Видео

How far can you stress the modded switch running linux playing a game like for example, "ultra kill" Out of curiosity

5:30 what game is this?

nice video bro keep going

Ayy stop making videos like this as this is probably the easiest way to kill the ps3 a shaving blade and a pair or pliers come on just terrible how many ps3s have you killed using this method

Great job as always, thanks dude!

Why would you delid the cpu tho? Thw Cell CPU is a tank!

There was no hen in 2010.

Delid it bro

It's nice to see this be experiermented with. But i think i'd stick with my PC for higher fps gaming. And keep my BC PS3 with stock clocks.

Razer with fingers works better. Less likely to mess up.

Sir i just wanna ask if you have back up nand?

if you have a CECHA console you should be completely removing the 90nm rsx and swapping it for a 40nm.

Thanks for this video, it helped me .😊

It’s kinda too much for a ps3 to fix see im just a kid I would need a lot for that😢😢😢

does that work with anyps2

Hi, I have a question. Can you RGH 3.0 your Xbox with the JR programmer? I found this guy and he’s gonna go RGH my console cause I know nothing about soldering so I’m just curious.

OI eires ele perdeu o usuário tá aqui embaixo no stick

it's a tiny one

I got the yellow light of death after trying this! Never again! Lol

I’ve tested loads of thermal paste patterns on my ps3 and the best one is just a pea size dot you don’t need to put that ouch on my temps never go above 60c while gaming on cpu and rsx

Me 😁

Can this only be recharged?

-10k

Couldn't you just also remove the original Ps2 Output and make space for the HDMI output?

Now a question since I thought about doing the same you did: Where did you connect the usb power cable to?

Hi, will you be willing to sell one to me?

The best tool I could come up with to do deliding, was a metallic nail file. They usually have a smooth area of 1cm in the tip, where I bend it to about 100 degree angle. Then grind and wet sand the tip until its something like 0,3mm thick, pretty much as thin as you can possibly get it. Before starting the delidding, heat up the IHS with a heat gun and remeber to pull the tool little bit upwards when your slicing the silicone, so it rather touch against the IHS than the chip below the silicone. If the tool is thin enough, you can easily slice a one side in one motion, then turn it carefully in the corners and proceed to next one without taking the tool out. If the tool is not cutting the silicone easily, then continue to sand it thinner until it does. Also remember to be extra careful and slow when approaching the end to avoid scratching anything when the lid comes loose. This is where many people have fucked up in their attempt, since a tiniest scratch on the chip can destroy it.

works in fat?¡

bro put Way too much thermal past. remember, its meant to fill in the cracks, not add a layer between the CPU and heatsink.

Nice job !

Here in 2024

Hey there! Do you still have extra boards and components left over? I would happily purchase two sets! I have the CPU and PPUs

how to identify VBUS , Ground , D+, D- on both dualshock4 charging port PCB and type c PCB without multimeter ? and did you add any resistor to the type c pcb ?

Do other output work if hdmi is down?😊

Lol, I though you were gonna throw the cpu off the balcony in the thumbnail. 😅

aurorabank.store

My psp has a problem with the headphone input. The sound is all muffled & i tried blowing compressed air to no avail. It's not my headphones either, they work great on everything else. What are my options?

Awesome work my friend! I have a question, what is that hot plate for? I assume you heated up the board but for what reason? Thank you

mmmm mal hecho,

Колхозинг

aliexpress sell cheap converters to hdmi

Beautiful video!

7:42 DO NOT BLOW ON YOUR NES CARTS, THIS WILL EROID THE PINS!!!!!

Good job

2:32 Just by soldering 2 cables? or also solder the middle point?

Be aware the ps2 slim scratches discs

Very good video, unfortunately though I think you broke the CR2032 battery connector. I think those 2 little metal tabs on the top snapped off when you put in the new battery, I noticed the orbs in the main menu staying still, which means the battery is dead, or not put in correctly.

You are an artist sir

This killed one of my ps3s. I kept the rest of it for parts. From what i read, its been proven these don't cause YLOD. The capacitor chips tokens right below the cell and RSX are what go bad.

NOSSA VOCE É MUITO INTELIGENTE