Видео

Break it loose then use rubber hose that fits snug on plug twist on out or start back in

Your video was a big g help. Thanks

What are the torque specs when installing/reinstalling the throttle body?

Thanks, toothpicks... great idea

13 mm and 1/2 inch are so close it’s not a secret 8mm & 5/16 old school shit

You don't have your mass air flow sensor plugged in lol

Came out a little bit tough!!! Ya right.. this was the hardest alternator change I have ever done. Give me a GM over this any day'...

Thanks very much. There is 0 information for a 2015 Challenger expansion valve on the WWW. This was exactly same as mine.

Do I need to disconnect the battery before I start? I want to finally tackle this project for my wheelchair van ♿️

Good afternoon. Why did you change this part? I have a high pressure in the return line of the air conditioner. There should be low pressure in that line and I have high pressure there. So I need to change this part too? Thank you.

I followed the steps and made sure the new cable was perfectly installed. Reinstalled the console and no change. Monitor is still blank, but able to access menu as before. Could it be a cable behind the dashboard?

Thank you for your help

I did the throttle body cleaning today. Hopefully it helps some. It was just as dirty as yours. Thanks for the video. It made the job very simple.

Ok. I replaced the computer on hers about a year ago. It ran fine for a while and then started acting up again. It stalls occasionally, idles rough, stumbles while going down the road. Occasionally trouble cranking.

I'm curious if cleaning the throttle body fixed the stalling issue. I'm having trouble with my wife's Hemi.

Would an alternator throw U1110 code and turn on your ABS and TCS lights. My volatge was at 10 too.

Thank you, was worried the fuse bank had to come out.

Wish you showed how to get belt off🫠

So did it fix the high idle.

Very poorly done. Didn't you even view the vid before you uploaded it? Thumbs down.

If your here you didnt give up on your chrysler

Nice. Thank you.

I have 2008 chrysler 300c keeps killing batteries, wont go over 30 miles per hour with new battery.

I appreciate this video so much. When I saw where my alternator was I almost panicked at the idea of needing to take it to a mechanic. You are about to save me so much money!

Is it better to buy a new or refurbished?

Cool, Thanks. Not a MOPAR Guy and needed some direction.

Very helpful thank you

Thank you for taking the time to put this video together. Super helpful and I was able to fix the issue on my 2016 T&C!

Very helpful, thank you!

Do you have any idea on how to take the dash out because I am looking for a wire harness because my code reader doesn’t work and other stuff like my key doesn’t turn the ignition off my passenger door open it turned it turns the truck off

Is there a way to make sure you get the correct ribbon cable without taking the whole top panel out? I keep seeing to make sure you have the correct part number, but haven’t been able to verify an easy way to know what cable to order as there are two different ones.

Thanks for this video, very helpful. I'm not sure if I have the wrong bulb or not but I have the H-13 bulbs. My issue is the headlights are very dim, almost like they're (DRL)'s daytime running lights. When I hit my high beams then they seem like normal headlights... No one flashes their high beams at me so my question is, what was the headlight bulb # you used? My soul does not have (DRL)'s so I definitely think it's a bulb issue...🤷🏼‍♂️

Where do you get the replacement strips?

The bleeder screw on the front of mine is bone dry I hear a squeal when I cold start I’m guessing water pump being that it’s dry but what could be causing the pump to not get coolant in that area because the hose and rad have fluid in them but nothing in the front of the water pump housing, I’ve been having issues with it getting hot the. Cooling down getting hot then cooling Down originally had a leak and used k seal fixed the leak I think but then the overheating issues started, hasn’t overheated but it gets hotter than it’s supposed to I think I’ve seen it get up to as high as 242 then shoot back down to 195-197

Ha! And there it is!! I commented just a few minutes ago on a previous video I just saw, and decided to dive into your channel to see if you had uploaded the penetrating oil. Brings back memories!

Ive seen this demo before, and I’ve done it. Back in about 2011-2012 or so… Those bits are legit. I bought the set up to 1/2”, and it had a decent three drawer box. I never burned one up. And most of them from 1/16” or 1/8” (can’t remember how small they went) up to I wanna say around 3/8” had multiples in case you’re an idiot, and did manage to somehow break, or burn one up… Now you mentioned in the beginning of the video that you were going to show off the penetrating oil as well I believe, but we didn’t get to see it lol… I can attest to that as well if it’s the same formulation that I used… It was KM penetrating oil is all I remember, and it smelled like freaking CAKE BATTER. I swear on my life. I’ve still to this day never used better, and I’m in industrial maintenance… Blaster, Kroil, Knocker Loose, WD, Amsoil, DuPont; NOTHING came even remotely close to that cake batter. Thanks for posting buddy!

I love this recipe. Have cooked it many times. 😊 Ty !!! 💛

That one in the driver side is a son of gun

118 ft pnds for the axle nut that way you don't risk over tightening and causing problems with the wheel bearing assembly.

Thank you so much fixed my wife's van 👍

Probably would have used a headlight restore kit while they were out of the car. I need to restore my wife's (they've gotten milky like yours) but I think I'll just mask off and rework them in place.

Heaven sent 🙏🏾

For those that have cars that stall after a fill and then the car turn back on later...there's a free gas tank replacement the dealers won't tell you about. I pressed them and they changed my 2006 300C's gas tank for free for this issue. Here's a link to another owner who has the official letter for getting this repaired. ruclips.net/video/pD_zJeOZxew/видео.html

A have a 1999 too thank you I will clean it tomorrow

My truck is manual too I can find the correct piece , so how cancel the ítems for the transmission automatic you can tell me please !

Got the same P0016 code. Just bought the sensor. If it’s that simple 10mm socket shoot I can do it myself. Just need to go borrow the tool to do it. Hopefully that will help remedy the issue which was the gears shifting from time to time between 40-60mph..

Thank you so much for making this video. This is exactly what I needed to do in order to get the DVD player to work in my 2016 Town and Country. My four kiddos thank you the most as now they have a DVD player right before our family vacation.

Great video! I broke the screw hole on the carburetor so ended up ordering a new one from Amazon, and since it came with a new air filter and spark plug I went ahead and replaced them also. Bad news: the mower still didn't start. Did you ever solve the Automatic Choke issue? I checked it out and it seemed to be connected OK but I don't know what else could be wrong with the mower.

Thank you for sharing

Just got my first can from my sales rep Chris Matthew's. (Great Guy) I'm super excited to use this product, especially after seeing the demo. I have several Kimball Midwest aerosol products, they have all performed far beyond my expectations. Going to purchase the cobalt drill index and die grinders soon.