Видео

@@robertf4572 This was Actually Taught to me buy one of the best head mechanics in my state for subaru’s and i have never had any customers come back for head gaskets except if they blew a radiator or hose and drove it till it shut down but then they needed a engine cause everything warped beyond repair.

Even Force and to keep head bolts cool so you can get a even torque and yes on all 🙂

@@jonnysanchez3833 Just call me Old

@@deanjet I only got this 1/2” and only gets used for head bolts 🙂

sure is just had to do a tool check🙂

whoops

Yes, a Brace has a chuck on it, but a speed handle has a square drive on it per the size sockets used. Thank goodness for power drills.

@@blakeXYZ Check subframe front and back for rust. Be prepared to replace turbo and i recommend replacing oil every 3000 miles because of turbo. If it automatic change fluid and filter if it spin on external filter and if it don’t have it just change fluid and not flush and be prepared for wheelbearing but i recommend none turbo for reliability and turbo for fun 🙂

And that’s why i do a good job cause i don’t skip on details but the full video is on My Channel of showing the correct way to do it and not the chilton manual

At worst, it makes no difference. It can only help to clamp the head more evenly. It is literally a difference of a few minutes. Seems like a ridiculous thing to insist people skip out on.

@evanchi9460 Skip out on what ?

@matthewwhite4799 In reference to Kevin suggesting it's just a waste of time. Skipping a few extra 10ft/lb steps.

with something as easy as this i’d rather be safe than sorry, as the other person said the worst it can do is nothing

@@AleksanderSzadurski 5 Dollar homie

Speed handle, still got one. 😅

@RogerDurham-v9s Tool Check 🙂

Now that i do not know because i always reuse head bolts and Thank you 🙂

You can on some years without the egr tube but with this one it would be a pain to tighten the tube but still possible but you could stuff a rag down where the torque converter bolts are so you don’t loose them and Thank You 🙂

That’s good everyone needs to find a way that works better for them 🙂

@@FreshMikeable yes the leak externally because of a design flaw with the head gasket and when they actually overheat and blow the head gasket it pushes exhaust in to the antifreeze and it has to be real bad before it mixes antifreeze and oil but by then you might as well junk it because of too much warping and damage 🙂

@@jeanemil8988 Sure is 2.5

@@brucecolby5016 you like 🙂

🤣🤣🤣

yes 🙂

@@matthewwhite4799 thank you

@ You’re Welcome 🙂

It can get you in trouble especially if you don’t watch the full video 🙂

Now That’s Extreme I haven’t had one come in that actually had loctite on the head bolts 🙂 yet

You ought to see how these dealers treat your stuff

What you talking About Homie

@@johnkelly8525 Do what ?

@@johnkelly8525 just to keep the three layers together so they don’t expand past the dowel pin when i put it together it just makes it easier because i removed the rivets in the head gaskets

@@johnkelly8525 they are in the engine block but be careful not to let them slip 😂

@@onlyrotary17 well you would have to ask him but i would say junk it🙂

@@EchoConstellation Instructions are good but the teacher is always better

@@nickfoy7430 well this is definitely not a high performance engine but i would still do it my way got to have that smoothness 🙂

@@paisleyprince5280 and i have never used new on a subaru now other vehicles are different

never heard of that on head bolts

definitely not right

Everyone doing anything mechanical deserves some instruction in what nut factor is and how it affects indicated torque vs bolt strain.

yes but never heard of dry torque on head bolts

@@matthewwhite4799 all depends on application, some Honda engines call for a dry torque on the head bolts

You welcome but the bad thing is you have to go by what the boss says though and most of the time they ain’t the smartest 🙂and Thank You

This is not a laughing Matter 😂

@matthewwhite4799 😆

Pulling the rivets it’s on the longer video🙂they only gave me 15 seconds for this short

This guy would not know if his arse was on fire

@ Probably not but thanks for the compliment 🙂

@@johnkelly8525 for sure!!

well i guess you can leave them dirty but it probably won’t work

@@robertrodriguez8167 It’s okay trolls ain’t to bad

Definitely not a tech i am the person that knows more 🙂

More about swinging off it

@@GidDree It’s a short from the long video they only allowed me 15 seconds but you can click on my name at the bottom and it will take you to it

@@Formerlywarmer demonstrating purposes 🙂

@@harryford3072 It’s about removing the rivets

@@AllenAdams-u7w I did 🙂if you click on my name below it will take you to the full video 🙂

That’s okay Neither do You 😂

Been doing this a long time...