Видео

omg FINALLY THANK YOU, ONLY video ive been able to find if the wrist pin had those locking tabs or has to be pressed lol jesus thank you.

my pulley puller won't catch and none of my hammers work. do i just need to take it in to a mechanic to get this driver side pin out?

thank you!

What’s up with the mask

You need to speak up, please.

no audio?

If only I had watched vid before replacing mine . Exact same problems . The old bearing thing does not come out at all . Stripped the castle nut ,beat the crap out of it with a small sledge and nothing then beat the crap out of it with a 10 lb sledge , PB Blaster , Torched it ,,ball joint fork,,,,,,,,Cursing,bitching,,,ranting and raving and nothing works........Going for a bearing puller or ball joint press soon ....

As many others will say, the filter should not be in the engine compartment. I put mine down by the transaxle!

Thanks for sharing this video, I got the same brand of pistons ( and sleeves) combo, so you trust the rings position? I inspected one and the rings gaps were not lined up where they should be.

So, is that a Karmann Ghia at 5:42 with front exhaust pipes?

Thanks for the video! My ball-joint press made short work of my stuck pin!

Plz, just stop. SOOOO many things wrong in this video!!

How do u get that yellow wire to go against gravity and be pushed up the wall to the new outlet hole? Do those wires need to be attached to a stud? Can u do this with an existing outlet that is below the TV but off center to where the new outlet would go?

Genius!

Stuck at the same spot with the castle nut. For those without the parts, i used pb blaster. Let it sit for 10mins. Hit it with some more pb and hammered with a claw hammer. Got the job done! Thanks for the video!

Yikes, I am going to watch this video with my plumbing class as what not to to do. So much wrong with this, and you do not use purple primer for ABS. Also, you do not even know what you tied the new sink drain into. In essence you have now wet vented the fixtures below.

Your hands or head are in the way. I cannot see what you are doing. How did you get the whole thing off the wrack?😢

Did you have to tighten the fitting (or whatever) onto the pipe? How does it tightly fit onto the pipe? I have to do this. Getting a new fridge delivered today. The current valve won't completely shut off. I have to turn the water off at the street before I disconnect the old fridge. Once the new fridge is installed, I can turn the water back on. Will have to replace the valve in the wall soon. Thanks for taking the time to make and post this video.

Getting ready to go thru all this for the first time must say I'm nervous 😂 but I guess I should go back and watch part one

🫡🫡🫡

Does this product have a cushion/underlay on the back like waterproof vinyl floor tiles?

Thanks for the video my guy. Didn't really need sound. I comment here because as I'm typing this out, there it has 68K views. Shame on Whirlpool or whoever else all made this faulty crap. 68K views gotta be 50k broken units. This kit should be free.

Great video.

Though adding commentary would help, at least, if you’re not gonna have sound, I appreciate your telling us that there is no sound on this video in your description.

What I don't understand, is if this will need to be done every time the valve goes bad. What happens when the pipe gets too short?

Floor glue is already waterproof. Seems more work with the membrane. , but i understand the benefit of extra protection choice.

I ve a Jeep of 1998, so I need some of part

Give me your contact plz

Why no paper gasket at the base of the cylinders as they come in the gasket kit?

If the engine is otherwise stock but a 1500 case with single relief with added a new doghouse cooler and all factory tin including factory thermostat, are the thin wall 87 cylinders reliable for long time engine life? I keep reading and hearing bad stuff about "thin wall" cylinders. I need my motor to run a very long time. It is stock other than the things above with 26mm oil pump.

Where is a good place to go to get a transmission bell housing to use for the starter?

Terrible design......replacement shouldn't be so difficult. The designer should be fired.

Put this on 5x speed and it’s perfect. Thank you.

was about to call a plumber to do this so we can get our old fridge(that doesnt work) out and our new fridge in. Not anymore. I appreciate the video.

Im facing an issue with fitting my engine into Karmann Ghia now. Its too tight and the rubber insulation around the engine bay is getting in the way. Some ppl say i have to take off the rear tray tinware and install it later. Just too much work

Awesome!!!🎉❤

Nice sharing🎉🎉

No sound.

Sounds good!!

My case has this blocked off. I've been thinking about adding this to add the oil temperature stick and still have the original oil stick.

Nice 👍

Great view of his head and shoulder

Sharp you said? 20 years ago, I lose a part of one of my thinger because of these tubes. Sharp isn't the right word, everytime I need to work with them, I have a deep fear in my guts.

No sound

ruclips.net/video/37re5DStkGQ/видео.htmlsi=3ckZG0zhzOh_AcVY❤

Mmmmm ……. Interesting but I would say it’s more difficult to lay the tile when you use the proper inside corner trims

Thank for the awesome video man. It really helped!

Quick and easy with slotted screwdriver

I got a stroker crank 84MM, I think mine is 450 Ft/lbs. but I'm gonna try your idea.. No van, but i do have good size tractor.. Yours looked like 1/2 inch drive. Mine is also a 38mm nut (1.5")

Thank you for showing this. I was having issues with lining and screwing the heat riser tube to manifold, because i tightened everything first