Видео

Gg after market parts

Any advice on getting the upper bell housing bolts off? They’re in there pretty good😅

Viewers didn’t get to see the process of taking the shafts out

My 2009 E-150 with the 4.6 V8 isn’t leaking anything after 100k miles.

There are companies like that but they’re not allowed to sell their vehicles here.

What tool did you use to remove the pins that hold the pads

Ball park how many hours is a job like that?

I have the 5 blinks also. However, the ac system works great until it doesnt. I dont feel that i have a leak. It happens after driving a little while. I wouldn't have cold air at all if it was a leak. Can the ptessure switches be changed without evacuating on these?

Y si Solo quiero cambiar los bulbos!???

Buen video, gracias por compartir.

nice n great video ,do yo u have part number new version sir

How does the carrier thrust bearing go in? Flat side or sliding side first? Which side of the carrier thrust bearing faces the reduction hub?

Can you get my mechanic to do this for me? Jk jk, my truck is a 2011 with 175k, so I might as well just do a full timing chain.

nice work probably can do it myself, but I do not have the lift to get the bed up or the building to do it in,so that being said ,how much do you charge and where are you located?

Hello, i have the same 2017 2.0 EB and does that anywhere from 25 to 45mph. 170k miles. If I step on it you hardly or don't feel it. Cruise at highway speed and its all good. 100% is fluid related? I'm planning a long trip should I do this flush ASAP?

Thanks for an excellent video with clear voice narration

Thanks! Clear video. Making me save a little money from the stearship.. I have to do this to my 2017 Escape.

What’s the cost of this job usually? I’m also in WA if that makes a difference. Thanks!

You should have done the caster bushing and track bar relocate before installing the new springs and shocks.

I have this knock and have been to several mechanics who wont touch my truck. Toyota itself turned my truck around in like 6 hrs and said it needed a new engine for 14,000$ (never checked oil, never drove it, nothing) same sounds as this vid in the same exact place. Im willing to try this fix, but, id like to know what kind of damage this causes if left untreated (as i have) for a while. It began making this noise a few weeks after purchase and has gotten progressively worse. Its in a 2012 tundra in primo shape with some nice upgrades and i dont wanna give it up at 120k. I love this truck, it runs mint, but the tick is SO loud now its driving me crazy. Runs perfectly, never an error code, no smoke, clean oil, just KNOCKS all the time. Cant order at a drive thru, can hear it running from my backyard. only gripe with this truck at all. Also, while in there does it make sense to replace any parts other than the tensioner? Would it make sense while there to just swap all the wear parts? Chain, pulleys, etc? I dont wanna do twice.

'jiffy-tight' just sounds bad lol

Throw some penetrating oil in there let in set, bet you don’t need that big breaker bar.

Did the transmission jack leave any dents on the trans pan?

Got a 1.5L ecoboost also. Just had my engine replaced. But the thing is misfiring at idle only. No check engine light or anything. Could this be a timing issue also?

Pulls out a specialized tool.Bead Buster XB-455 aka $$.$$. Def not a do it yourself video.

Dude, you are just frkn AWESOME! I was searching ways to get my window up and happened on to this video! Nissan's site and customer service is s_it, I've asked them A LOT OF QUESTIONS AND HAVE NEVER GOTTEN A REAL ANSWER FROM THEM, ALL THEY WANT TO DO, IS SLOW-D_CK INTO BUYING PARTS THAT MAY OR MAYNOT FIX THE PROBLEM! ANYHOW, I WAS TINKERING WITH MY ARMADA AGAIN, CHECKING CONNECTIONS ETC.ETC. AND REMEMBER YOU TAPPING ON THR WINDOW MOTOR AND THOUGHT, HEY IT WORKED IN A VIDEO, SO I TOOK A HEAVY WRENCH AND HAMMER AND TAPPED THE MOTOR CASTING A FEW TIMES AND ' WALLLLLA' IT'S WORKING LIKE NEW AGAIN, JUST WANTED TO GIVE YOU AN ADDABOY AND SAY, THANK YOU ! IF YOUR UP TO A CHALLENGE, HOW ABOUT, HELPING ME FIGURE OUT A REALLY AND SMART WAY TO BYPASS YHE O2 SENSORS SO MY VEHICLE WILL PASS SMOG,? I KNOW IT CAN BE DONE, WE ARE SMARTER THAN THE CARS COMPUTER WE ARE THE CARS, WE INVENTED THEM? I OUT SMARTED A FORD'S ,"SMART" CHARGING SYSTEM, AND I'M NOT ALL THAT SMART! BUT NOW I KNOW ONE THING YHATS TRUE, AT LEAST YOU SMARTER THAN A FORD! THNX AGN!

It’s comical… my buddy got aftermarket wheels and tires for his 23’ Raptor it came with aftermarket TPMS sensors. Put the wheels on his truck drove a few miles his truck picked up the new sensors no problem. I buy wheels and tires same tpms sensors my tundra never picked them up. Bought new Toyota TPMS sensors off eBay for a fraction of what the dealer charges I go to the dealer (sensors are already installed) to get them programmed and apparently the scanner can’t just pick up the sensors the scanner needs each one manually put in. They wanted to charge me 4 hours labor @ $150/hr. to program them. Really Toyota? Your vehicles can Bluetooth your phone to the car and give you your phone’s serial number but your scanner can’t read a sensor without a tremendous amount of work?

My Lord ! - " Rain City Wrench " - outta Washington State ( West Coast ) - whatta Cluster Flux Assignment ! Southern California Vietnam Era Veteran Ex GM Dealership Smog Inspector - Smog Repair Tech /Independent Auto Tech.

Nice find

Can’t believe all this crap needed. Would’ve been easier to just pull the engine?

Thank you!!! It was daunting but we got it done thanks to the help of your video.

Finally someone with some brains that showed the whole process..thank you

This job might be better left to a pro...

This made me so glad that we had this factory installed! 😆 I highly recommend it. We use the B&W Companion w/ Slider Fifth Wheel Hitch, which has a pin that drops in & locks to the bed mounted Turnover Gooseneck Hitch. Unlike a lot of 5th Wheel hitches, it doesn't require any additional attachment points, so it's easy to remove (in 2 heavy pieces) & have a clear bed. We're towing a 40' 5th Wheel & the whole system works really well. We will definitely be putting it in any future trucks too.

thank you!

Tractor porn, I love it!

Outstanding work! You sir, have the patience of a Saint!!! lol I see now that Ford has a pan replacement for 2.7 Ecoboost, as the original pan is no longer available. Pan # JT4Z-6675-E, and use only RTV# TA-31 for corners of pan only. One thing about Ford engineers, they make you use every tool in your tool box. lol Thanks for sharing!!! Cheers from Motown/Dearborn.

What size socket, I have a 1.6 ecoboost with the threads in.

Excellent teaching tool! BTW, I intently watched to see him Show the Idiot light Finally off....but he was done & gone..!!! Could He Edit this Video and show that? :)

First of all. My first car is ford escape 2013. I bought a week ago. I buy from used dealerships. And i have a problem. Shifter can move but wont shift. Indicator light stuck at Park position. After look up this video. Is that same problem with my car? Please answer. Cause i have no idea about car. Thank you so much

The engineer over thought it. An insert track on the left side and two screws on the right side and that's it. What the heck.

Can the field coil be bolted to the cover in the correct orientation, wire ran thru the hole, then put the cover on?

This is freaking insane!!!! You have to disassemble the whole car just to change the taillights!!! Thank you for making this video though so I can see that I will be taking this crap to someone else to do for me! 😂

I have a 2019 Raptor and I just replaced the arms and I had to loosen the rear glass panel to get the arm under it and far enough back to reach the hole with enough clearance. Your install seemed to have plenty of room in the rear. Now the motor doesnt seem to have the power to move the new arms back and forth and it keeps stalling/returning. I can get it to close but only if I help the air dam close. Any ideas? It was a major PITA to get the new forward portion of the arms into the track and they were hard to move forward and backward to get the ears to line up.

So if it's blinking five times that means it's low on coolant / freon?

Great video. I just had this installed on my 22 super duty by a Ford dealership near me. When I got home I noticed the castings seem to be slightly off-center in the bed. I measured the position of the gooseball casting from the left and right side of the bed and there is about a 1/4-inch difference when measuring left-to-center compared to right-to-center. My bed seems to be aligned with the cab based on my measurements but the crossmember seems to be slightly crooked. I’m curious if this can be corrected or even matters? I brought it up with the dealership but haven’t received much of a response as of yet.

thanks so much for this video, My BMW X5 f15 has a same SQUEAK noice.

Hi,This is Astra from Roadanvi.We are a brand specializing in car stereos, infotainment systems, and related accessories.I would like to invite you to do an evaluation for us. How should I contact you? Did you receive my email?

I have question about aligment of this plate and conwerter. Is a little off a acceptable thing? I jusat watched wideo about them and guy said " these flex plates are there to make up for this misaligment"

Yikes! Good luck with the volume knob repair. Hope it goes smoothly! We sent you an email, take a look.