![Ryobi 48v Electric Mowers](/img/default-banner.jpg)
- Видео 30
- Просмотров 45 878
Ryobi 48v Electric Mowers
Добавлен 23 июл 2023
Ryobi 48v Electric Riding Mowers
and Zero-Turn Mowers. Modifications and repairs.
and Zero-Turn Mowers. Modifications and repairs.
Ryobi 480e mower Soft start with gauge and switch. https://www.facebook.com/groups/ryobi48vmowers/
Ryobi 480e mower Soft start with gauge and switch. groups/ryobi48vmowers/
Просмотров: 727
Видео
Ryobi 480e riding mower drive controller replacement with Flipsky 75100 pro v2
Просмотров 3,8 тыс.4 месяца назад
Complete instructions to replace orginal controller with a VESC. this includes removal, wireing, sealing installation and programming.
Flipsky 75100 Pro V2 VESC Tool setup for my RM480e mower
Просмотров 5455 месяцев назад
This setup includes all VESC tool settings to make the drive motor to run better than the original controller in the RM480E.
Flipsky 72100 Pro V2 installation in a Ryobi RM480e electric mower
Просмотров 7215 месяцев назад
Installation of a Flipsky 75100 Pro V2 VESC in my Ryobi 480e riding mower.
Ryobi riding mower battery gauge set-up for lifepo4 batteries. Flytree FSRD 100V gauge.
Просмотров 3,5 тыс.6 месяцев назад
Ryobi 48v Riding Mowers gauge set-up for lifepo4 batteries. Most gauges don't have the set-up button. I purchased this one from Aliexpress. Search Flytree FSRD 100v the cost was $14 US dollars on 1/3/24.
Noisy deck motors on Ryobi 480e riding mower.
Просмотров 1 тыс.8 месяцев назад
How to replace noisy deck motor bearings on Ryobi 480e riding mowers. Check your bearings when sharpening the blades. Watch the first 30 seconds for more information.
Ryobi 480e Rolling the lawn
Просмотров 5118 месяцев назад
Spring time lawn rolling with my Ryobi 480e.
Ryobi 480e snow plow compilation
Просмотров 1,3 тыс.8 месяцев назад
Several videos from zero degrees to 10 inch snow falls.
Ryobi 480e plowing below 0⁰
Просмотров 2,1 тыс.8 месяцев назад
Plowing driveway in below Zero degrees.
Winch on Ryobi 480e
Просмотров 4658 месяцев назад
I added a winch to the front of a Ryobi 480e. And added a mount to my Brinly plug aerator.
Ryobi 480e creek crossing
Просмотров 1298 месяцев назад
Crossing a rocky creek on a 480e Credit to Phillip Grace.
ECO-WORTHY battery swap into Ryobi 480e
Просмотров 1,9 тыс.9 месяцев назад
Pictorial for Ryobi 480e mower battery swap to Eco-Worthy 50ah battery by Dave Opsteen @Ryobi48vElectricMowers
Automatic Precharge Circuit
Просмотров 2 тыс.10 месяцев назад
My precharge circuit installation video for Ryobi 48v mowers @Ryobi48vElectricMowers
Ryobi 480e riding mower Battery monitor installation
Просмотров 1,6 тыс.11 месяцев назад
Ryobi 480e riding mower Battery monitor installation
ECO-WORTHY 48v 50ah battery Installation in Ryobi 480e mower
Просмотров 4,8 тыс.Год назад
ECO-WORTHY 48v 50ah battery Installation in Ryobi 480e mower
Ryobi 480e electric mower Lithium battery swap
Просмотров 10 тыс.Год назад
Ryobi 480e electric mower Lithium battery swap
Ryobi 480e and Zero Turn Key Switch Failures.
Просмотров 769Год назад
Ryobi 480e and Zero Turn Key Switch Failures.
You didn’t how hooking up the new charging system…
Great video with directions. Appreciate the help!!!
Where to get parts
If the white large plug is not used how do you get to reverse or turn on the blades
I think the white connector you are talking about is the hall sensor connector. This controller doesn't need hall sensors to function.
I was referring to the connector at the 1:27 timestamp
The controller handles foward and reverse see the wireing section. The deck is an independent system and not effected by this modification.
I have the 30" version. It had a side fill plug, (and no slide out battery tray) much like most automotive differentials, which ususaly is also how you check for "full" as you fill till it begins to overflow out this side plug. My operators manual had nothing in it about this maintenance procedure and no quantity , so I tried doing it the automotive way (which still after a quart did not overflow). So I quit after a quart, but I am pretty sure this was wrong, because after a half acre of mowing, it stopped driving (at lease at full speed). It is in Hawaii and I had left it with my caretaker there. He did all kinds of resistence testing and thought it was a control module, but I am suggesting drainning the gear box and we try and get the proper amout that it takes. What came out was maybe 6 oz..Way less that a quart. Thanks
What are the part numbers for the bearings?
They are shown in the video.
After you click setup motors FOC and click no to load defaults. You skip the stops for usage and motor, they are required to get other battery,
Can't do the knees on the concrete floor, thing.
Awesome! I was trying to figure out how to do this. What size square tubing did you use? U bolt size?
Great video thank you.
I'm installing now. Is it just 4 wires from vesc to motor (not including power) ? I'm not seeing where you hooked up other vesc wires. Excited to get it finished thanks for all the info !
Yes just the 4. The white plug from Mower side is not used.
Just ordered. Hope it goes smoothly. Thank you so much for the informative video. Saved me a lot of time and research. I hope its working well for you.
Can you tell me where you bought your lawn mower
Home Depot in 2018. Look for used ones on marketplace.
Hi👋 maybe you could help me please. I have a flipsky 75200 controller on my bike. everything works fine for me except for one thing. when I move the bike backwards I can't give gas to go forward, the gas handle doesn't respond. it happens when im on a step hell and the bike is moving a litle bit backward becase i stop for a second. only if I come to a complete stop I can give gas . (Bicycles only have forward mode)
I had to change the Drive Motor Controller and that did it.
Thanks for this it really helped...I replaced drive controller with my wife.
How did it work out for ya? I mean my wife is a terrible motor controller. She hasn't got any connections!
I did this mod and after mowing the volts resting are 51.3 but the bar and % show 60%. Charging port blinks rapidly, I think that means its about 80%. Something is not reading correctly? May simply be the quality of the gauge?
What spray can did you use?
Any good penitrating oil. I use PB Blaster or WD40
What are the symptoms that the soft start fixes?
With some mower and lifepo4 battery combinations the battery bms will turn off. When the capacitors in the controllers charge up some bms thinks it's a short and turn off protecting the battery. Another thing with all the controller failures people are using them to possibly reduce failures of the controllers during key on events. The unit uses a resistor to slow down inrush current from over 500 amps for a few miliseconds to less than 2 amps for 5 seconds. Visit my Facebook group Ryobi 48v Electric Mowers
Can this be used with the factory batteries as well? My factory guage is useless.
Yes it can visit my Facebook group Ryobi 48v Electric Mowers facebook.com/share/crHuPRYRvdkE2dCn/?mibextid=A7sQZp
what is the purpose of the soft start?
where can this soft start unit be ordered?
You can text me from my Facebook group facebook.com/share/crHuPRYRvdkE2dCn/?mibextid=A7sQZp
Very good presentation! OK. Where and how can I get one or the plans to make one? Thank you.
I purchased and programmed this "new" gauge, and everything seems to be working... but...my LIFePo4 Eco-Worthy 51.2V 50Ah battery seems to lose some voltage while not being used. After charging with P3648 Smart Charger, new gauge reads 100% and 54.5-55V; but after a few days the % falls to 97 and voltage drops to 53.5-54. Someone else did the conversion on this Ryobi 480e about 6months ago. Is this normal for the LiFePo4 batteries or might I have a bad gauge? I did disconnect the Camway replacement gauge and shunt. Love your instructional video, took a few tries to get the sequence correct with the button pushing.
LFP batteries do lose charge just sitting idle. Just leave the charger plugged in, won't hurt anything.
Do you if this also works for a ZT540e?
Yes it applies to all the riding mowers but the RM 300e
I'm in the middle of doing my conversion. I noticed the guage always stays on. Is this normal? The back light turns off but it continues to display even after turning the key off
Yes it's normal and nothing to worry about. The draw is much less than the self discharge rat of the batteries.
How it is powered?
A small 12v 20ah sealed lead acid battery.
Please do a video on how you setup the new charger
What reason did you do this? Did the OEM controller break? Are you trying to get more speed or power?
The drive controller failed. It's fully programmable. The reverse is very smooth and adjustable up to full speed. The power can be increased but not the speed.
Can you put links to the components you used? I want to give this a go with a 100ah battery
What A GREAT IDEA! JUST GETTING READY TO SWITCH MY BATTERIES TO LITHIUM! THANKS! JUST ORDERED THIS!
You didn’t show the connections you made, your hand obscured the wiring hookup of the switch!
One sidevof the switch goes to the black ground wire the other side of the switch goes to the 4th unused ternimal.
So this will probably sound odd... But since i have 8 18volt 9amp batteries already if I wired them in parallel and used a 18-48 volt boost converter that should theoretically run the mower right? I realize it probably wouldn't have a long run time but i already have the batteries and only cut about 1/3 of an acre 0:05
If you had 9 batteries. You connect 3 parallel sets of 3 series batteries. That would make 52v and 27 ah battery . Using 6 batteries you would have 52v and 18ah.
@@Ryobi48vElectricMowers ..I'm very hesitant to run the Ryobi 18 volts in series..in past ebike and push mower projects I've had issues with the lead battery totally dieing very quickly ( to the point I have to tear the pack apart and jump the cells.. while the second battery is still at full charge..I think it's something to do with the way the bms boards operate... in parallel I could use different amp batteries together in a bank 4,6,9 ect..I have over 32 various ones that get recharged either off the work truck or my solar panels
Will the Battery Indicator still function after this install?
The factory gauge won't indicate proper barrery life. Theres several options. Theres an alternative gauge that displays just like the original but is programmable for lifepo4 batteries. Or a Camway gauge. Both have videos on this channel. Or visit facebook.com/share/ieoP7QBtC9rBMuxr/?mibextid=A7sQZp
Great video!!! Any idea where I could buy a replacement axle breather plug? I have lost it. It cannot be ordered from Ryobi parts without purchasing the complete axle about $450.00
I don't know the hole size but if it's ⅛" Npt (pipe thread) try Dorman 924-262 rear axle vent.
Thank you for the info. I am not sure of the thread size. I'll need to pull the batteries again and check.
I have a flipsky pro v2 on a bafang. But it gives a hard punch to the motor at the bottom of the gas handle. It feels just like a punch u also hear it. Can i get this away by curving the voltage / amps?
Make sure the hall sensors are working correctly when setting up the motor foc. You may be able to calm it down with the adc throttle settings and curve.
Thanks for the video! Note: you can open up the original controller, scrape off the rubber coating on the screws holding the wires and remove the wiring harness intact. There's 4 screws holding a plastic end retaining plate that can be removed releasing the entire harness from the metal box. The gives you more wire to work with and more options to connect to the vesc.
I didn't see the need. Just cut them off at the controller there's plenty of wire.
Thanks so much for detailing your fixes and upgrades. Despite being (slowly) superseded, these mowers are still a relatively basic, but awesome workhorse to have on an acre or 2 with the bonus of being able to be worked on and repaired. They're far less trouble than most petrol (gas) mowers and can continue to be refuelled by the sun......maybe even into the next decade or more.
My ryobi starts for a second with no power, the motor won’t work to drive. If I turn on the blades it’s the same. I have batteries charged. Seems like a controller. What’s the first thing to check
Is this for lithium batteries. Only? I have a controller failure on mine. Should I do this?
It can be used with the factory batteries also.
My ryobi 30 rider, just started doing this, it stops like it’s bogging, just acts like it’s out of power. You turn it on and it works a second, turns off, the battery’s are good, a,ways charged. Seems like a controller limiting it. The battery indicated never worked right, unit is 2 years old.
Thanks so much. Do instructions come with the gauge? Do you have written instructions?
Instructions do come with the gauge. But to get it the most accurate you need to use the manual low and high voltages.
Did you do this to improve speed and power?
Power can be increased but speed stays the same.
So no battery shunt required like with other guages? I like it, and it looks like the factory gauge and no cutting the hole bigger either.
Correct. It's a cheaper option for lifepo4 batteries.
Thanks for the vid Ryan. What is the mod# for the charger? If the 48v 100ah lifepo4 battery was used instead of the 50ah, would the charger still charge the 100ah? And when looking to purchase the charger, are the amps critical and if so what amperage should the charger provide? Thanks!
This is the charger used. Then swP the plastic connector housing for a perfect fit.Golf cart Battery Charger, 48V 13A and 36V 18A Trickle Battery Charger,48 Volt Golf Charger,for EZGO RXV&TXT Smart Charger,Lithium,LiFePO4,Lead-Acid AGM/Gel/SLA..Battery Charger,3-Pin (Delta-Q) a.co/d/428hpgr
Visit Facebook group Ryobi 48v Riding Mowers. facebook.com/groups/ryobi48vmowers/?ref=share
@@Ryobi48vElectricMowers12:04
Sick skid
....No wiring shown..
Question about the software. Are you just downloading the google or Apple app to program it? Just ordered the controller and wanted to make sure that is where I get the software.
The free laptop version is here. vesc-project.com/node/17 The phone app is in your app store I cost about $4.00 search for vesc tool
I used the laptop for initial programming then phone app for tweaks while on the mower. I will be updating the video when doing the motor setup at 30 seconds of the programming portion you click on general motor then large outrunner. The rest of the video is good
Excellent video, thanks Greg!
Noisy mower motors I have. Thanks for the great video Greg!