Видео

Where do you get your numbers from ? Like your condenser split and td ? What is td ?

💯👍👍👍

Where is this bin switch?

👍👍👍🤙

👍👍👍🤙

Good content. Hope to see more.

I don’t do any refrigeration work but on a 404a ice maker machine… what would the pressures be? I know ambient temp and other variables determine that just like residential hvac pressures but like a rule of thumb?

What was total troubleshooting and repair time?

Wow man I can’t thank you enough for creating such a informative and properly detailed guide this is a huge help for me as I have no proper training and these machines are complex as a brand new tech I know this is 4 years old but keep it up for us!!

Man, i guess if youre in buisness for yourself replacing the whole head would be the way, but ive fixed many distributor leaks like this on refrigeration and ac/heatpumps as a tech. Id rather fix the leak and be done in a few hours than leave a customer shit out of luck till we can get a new head. Jmho. To fix leak on the distributor, you need to clean well, use flux, and high heat but quickly targeted at the tube thats leaking. Oxy acetylene with a small tip is best but ive also done it many times with a turbo torch with a bit bigger tip as well years ago. That leak can always be repaired from my experience.

How long does it take to make ice?

How do you upgrade the software? Is the software on the USB?

😂

I like this guy a lot

I really appreciate all your videos. You make it seem so easy . Thank you for providing these videos.

$2k for a jug of r22??!! 🤯 wow

The camera is our friend during these situations/change out for wiring

Great video. Can you post the troubleshooting steps. Thanks

Was the problem the dirty condenser coil or water distribution tube was blocked?

Can I use same formula with a TXV?

Amazing videos man! They have helped me temporarily

When does condenser split use 30° instead of 15°. Thanks in advance

When brazing txv , do you use 15% or 45 ? If you use 45% , can you unsweat a 15 % brazed joint and then come back to braze it w 45%

please keep making videos on true and igloo brands commercial

Hey can you please tell me where i can buy parts for commercial refrigeration fridges

Have an SH1G/AB, pilot lights, spark stops 24v to MV and no main flame, pilot dies and lose 24 volts due to no pilot. This will cycle forever. So looks like I am getting flame rectification because spark will stop as soon as main valve is energized, then it all drops out. Customer has an identical unit that is no longer in use due to door damage and kept this for parts. So I have replaced pilot assembly, gas valve, Fenwal board, even 1000 ohm resistor temp sensor, ensured centrifugal switch closes. Still can’t get it to go to main flame. Would appreciate your insight on this.

Where can I get the tool to check the solenoid is engaged ?

Well done man

2:44 - I’ve seen different numbers thrown around all over utube among HVAC/R techs. Is there a place I can find these numbers written? The numbers I see floating about are Condenser split: 20, 25, and now 30; Evap split 8, 10, 15, etc.

Place your hand over the exhaust, it will heat and stop if the flame sensor is dirty even before you take the cover off the control cabinet.

Where are you getting the 10/15F is that your superheat target number???

Thanks for these videos. You make refrigeration so much easier to understand

Ya but what caused the safety shut off

I am a bit confused as to how open contacts and switches are receiving voltage? Should they not be at 0 if they're open and show voltage if closed and contacted? 10:31 for example, how can the switch be open and have voltage, would it not be 0 until contact is made and the switch engages? New to Ref School thanks!

Where did you get the 30F from? And where did you get the -20 from?

i have a question it seems you recovered the system, why not just pump the system down ?

Hi , quick question . what's the condenser split in an outdoor condensing unit?

When you used the P/T chart to get 84 psi does that mean would like the suction line to be at 84? Can you explain why? Ty

At the end of the video where the 22F come from?

Thanks for this videos!! Learn something new every time!

Hey Anthony, I’m the guy Albert is training. I love you your channel, it helps me a lot. Thank you!

More commercials than information

Why does the head pressure have to be at 148f? What math did you do there? I’m new to this trade

Thank you, very good videos How come evaporator is freezing cz of bad compressor starter?

Thanks for a well presented video. About How much did you charge the customer for this job?

I like the excel spread sheet options for what is going wrong or right and you can diagnose the problem that way. It is hard to remember every step or possibility, this is great. Subscribed and saved this vid for future reference.

I’ve isolated mine down to the water pump, but I have no idea how to remove it. It’s the same unit you were working on in this video. do you have a video that shows how to remove that? Can you give me a few tips?

If it hadn't leaked in two years,it ain't the installers fault.

I'll love to tag along with you,just pay for lunch and we're good👍

tq sir for video ..very good infomation🤘🏻