Видео

Oh and I could not go anywhere in those temps you go boating in. For Me as you know John its 25c plus to do those things.

Yep, gotta keep on the straight and narrow!

All on the website www.marsons.se Tom! Have sent you an email btw :)

marsons.se 😀 You'll need to contact us for a manual order atm. have a great day! /John

Might give it a go one day!

Sorry there! I just mumble away as if I was in Oz! 😅😅

Yep! ⚡⚡

Can't quite remember, it was a while back now, but we sell the motor and controller on www.marsons.se, so you can check and start there with those components. Thanks for the comment. /John

Do it! It is super fun! /John

Hehe, thanks @ludi1403 :) No dramas, just a pain in the bum when you just want to get stuff done! 😅😅

Hi @s20000 ! We are now taking orders on the website, check the info about our production runs. have a great day! Regards John

Howdy MrQuasar! There's a few vids in the series, plus a few of our other videos where we go through stuff like that. Hope those videos help! More info on the motor can be found on the website www.marsons.se Regards John

Howdy, I don't know, blows a lot of other airboats of the same size and category out of the water. But it sure has it's drawbacks, no doubt. Thanks for sticking around and watching, have a great day! /John

Hi Phillip! I reckon you could! Thanks for the comment, have a great day! /John

@@johndehosson when Will your motor be in stock?

Check out the website for pre order for next production run👍👍

Efficiency is ok, we cover it in one of the review videos! Thanks for dropping by, have a great day! /John

Thanks for your comment, and yes, this is particularly true! There is a lot of junk out there, particularly on Amazon etc. In any case it is paramount to work with quality materials and the best people to make good products. We have found our team in different geographic locations, and the Chinese have proved an amazingly reliable an dhigh quality supplier in these regard. We produce a number of parts there because they are so good at what they do. Thanks again, and have a great day! /John

It's in Åre, Sweden, a fantastic playground somewhere north:ish in Sweden! Thanks for dropping by, have a great day! /John

www.marsons.se 🙂

THen you need to get it! Specs here: www.marsons.se 🍻

Hi @KingShinobi82! It is some mucking around! If you don't quite have the knowledge it can go a little wrong...... We have them pressed in the factory nowadays, so we don't do it ourselves now that we've developed them as such. Not sure what motor you are using, but try undoing every single nut/bolt/shaft/wire/sensors, and then giving it a "bashing" as violently and carefully as possible.......😅 Hope this helps, have a great day, and thanks for sub:ing/following if u can and want to! /John

@@johndehosson violently is how I do all my work 😁

@@KingShinobi82 🍻🍻🍻

Cheers @g.v.m 🙂

www.marsons.se. 💪💪

Dictates so much of what we achieve!

Electric motors can generate a lot of heat when under heavy load. Heat decreases efficiency dramatically, and can also lead to burning the motor out. This system requires water cooling for both reasons👍 Have a great day!👍

Thanks For that mate. Now I know why you have to use water to cool it. Thank you.👍👍

Very true, that is why we use galvanic isolators on the boats, keeps that at bay pretty much! THnaks for watching! /John

www.marsons.se ⚡

@jacobclark89 Great thoughts! The rpms don't have too much to do with the heat generated in this case. It is more to do with the small size of the motor and the amount of work it needs to do with it's accumulated inefficiencies, that produce heat. Higher voltage could be more helpful in some systems, which lowers amperage, and heat build up. But in this case, a larger motor, higher voltage, and less amperage would be the fastest way to a more desirable outcome. Thanks for hanging abnout! /John

@luisalbertomarrugorocha5884 Thanks for your question! Check out our videos for the battery specs, and the motor can be found on www.marsons.se ! Have a great day! /John

@onedodger1 Thanks uncle! 🍻

THe cells are very high output so 4C is no problem. Thanks for dropping by! /John

You can find it in our webshop, www.marsons.se🍻 /John

Jack and I had some fun with this one. Cheers for dropping by @explorster 🍻

Cheers!🍻

www.marsons.se 🍻

www.marsons.se 🍻

Any song can be done............hit me 😅

Cool🍻

@aussie2uGA 🍻🍻

@SuperLava55 Yep, would've been great, but Jack had it up north 😅

@SuperLava55 Not like Aussie windows, these windows are triple glazed. Every winter gets down to -20 °C, so the windows are made for that 😀 Up in these two rooms, we'll only have electrical heating for the start, but with time, we'll connect it to our central heating which will be installed next year, and this is heat pump driven. BTW do you remember wood working classes at St. Joeys, that was epic fun😀

@earnestbass4043 THanks fro the comment! The motor can be purchased on our website: www.marsons.se, and modulateing the speed is with a remote control. Have a great day! /John

@luisalbertomarrugorocha5884 Sorry! If I could speak Spanish I would! But I only know Swedish and English! Thanks for dropping by, have a great day!/John

@iamkian Great idea! I'd had a glass of wine and it didn't occur to me, but I'll do that next time!😂

@joshoelze 😔That's super disappointing! Mammotion really need to sort customer service put, this kind of treatment is super unfair to customers. I have a couple of contacts at the company, so I'll see who I can contact there and get them to assist. Contact me privately with your support ticket and I'll see what I can do👍👍 /John

@@johndehosson Thanks John, sorry to dump in your video comments (cool video!). I really want the LUBA to work, but I (and many others) feel robbed by Mammotion, and I am not sure what else to do other than warn others and make commotion about it.

@@joshoelze No dramas! Mammotion need to hear this, and of course it wasn't taken as anything but purely ur message about their customer service. 👍 Happy to help, thanks for the DM, have answered U there 👍/j

Cheers @petleh82 ! THanks for dropping by! Jag byter till svenska..... 😀 Jag har själv tänkt på förlängning av RTK- signalen, då skulle man kunna få bort "black-spots" på tomten. Snygg kanal förresten, kommer du lägga upp nya videos, ser att det var några månader sedan sist! /John

Hi @DEAFB33F👍Very easy to adjust small parts of the perimeter and no-go zones afterwards. Not sure about spares, but cannot see how they could be marching forward without this👍Haven't needed anything ourselves yet, thus the incomplete answer, sorry! But hope this helps, have an epic day 🍻 /John