Видео

I just ordered a Spal with its harness and a carbon intake, hope it will solve my problem with cooling, I also have another question, do the z3m radiator needs to be original or the aftermarket Nissens version will do the work too?

My car is a 1989 320i e30 with a m50b20 non vanos swap, diesel fan clutch and diesel radiator, yesterday the fan clutch hit the radiator and broke it, now what can i do, what changes to do to so i dont get my radiator broke again? any help please?

Question for you - I just picked up a HF 3-ton Rapid pump (not the low profile one) and it raises fine, but just like your Daytona in the video it settles about 1/2" after reaching the top. That can't possibly be normal - or is it? I'm here because I'm thinking it's a bleeding issue, but maybe you can offer some insight? TIA

Great, now I want a new box...

thank you

I have extensive experience with both of these products. The hardware quality will fail On the Amazon brand. The main shaft that adjusts angle for pulling fenders with strip. And also the there are two screws protruding through the each side keeping it from maxing out. As the Eastwood has flush hardware allowing for it fully recess. It is worth spending the money. I promise

Thank you so much for this video متشکرم

I just ordered one off eBay was looking into the Eastwood one but 130 for the combo pack after shipping compare to $70 for heat n roller *SOLD* wish me luck guys!

Is the eastwood tool made in USA?

i just bought a 95 m3 shell, these videos have been amazing since it came with an s50 to put it but he didn’t label any of the wires and connectors, do you have any diagram or pictures showing what each connector/wire goes to.

Just found this video and ordered the block, thank you. The shorter belt isnt needed for the e30s with the stock m20 engine since the power steering pump runs it own skinny accessory belt correct?

Nooo! You’ll regret this always. I have a small collection of BMW’s. Among them Interlagos blue E46, Technicolor Violet E36 and Imola M Coupe. The Violet is the one that gets the most attention and gets a ton of compliments. Beautiful color.

We need an install video for the door card you guys sell

I dont have powersteering on my e46 racecar. Its a nightmare. Not worth it

Do You make plug & play harnesses for Mercedes ??

I am just swapping a non-power Z4 rack into my 1999 BMW Z3 Coupe.

What made you put that loud music over your voice? I am having trouble discerning what you are saying.

Excellent video

Have the same one as the amazon one, paid 30$ for it. Needed it once on a car with VERY thick quarter panels, with one that was baconed and dented, so it didn't just need to roll the fender I needed to pull it and straighten the damaged parts. It did fine, even when reefing on that handle, only issue I ever had was that lock nut that goes on the end of the jack screw, it got loose twice on me before I tack welded it on. It's a design fault that the eastwood also has, whole jack screw is spinning so obviously it wants to loosen the nut. Should have a cotter pin or something, nylon lock nut doesn't suffice. I would get the nicer one if I had a business or something but for personal use, it's one of those tools that only gets used once every few years on which you can cheap out IMO

Fire vid, I knew it was Florida 3 seconds in, that heat is exhausting to work in so the space will be much better

Smol garage tings 🫶🏽

Out of stock?

Nice. And very cool sound track.

are they also suitable for drifting?

I liked this video a lot, as it showed you could get the toolbox into position by yourself! Were you able to get the hutch on there by yourself, or did you need to use a call a friend lifeline?

Very nice Justin. Keep up the momentum. Looking forward to the content. Yes , time wake up our E30 and Drive it!

Really cool it comes with that ramp to get it off the pallet. Harbor freight with the hookup.

Can’t wait to see the banner

Hell yeah, this is the kind of content we need. Setup looks solid. Always like to hear the updates 💪

Very interesting "warehouse" space. It looks more like a storage unit / RV storage place. Awesome that they let you install a lift in there and I wish I could find something similar by me. It looks like just 1 power outlet at the front by the light?

It is possible to order the confort ones whith camber plate at the front?

Now do a tutorial on how to bleed out

Best Solid looking jack out there..😊

how much different are the Street bs Comfort version ?

WORD OF ADVICE: DONT BUY THE DAYTONA BRAND. Got all of two uses out of mine and now it doesn't work.

You say "torque to spec" several times throughout. What is the spec?

На какой система работает этот двигатель bosch или Siemens?!

Does the CD version of the VDO work in conjunction with the 6 CD changer in the trunk? The car is a ‘98 Z3 M. Thanks

Awesome Now I can do that to my 1 and 1/2 ton I call it a Dana because enough of the letters on one side that says Daytona came off and it says Dayna.

Awesome video! If u don't mind me asking: what transmission fluid should I use for my transmission? It's a 1998 z3 328i and it has the same MTF-LT1 sticker as your transmission in the video. What oil do u feel is best? Thanks

Bro people can roll fenders perfect with a base ball bat , your Amazon one will do fine , n not just saying that because I have an Amazon one.

I’m bending a fender, not a steel rod. I could care less about the thickness. As long as it does the same task

Dumb question, but would this be the exact same process, kit, etc. for a ZF310?

Does the thickness of the metal really matter? I haven't tried this yet so im not sure the amount of force applied. The jack screw and welds are the most important

No antenna?

How thick of concrete did you go with?

did you get these through the website?

Just bought one , very nice and straight to the point , thank you!

thanks!

Have you ever, or heard if it’s possible to rebuild the syncros?