Видео

Thank you clara . Video is very helpful ☺️

Preciso de ajuda sua não estamos conseguindo cortar chapa grossa acima de 4 mm Se puder me ajudar 12 mm é 19mm Raycos Raytool 3000w

I have 3kw. Raycus and raytools bm111. We have problem with the upper protective lens. When I checked the upper protection lens during the 30-minute cut 10mm, there were about 5 burns. These burns were on the upper side of the lenses. And also it occurs white dots on the lower protective lens. Firstly, I have to fix the upper one. What am I going to do? Thank you so much for all those videos.

Muchas gracias Clara ! Fabuloso tu canal. Qué bueno contar contigo para ayudas en temas de láser ! Éxitos !!

Hi.iam tara from kuwait.i have problem.madam.so please suggestion me.-alram.z axis is not worktable range

i have a problem with the nest, if the sheet is too small and the parts in the nest are many, the function will misbehave, hoe do i know that the elected parts will fit on the available sheet to avoid the error??

When etching or engraving is it possibe to cut in both directions and not just one way?

Hi clara is it better to cut carbon steel with higher or lower gas pressure on 12000kw

De dónde puedo descargar el programa?

Red light error on the remote when operating any buttons?

What error red light indicates on the remote control when pressing any button?

Hello mam firstly thank you for your valuable suggestions it will hepls lot. In our facility, we have a 3000W laser machine with an IPG source and a 16-bar screw compressor. However, while cutting 2mm iron steel, we are observing burr formation. Could you please suggest the best solution to address this issue?" Let me know if I can assist further with technical adjustments!

Hi Clara, We have a 3KW Laser with RayCus Source, we are getting burr in 1.5MM Mild Steel while Cutting on Compressed Air. We Tried with multiple parameters in the final best attempt the burr on the edge was like a fine thread which was getting removed by the finger . Can you please help to fix this so that the complete burr is removed. Speed 18M/Min Focus -1 Pressure can’t be set manually Power 100%

Hi Clara. Are you familiar with TubesT? I can’t find any tutorials like this on TubesT.

Merhabalar şeçili parçalari kesmek için ne yapmam gerekiyor

Good afternoon Clara, I follow your RUclips videos, I have a laser cutting machine that uses the Cypcut program, I am having difficulty making quotes for my clients, I don't know how to program Cyp Cut to show me the cost of cutting and the parts I am producing, do you have any videos that explain how to price the parts I am going to produce?

Hola buenos días tengo una maquina Bodor 1500 pro como puedo centrar la luz roja?

How to remove or resolve custom alarm in max fiber source

Awesome video, very informative and helpful. Thank you

Follow timeout?

Congratulation Clara! 😃

Hi there, please share with me the handout or note pdf?

How to remove or resolve custom alarm in max fiber source... Plz help me as early as possible....

How to remove custom alarm in max source

How to remove custom alarm in max source

Hi Clara, I have a double table plate laser machine but the table configuration details are missing, can you help

Thank you for such informative videos. Can you please share what nozzle diameter did you use here please 1:29, for cutting 3mm stainless steel with compressed air. Thank you 🙂

Good afternoon, when I activate the spotlight configuration, me salta la barba axis 4 limit In the cypcut program Thank you

Thanks! Very helpfull!

Thank you ma'am for taking so much time and sharing you knowledge. I have ordered my 1500 watt fiber source and supplies to convert my current plasma set up for dual purpose cutting. My question is, for my knowledge what would be the safest maximum carbon steel thickness cut you would recommend using an air compressor? Thank you so much!

ya mi suscribi, ya di like☺️

Hello Clara my machine alarms coming capacitance 0 but remove amplifier 4pin connector and put in again fix then alarms gone

You do not give understaning videos its too hard to understand you only speak

Las chispas de perfuracion salen como um fuego

😊

E11 ka alarm kyo aata h

Can you calculate the gasconsumtion in any way ?

hi clara, is my machine having a change focus problem? We have replaced the protective lens, collimator lens and focusing lens. but when I want to use parameters that were previously good, the results are still the same. This only applies when I cut carbon steel, in contrast to cutting stainless steel with oxygen gas, the results are good. what should I do next?

Hello, Clara! Do you know where I could find 2dcutahead 2.0 tutorial?

Hi clarita, I just started to run fiber LBM tube laser machine with 5000 k and I have troubles with the cut condition for 3/8 thick en above 0:06 material carbon steel, can you help me?

Can you give me tutorial about first capacitance calibration trough bsc100 monitor interface(whitout bsc100 phisical controller)

Hello madam,we are also using fiber cutting laser machine,this machine has 4KW capacity,the machine maker team told us it's capable to cut upto 20mm,but this machine does not give fine cutting surface in 12mm,what will I do next?

At the expense of 6 kW and 20 mm of steel. I have the same situation and guess that it is caused by rust on the underside of the sheet