Видео

I’m so cooked

OMG that is a brutal process if we cannot find the tool.

Is it possible to add ambient lights to endeavour 2 GT when I upgrade it to FOC 3.0? Will lights from endeavor 3 GT fit to 2 gt with new foc??

Fantastic!!

About the headlights. My dear Friends, a m found that position of headlight is too height, and the people that coming against you are blind. y must create adjustment for lights, depends on weights.

Huge design fail....Sad

Hi, do you have a service centre in Australia? I need to get the charging plug replaced. Thanks!

Oh boy was one of my bearings ever stuck in there... ended up putting a washer in there to protect the shield, put a socket on top, then smacked it with a dumbell.... FINALLY came out.

Io non ho l’attacco xt30 e xt60 in entrambi i lati ma solo da una parte xt30! in più ho in dotazione un cavo corto 4 pin per lato, il cavo lungo xt30 che finisce a 2 pin dalla parte opposta di cui parlavo all’inizio, in più un modulo elettrico senza scatola protettiva che non so come collegarlo e metterlo! Il bottone fisico sulla boccola per accensione e spegnimento fari non c’è!Illuminatemi grazie su come devo collegarli e farli funzionare senza nemmeno il bottone fisico? Grazie io sono possessore in un Endeavor 2S

Is this GD suitable for endeavor pro 1?

*Yewwhh!* 🤙🏽⚡️🤟🏽⚡️👌🏽 Wish more brands had belt drive guards/enclosed

hello, can you please make a tutorial for how to replace the light color for the endeavor 3 gt suspensions?

Love the Chanel Russ, very useful information. I'm on the heavier side (230Lbs) so did a swap for the black bushings. After the swap my board (Endeavor2 GT) won't turn back on. Battery fully charged on the board and remote but can't get it to turn on again. Any suggestions?

RUSS IS THE BEST !!!!!!

every time in winter i do maintenance. ш dont want your problems. 😅😅😅 But if y broke screw extracto....

Does the drive gear come installed on the motor shaft?

Will this provide smoother operation and not have the twitchy throttle response and jerking motion of the board?

Is it worth upgrading from GT 2? What will improve if I upgrade it to FOC 3.0?

This is amazing. PLEASE tell me you are going to support FOC 3.0 upgrade in the Endeavor 3s as well? I thought it was going to have the 3.0 in it from the factory and was super bummed when I realized that isn't the case. I would happily pay for this upgrade, and have already bought the color remote. Any good news on this front you can share? The unprogrammable speed modes of the 3s are untenable - speed mode 3 is slow and can't climb hills, speed mode 4 is an unsmooth twitchy rocket ship. I wish I could talk to whoever programmed these unchangeable speed modes in the FOC 2.0... Did they even test them in real world conditions?

Anyone tried these - how much difference do they make?

I wish so much, that adjusting belt tension can have so nice video like this one. Maintaining the belts is basic and important skill and the video about this is because of wrong camera angle in the second part of the process useless. We even not seeing what is the guy doing there, with a zero relevant explanation. Dear Propel, nothing in bad, I love you, but please can someone even answer my question in the comments there..?? I'm not much technical type of person, I don't want to f*ck up something accidentally, I need to understand the things..

Great video! I did this last weekend on my Endeavor3. I lucked out and did not have to heat any fasteners for removal but I did have to Dremel a bit of clearance for the shock end on the control arm fastener brackets, not difficult.

I wish you guys would make reducing gears for endeavor 2 , lower top speed , higher torque and acceleration. Can you make this?

A lot of heat is needed to heat it. Got it.

Axel broke on ruckus skateboard how can l get replacement

hi, I would like to learn how to adjust the belt tension, but from the video I have really no idea what to do with a screwdriver. You are using it as a pry bar for prying rotating part of the motor upward?? I'm not seeing any other solution because of a cable to the motor (endeavor 3s) ..but on the other hand prying some rotating part seems for me not like something correct.. hmmm Sry, for a trivial and maybe a lightely stupid question, but I'm really not that technical type of person, my occupation is far elsewhare and I have almost zero experiences in maintaining a mechanical things..

Hi Russ, I was wondering where you can find the total board odometer reading? Would I need to connect to VESC tool on the computer? Thanks

epic board,best at market

How many turns I can loose turning tensioner at maximum? I put black bushings, because it's recommended to my weight (100kg), since then board is not turning well. When I bought board it came with grey bushings, I was able to push the board to the limitter at low speeds, now I barely turn. I already loosen 5 full turns which wheels like a lot, but board is still very stiff. Should I keep loosening it or switch back to grey bushings? I like to carve.

I Was Wrong, It Is That Bad. Its All pretty much necessary. Flashlight tied to my head here I come.

Wow. Guess I'll be HeadLighting! Everything after "Take the Deck Off......." is nightmare inducing. Also, I don't think that's at all necessary. I think You just screw it in the side and then try to pinch it in under the front nose. Like blindfolded Rubiks cube or something

Thank you for taking the time to do a proper tutorial with all of the helpful tips. You guys clearly have a better understanding of your products than most manufacturers.

Where can I buy that ratchet screwdriver??

So can you not hold the break without going backwards? For example if you on a hill at traffic lights and you need to hold the brakes so you stay still?

Do you have a video for a CycleEagle X4S ESC swap. I am currently swapping to old direct connected ESC for the two wireless ones. I don’t know where the bluetooth wire goes.

FWD - REV Switch = Thumb wheel down full brake + Select button (below power)

Hello there! I just got the propel endeavor S3, the thing is that I over spined the Tension adjustment ring and the shock absorber is over the thread now, so I cant find any tool for getting the shock absorber to its initial position. Do I have to get a new shock absorber? 😢

1:40 I'm not able to install the circuit fixing plate correctly. I don't know what to call it, but it's that half circle pad that's in the center/in between the fixing nuts that's blocking it. Any suggestions how to remove it or fix it?

Very helpful. Just got an Endeavor 2GT. The wheel speed with 8" tires from the factory is set at 73.......is this correct, or should it be 80?

Link to video for the Color Screen Remote?

Will 2 of those batteries fit in there

How fast is it and range?

You going about 18 to 22 mph?

Hello, on the right rear wheel, I have a problem removing the block + the wheel. Let me explain: when the wheel is screwed, it is notched in the gear. when I unscrew the main screw and push on the axle while performing the movement, this causes the wheel to come out of its notch and spin in a vacuum. This way or the other nothing happens. Any clarification on the procedure to follow please?

So I don't know what I did but for some reason my belt is rubbing up against the frame

Thanks for this Russ, good informative video, great idea with the wires 👍

you are master of belts option...is so amazing of you used screwdivef

has anyone done this successfully without the setup that this guy has (e.g. Board bench with straps and tape) ? I asked if they could install the lights for me and they wouldn't and told me to watch this video and now i'm watching it it seems like a giant pain

Do you have any suggestion about how can i replace 8 inchs tires to 10 inchs tires? Or do you have any link about that? thank you!!