Видео

I have the Avanti S v2. I will make very sharp balsa trailing edges and see what it does… Stock setup I got 225kmh so I hope to push 275

This channel is dead ?

you used almost 1000mah in a single pass something is wrong

just invest in some spot welder... I wouldn't want to touch a battery that was heated to that degree. Also, did he use file on a iron gun? Facepalm.

6:45 That is absolutely not true. You WILL smell the resin, and you should never be 3d printing in a room that people use unless your printer is in an enclosure that's ventilated to the outside. Opening a window is not going to cut it.

3:56 Wiping those gloves with paper towels isn't enough to get them clean. There will undoubtedly be uncured resin left on them, which will then get on everything they touch. That's one of the reasons people use "disposable" gloves.

Sound is Fake

Hey man, miss your content. Please upload some more videos LOL

Do you have two sets of 8s3p in total 16s3p ? how the batteries handle current consumption - one Samsung 40T battery IR21700 4000mA, max.discharge current 35A. Jindra.

Awesome pilot and great setup. What is your battery configuration ?

Any plans to test the molicel p50B? Looks extremely promising with a 60a discharge on paper.

I'm sorry that I didn't get into the hobby while you were doing videos. If you or any of your viewers can recommend an ESC for 7s and up maybe 120 minimum amps . I'm not rich or I would spend 400 $ on a high voltage SPEKTRUM. That's what I run is SPEKTRUM. But wanted to check out something else. Bec or not I can go either way. I'm on Vancouver Island British Columbia Canada. So shipping cost can be an issue as well. Thanks so much for your videos hopefully you are healthy and same with your brother in law.

Вы пробовали печатать высокотемпературной смолой Siraya Tech Sculpt или Sculpt Ultra? Насколько она хрупкая?

Absolute pleasure to listen to. This will save me a fortune in wasted resin and time. I salute you.

Thanks forthe tips and video recommendations!

Mate are you still ok ? I hope so. Coz no more video is coming from u

Recently did order 4 of these p45b batteries for my fpv, happy to know those are great batteries, curious about if you share of sell file for the 3d printed cover that you use on yours build for build 4s of them

Would have been cool to see exactly this setup with JP40 cells reaching much more power and speed :D maybe even 12S1P with shorter full throttle passes….

הפסקת להעלות סרטונים כי אסור להטיס?

Sorry I am a very late subscriber but I just picked up the hobby one year ago. I have advanced quite fast and love your non stock set up. Let alone how you are making your own batteries. I wish you had new content but your old stuff is all still new to me. I am very interested in lots more you have to share. As well if you still have a drawer full of stuff like edfs and ESC I would be interested in purchasing some. Not rich but happy and love going fast. Hopefully you are well and same to your family. Commenting from Vancouver Island British Columbia Canada.

Hello , who can help me with the STL files for the bracket/ battery holder ? Thanks , Bruno .

We are still not seeing you for a while again. Bro vanished again.

why would u use Li ion battery? what the difference between the lipo and li ion? ive never try that before

Cześć. Coś nowego z żywic wysunęło się na prowadzenie?

Amazing. How much is the cost for the kit

Great video. Any tips on post processing the Build / Tenacious resin mix? 405nm light in hot air or water cure?

Haha, I only noticed you were Polish when I started reading the notes on the bottles :P

My first 6S1P Molicel P45B pack weights without plastic holders (because I did another geometry and some special tape on contacts) just 426g ready to fly!!! I was amazed!!

Hi Wojtek, this is the x time I see this video. Today again because on the weekend after crashing two planes I did something good and soldered my first p45b 6S pack. I had a voltage drop to 3,45V but steady on that voltage. That meant around 10-15% decrease in thrust compared to my best graphene lipo. So to have more power I´ll need to go 7S or 8S or use motors with more KV which isn´t so handy having many different planes. But I was pulling just 47A without almost any heat. I´ll keep on them. Cool that your XT60s work also on that heavy current! I´m now also using them. Cheers!

Where have you gone no more videoing

Ethanol vs isopropanol. Good call.

Lol imagine what he does when he tries the Ampace JP40

Wojtek! Amazing videos! Very pleased to watch every one of them! You made me switch from gas warbirds to EDFs and li ions! Waiting for your next project! Thanks

Wow, that sound….!! But no LiIons?

Thank you SOOOOOO MUUUUCHHH !!! Exactly the information I was looking for. I think I'll go with the build because of the high temperature resistance. I'm designing a custom resevoir for my waterloop in my PC, would hate to see it melt when the system is under load for a very long time.

At one point I recall you initializing an esc with either a dead battery or with a smaller cell count battery then flying it on more voltage or cells. Can you point me to that video? Or do a video about how you tested if your esc would manage that or if it is something that can be done with other esc too

I love this airframe, also my very first V1 70mm Avanti from FMS and the new 90mm to maiden…

And here almost 5minutes flying just on a lipo!? 👍🏼

I enjoy all this videos! Just the landings are sometimes rough but the landing gear seems to work fine! I’ll begin to fly LiIons and maiden my Avanti and L-39… I have also some 90mm with room for LiIon and ordered 26 pieces of P45Bs, now for €5,20 :D

Very nice setup and flight! So 1P get be achieved too :) 👍🏼

Hi Wojtek, have you got a 90mm Avanti :) ?

Geezus Christ I can’t even tell, it sounds like a damn turbine. Nobody would even know that it’s electric. Amazing !!

we miss you

Incredible and amazing.

Possible to share the 3d file for the covers

I cant find much info on using lion batteries anywhere, all I can see is they dont go up to 180a, how do you make that work?

are you still using molicel 45b? if yes but they are rated at 45amps but u push them to 150amps. how is that work? thanks

should probably use fdm instead of resin

I really enjoy your videos and it reignited my interest in the EDFs, they have progressed a fair amount since I last flew. Time to upgrade my batteries and fans!

I have used resin and UV to "glue" together before hadnt considered that the UV might not reach deep enough on the usual grey i print. Will change to transpartent as that was a brilliant suggestion. Also I have had a couple of larger hollow figures that even though Id washed had uncured resin inside. The figures ended up cracking due to the uncured resin. Transparent would fix this issue. 👍