Видео

Yep as a teenager I would be up to 2am rebuilding engine for Saturday bike racing, two stroke porting fun 😊

ive got a 110cc pit bike, that i need confirm timing on.. How do you remove that cam cover? Mine has no bolts...

Sound mate it's just iv got the 9 year old grandson a m2r kmxf 125 and 3 gear is jumping and grinding iv oderd a new gearbox just wanted to see you strip that one mate 👍

Do you happen to have a part number for your flywheel puller?

There’s an engine rebuild video on the channel dude

When you starting the rebuild mate I'm doing the same but I need to follow you doing it

Are those 2 washers wrong at 0:14, the first one off is from the opposite side by the clip I'm sure

Love

Have the same on where did you get the chain slider

Love from Bangladesh 🇧🇩

zero

Where is the finished ATV. We’re thinking of converting ours to this black & purple camo.

Can the flywheel puller be purchased through Amazon? I have a 125cc with a suspected broken Woodruff key.

What is that last piece on the clutch with the three ball bearings? Opened mine and it was off in the oil.

My second was slipping, took it down & gears look just fine. Anyone have any suggestions. I need help.

Very helpful

No puso a punto el balanceador de vibraciones

I had one very similar i loved it never let me down a bit lost the coppers a 1000 times easly 😂😂😂 good times wish i still had it they cost a fortune now these classics

When you fit the clutch basket that is the time that you need to time up the balance shaft, the crank needs to be at TDC. There is a mark on the crankcase that need to line up with the 'pip' on the primary gear. At the same time there is a mark on the gear that drives the balance shaft, it must line up with a mark on the engine case. If you don't do this the engine will be very badly out of balance!

I've got a 125cc atv here semi auto with forward and reverse gear. Problem is it'll only go into reverse and neutral. The clutch plates are all worn away, do you think that would be the reason it wont go into forward drive? And if I bought a full new clutch basket with clutch plates init that would sort it or do you think the gears cogs could be knackered also. Thanks

What size motor is that

I got a question if u could help me so the bottom of the 110 cc has two bottom screws one for the oil and the second one has i believe its a spring and a part what exactly is it and how does it go back in the rigjt way

Hey man I got a question if u could help me out what's the thing next to the bolt for the oil. I believe it's for the Cam but only two bottom bolts and ones for the oil and the other one has the part I need information on and help please and thak u

Hi, How did you get the last smaller bearing out? The smaller bearing that you said you had to "pull on" to get it out.

That brassy clutch washer you hold in your hand at 4:46, you must bend one of those 7 legs into the grove on the backnut ( once backnut is tightened). Otherwise it's gonna fall apart. It might take some time, but it will. Otherwise, a perfect video. Subscribed

Can you do test ride

Is this a dry or wet sump?

I have a 2017 ssr 125 . Tore it all the way down , checked gears . None are broken . Motor sounded good but won’t never go into any gear . I’m going to go ahead and replace all gaskets when putting it back together. I’m going to replace the small spring on the gear selector assembly. Do you have any other advice on what it could be ?

how tight should the spring be?

Not a lot of information going on here

Can u tech how to adjust balancer

Thanks

Thanks for da video

its great to see how people use their own time to provide free education, Thank you

Looking to replace some gears in the gear box. Does the head have to be removed to be able to open case and replace gears?

Good grief you don’t hammer them in 😮😮😮

ruclips.net/video/e7BRyXXg_KU/видео.htmlsi=XRTIVIoXo0nktWM9

Where did you get the tank !

Where do you buy parts from?

Not that I'm an expert but surely you'd crack the head bolts with engine still on bike? Great work. Oh and what was wrong with the bike necessitating the rebuild?

Hi mate do u have part 4

Hi at 2min in the video u disconnect those wires from stator by tapping the star screw open please show how to connect those 3 wires 😢

Your method is rong . you don't know how to put bearing . these bearing will make sound like shooo. Shoo.

bad restoration😂

If you can assemble like that first 2mins you done with with the bike 🚲 you are a free man 🤣😂

Do you recall what flywheel puller you used? I am working on the same engine but cant determine what one i need.

Hello friend I want some parts h100s can you give me

What way did you but the rings on?

I got one too H100 is the king of 2stroke fr

Do a drive test bro