Видео

Robinson Larry Hernandez Matthew Hernandez Timothy

Just one slight modification to your method, if the boot keeps coming off, secure the front part with a zip tie, this prevents the dust cover from sliding off and allows you to extend the cover further back for easier installation and just open up the zip tie when done. Great vid thanks.

Incredible piece of work. Not for the average consumer.😮😥

Martin Sandra Johnson Cynthia Taylor Susan

Thank you for this video Mend it Man. Ive been rebuilding a yamaha ybr 125 and turning into a cafe racer. This video gave me all the knowledge I needed to swap out my sleeve and time my engine proper.

Thank you very much.

Question gvc160 and gvc 190 are the same size crank shaft?

Fit a grease nipple if theres clearance on cover

Excellent clear demonstration , Many thanks!

Well done, interesting watch, I shall use something like this to remove my engine mounts.

Hi mate watched you for a while. It just do happens I'd watched this before and actually ended up with the same bike to commute last year. I'm just doing the same job at the moment on it as piston blew. Just wondering is there another way of checking the timing without using that hole on the side of the cover? Thanks 🙂👍

Si seulement j'avais trouvé cette vidéo plus tôt, je n'aurais pas bousillé un joint cache-poussière en voulant l'enfiler dans la gorge intérieure de l'étrier puis de mettre le piston après en espérant que la lèvre du joint passerait entre les deux. En tout cas, merci pour cette belle vidéo très précise.

Excellent video and a great help. Thanks! 😀

I’m pretty sure they’re supposed to be an O-ring on that black cylinder. When you took it apart, you noted that you found a piece of one and you showed it to the camera, but then it didn’t show you replacing it.

Is there something more modern I can upgrade it to? Also an upgrade to get rid of the distributor? 1983 polo

Could I replace it with something more modern

Extremely helpful. Doing this tomorrow!

Amazing! 🎉 Big thank you for this pro tip! Wish you successful repairs! Have a good one!

Are we all ignoring the metal ring?

Thanks much.

Hello Sir can you tell me where you got your extractor, did you make it or you bought it, thank you for your answer.

What type of Honda seal did you use.. Do you have a serial or part number? Thanks

Never had to replace a carb on a stihl product. Wonder why it failed. It's the echos that have garbage carbs

you need a new filter as well by the look of that one. would make a difference. i had one of these years ago. an A reg. bought brand new. loved it. great little cars. never let me down.

I changed the pump on my mini r50 but the steering is still a little bit stiff like it was b4, what seems to be the problem ? Do I need to change the whole steering rack?

Great ❤ My question I have same machie over heating I need reason for this issue

Thank you for saving so much time :)

Thanks for video. Really works.

3:25 That's the idle cut off valve, it didn't made any difference? Mine is broken. Had so many shit with this 1B1/1B3 that I'm already thinking of a replacement of a simpler 36mm singleport carburator, but I have no clue which one. Please, I need some help with this Pierburg 1B, it's for an Opel 13NB Kadett/Astra E and it has all the emmision-valves already. its from 1990. Thanks in forward!

my hrd535 makes a grinding noise when i use my rotostop,the blades dont turn but they wobble slightly. the sound is gone when in engage the blades. i tried removing the middle bolt but its impossible to remove.

Back breaking machine 😢😢

EXCELLENT THX!!!!! Saved 60.00 on Amazon

My speedfight 4 2s goes off when im driving it.. you know if this has smth to do with this?

tq

I couldn't get my dust seals on but after watching your video this task was..... still pretty damn difficult. Mine didn't pop in anything like as easily as yours but got there in the end. (As far as I can tell.... haven't put it back on the car yet....) Thanks for making the video.

Looks amazing mate, well done!

Great video and information! Thanks!

Looking at this after I realize my vehicle has missing hoses my plastic T piece on the vehicles side of the filter is blanked off both sides for some reason. I bought this sprinter not too long ago. any idea what the two hose pipes that's connected to the T piece is comming from?

So, you just used sandpaper and sanded the cylinder? LOL

bro a pickle fork next time like 2 hits and it seperates

V helpful video. Cheers

Glad you noticed that alot of people do not and blame the bolt when the life has been strangled out of it in the hopes of it sealing!!! Also the nozzle tapers off so a new washer cannot stay central it has to be stuck with grease - finally its that black death getting down the bolt hole preventing proper torque down - resulting in compressed carbon, a hole through the water jacket and a jacked out thread 😮😮😮😢

What grease are you using on the seal and on the piston to put it together good video will be doing mine soon.

Hey thanks for the videos I am going same route, so helps a lot to see someone else before I am in the deep of it 😉 the part that goes deeper into the sump, what car or model did you get it from?

When I get a dodgy tick over I mostly find it is a dirty air cleaner.

Is it possible to pull the piston out by hand?

Hi Man! :) , i 'm about to decide between a yamaha neos 4 or a peugeot speedfight, both are liquid cooled 50 cc versions. Which one would you advice me to prefer among the 2? and why. Thanks for the feedback in advance