Видео

I was wondering how did u paint the cabinets in the previous video after they have been assembled, any thoughts on that?

I made some chevron cutting boards today and realized that the second glue-ups are all end grain to end grain. Just wondering how your boards are holding up after 2 years? Any glue joints failed? Thanks Tom!

Hi Tom, A good way to make the cabinet doors with just basic tools to hand. Plenty of good tips and advice always good to know. Your workbench draw fronts and doors look amazing. I'm thinking of re vamping my workbench in a year or two and I like what you have done I will probably go the same way as you in my workshop. As always a great video, catch you soon, take care

Hi Tom great video! What drawer rails did you use in the video? Sincerely, Lasse

Hi, tom, greetings from Texas. You make building those cabinets so easy.

I know what im thinking that vacum is much louder than the mitre saw wow

Great video, many thanks.

Ive just bought this saw and am returning it. The cuts are wavy, i think due to the 1.6mm thin blade. My 18 year old bnq pro brand mitre saw is much more accurate. But much louder!

HiTom, I am looking to build a few cabinets myself. I am looking to buy a cheap table saw. Can I just switch the sawing blade to make the grooves for the back panel? Should it be 6 mm or which thickness? THanks for your help!

just what I needed. thanks

Care to indicate the type of coarse screws you used?

Handrail for staircases is usually around 65mm across and that is the way its placed on the saw to cut the angle cuts. 50mm just isn't deep enough for cutting handrails which rules this saw out for me.

Melhor vídeo explicando. Nem a própria Makita fez um video ensinando.

Mas qual nivelação deixar a maquina no ponto 0 ? Antes de colocar as laminas.?

I bought a Mikita and it’s seems to jolt everywhere, even when I don’t put a lot of pressure on it. Is it faulty ? Or is this normal!

How did you get to finish it in white or grey?

Thanks for you....❤❤❤❤❤✌✌👍👍👍👏👏👏👌👌👌👌👌👌

Nice one, I was reading the instruction manual and started crying, you saved the day

Nooice!

Nooice!

Should have done the cut the hair on the back of the arm test

Nooice!

I wish more people would realize mdf and HDF are amazing products and I hope people don’t frown upon them any more

Lovely. Thanks!

Good tip, Tom

Nice job, Tom

Have fun with your new angle grinder, Tom

This tutorial is just what I needed. Thank you 🙂

Great tip there, Tom

Great video! But why is this video shot in mirror?

I got pack 20 blades for my Makita for £14 The vibration is super low the power button locks unlike DeWalt The quick release on DeWalt can get in way the Makita quick release won't . The brushless Makita will last years the dewalts smaller motor won't and will run hot . Makita have nailed it with their Multitool here Tbh the 51 is brushed version of this and bit cheaper but everyone is cheaper than Screwfix £190 they seen you coming I paid £160 and got a case .

Hi Tom, good tip for prepping and painting MDF. MDF can be tricky to paint and get the finish and the other thing with MDF is choosing a clear varnish to keep the MDF look. As always a great video, Take care

I find the microfiber rollers or close pile give a better finish than the foam rollers.

Hi. Great video. I learned more in 4 minutes than I did reading the entire manual. Thanks for that !

❤😊

Very nice. Whats your method for painting them? Can you link to any video tutorials please?

Hi Where did you get the storage bag for the this sharpening tool from?

I take it that this is only of use after you have flattened the backs on conventional stones. Looks useful for primary grinding, but puzzled by the use of such coarse stones for the micro bevel (I assume that is what the 27.5 deg is for). I follow the Rob Cosman method- the micro bevel is put on with a 16000 grit (ceramic) stone, and takes a few seconds. When that is too large, a tertiary bevel can be used. Only after many sharpenings is the full bevel re-ground. Grinding to 1200 grit is very coarse, and, if not using finer stones, will require a lot of lapping. Personally I use 1000, 6000, 16000 grits (first two only for re-grinding the bevel and initial flattening of the back); no lapping (stropping) is required.

I have the same model you are exactly right in what you say about the supermax 16-32 drum sander. It massively improves productivity. It doesn't take 100% of concentration when operating as long as the ( Goldie locks) spot on the fead belt has been tensioned in . Sometimes, if it tracks towards a side I put more tension on the side it's going towards + slightly loose the opposite 😊 rinse repeat a little bit. When it dialled in its a game changer 🙌 👏 👌 😍 😊

Hi Tom, Great demonstration on your new sharpening jig, looks decent and easy to use and if it brings old chisels back to life it must be worth it. Great video, Take care

Makita should have made a system thats holdup the safetyguard. I always use a woodclamp

Nice one Tom, thanks for the walk/talk through of your new Makita… 👍🏻 I am not a Makita fanboy, having invested heavily in another well known 18v platform, but their Track Saw offering doesn’t cut it… 🤷🏼‍♂️ Long story short, I didn’t really want another battery platform to worry about, but have been thoroughly impressed with everything I’ve read, seen and heard about the Makita, your presentation included, so I’ve only gone and ordered the corded version… 👀 I have also ordered the track and paraphernalia separately to suit my needs, including a 1m + 1.5m track with bag, joiners plus fast action clamps… 👏🏻 Can’t wait to receive it all and get started, thanks again and now sub’d… 😉

Hi, great video on making cabinets. I'm wondering what thickness did you use for the back panel? Was it 9mm? I'm building a larder cabinet to fit beside a fridge in a kitchen., roughly 2000 x 500mm. Would you go MDF or melamine. I'm painting the outside panel and doors. Thanks

I have the Dewalt sander. My battery mounts sideways…. DCW201…

I bought it and the build quality was substandard. Footings were weak and wobbly. I had to return it and would recommend to avoid. Side note: I’m a professional engineer and big fan of Makita. They just missed the mark on this and assume a third party manufactured it outside of Japan

Both Top Quality Orbital sanders.Why not get a cable and a battery version. Good investment.

Think you have more hand grip choice Mikita.

Suppose the cable version would be more comfortable but then not as portable

Hi Tom , great work looking at building some cabinets myself for self imposed shed time, thankyou for sharing your knowledge. From video looks can tell, did you use 18mm MDF? Is there any difference if using 15mm from your experience? Thanks Vic

MUCH APPRECIATED!!! Going for the Makita 42L HEPA instead