16 bit stereo

I usually let new devices charge overnight.

This video I didn't edit the audio. I have had to edit it before, though. I noticed the mic is more sensitive than my previous mics, so I'm becoming more aware of where I place the mic depending on my surroundings. Mic placement has helped with reducing the need for audio editing or the amount of editing. If I need to edit the audio, I usually use the audio editor that comes with DaVinci Resolve. A few times, I have also used Audacity for audio editing.

Not much you can do other than making sure the power source is good. You pretty much have to contact tech support.

I sure hope the new mic sounds better. Hehe. I definitely like it better than the old mic I had.

Nope, on this model, you can't. I have no clue about the latest models, though, probably not, though.

Only if it came with it. I didn't actually look. Hehe. The S330 has been mostly flawless, so I wasn't really concerned about it with this one.

You're welcome! Hope it was helpful.

I love curved displays for large monitors. For flat screens, I prefer smallish monitors (under 30") and just placing them side by side instead of using one large flat monitor. I usually just have 2-3 flat panels side by side.

Hope the monitor works out for you. I actually have 2 other LG flat screen monitors that I was using for video post-processing, and they both worked great for that purpose. I also recently got a super large Samsung monitor that I haven't posted a video of yet since I'm on vacation at the moment. I was using it a month or two before I left and have really liked using it. It's just very large. That one has a massive curve to it, and it was being used for video post-processing and gaming. I had no real gripes with this monitor other than not noticing it was flat vs. curved, which was partially my fault for not looking at the pictures more clearly. One thing I do like about LG is their monitors. They never have never let me down (unlike some of their other products *cough* *speakers*), and some of their monitors have great color reproduction and are factory color calibrated.

While it has held up. However, since the top material is made of VERY stretchable material, if I step on anything that's not flat, my foot will literally slide off the sole, which causes me to step and put pressure on the edge of my foot instead of the bottom of my foot. I've almost twisted my ankle a few times because of that. As long as I'm walking on a paved surface I like it, but I won't walk on any uneven terrain with these shoes, just not safe. If I'm going to make a quick trip to the store and I'm in a hurry and don't want to deal with laces, then I'll quickly slip these on. Any other situation, I mostly won't wear these. Which sucks because I actually liked the feel of the shoes.

So true. They just seemed like a good mic to buy and give a try at the time. Hehe

Glad it was helpful!

I hate to admit it, but I've only used single TX recording so far, so I haven't seen how stereo/ dual TX recordings are saved. From my understanding, mono is for single TX and stereo is for dual TX. All my recordings have been indoors, so I haven't had to use the gain increase/decrease yet too. I'm actually at the airport right now on my way to Asia, so I am not able to do a quick test of it. Sorry.

I have noticed the mics are fairly sensitive. Depending on the location of recording, the audio can either sound good or have bad reverb (hollow sounding effect). I've been trying to experiment with placing the mic on different areas around me depending on where I'm recording.

You will need to 3d print a new mount for the 3dp module, there are quite a few designs on Thingiverse. There's what looks like a silver disk on top of the module with 2 super tiny screws. You'll remove that part and replace it with the 3d printed part. Then you'll need to buy the Pneumatic Fittings (the brass and blue part) as well as a bowden tube for it. The fitting will screw into the part you printed out.

I got it off of Thingiverse. I found quite a few on there, but the one I ended up going with was this one: www.thingiverse.com/thing:4763024

Surprisingly enough, it does not state it on the bottle.

Hi! It has a flat bottom on it so it is possible to stand up on it's own. I currently have it standing up with nothing in it and the main compartment wide open. If you pack it properly so the weight is distributed correctly, or on the bottom, then it will stand up on it's own with no problems. I took it with me on a trek through some woods and when i set it down, it stayed up just fine.

thanks man!!@@R-TechEnthusiast

@@alexanderlim81 you're welcome 😊

Happy it helped!

You're welcome. Glad it was helpful!

I got rid of it and switched to Smart-Box, which is now Aoocci. Haven't regretted it once.

I have the dual extruder. I haven't really had any issues with it, although I don't do a massive amount of printing either. The only real issue I had with it ended up being caused by my dry box not feeding the filament smoothly, it had too much friction and wouldn't let the roll turn smoothly. That caused my dual extruder head to get pulled "up" and end up printing in the air. When I removed the dry box, it printed properly. That's the only real issue I've had with the dual extruder, which ended up being due to Sunlu's S2 dry box.

How do you do that with a multimeter? Do you have a video where I can see how this is done? Thanks!

I actually haven't tried recording long sessions locally, but I'll give it a try and see what happens. I'm on Babson at the moment, and I didn't bring it with me, but when I get home I'll test it. Yea, in my PC, I just plugged it in, and Windows immediately saw it and assigned it a drive letter. The audio files are in the root folder for the transmitter.

*I'm on vacation. Stupid auto correct...

@@R-TechEnthusiast Thank you in advance. Have a nice vacation

So I tested it with an ~3 hour recording. What it is doing is recording for just slightly over 30 minutes (31 minutes 20 seconds), then it ends that file and starts a new file where it continues the recording. So my ~3 hour recording ended up with 6 separate recorded files.

@@R-TechEnthusiast no gaps in audio in between files?

Nice to see it at least works for some people.

Yea, i eventually figured that out. Hehe thanks.