Tips to Startup Laser Machines after Long Holiday | You Should Know
HTML-код
- Опубликовано: 11 сен 2024
- The video tells the tips you should know to startup laser machines after long holiday. You could find the check steps, details and specific solutions.
Our Store: spierlaser.com
View our product catalogue: drive.google.c...
+86-13335151833
clara@spierlaser.com
Join this channel to get access to perks:
/ @clarachai
Hi, Clara here, super happy to see you guys on Sundays. Today we are going to tell some tips to startup our laser machines after a long holiday, like Christmas, Chinese New Year. We will give appropriate suggestions based on the safety and sustainability of machinery use. Click link below, our store could offer you a lot of laser products. If you are first time being here, please don’t forget to subscribe to this channel and give me you like, thank you.
Enable the laser machines to resume work quickly and smoothly after a long vacation, we can take the following tips.
1: Safety Matters
Before operators start the inspection, it is necessary to ensure that the power supply of the entire machine is disconnected. All external water lines of the chiller are closed.
2: External maintenance
We need to make sure the power line has no obvious bends, damage, or disconnection; plugs are firmly connected; the signal wire interface is firm and not loose.
Check whether the gas hose is not damaged or blocked, and the seal is good.
The water-cooling pipes are not damaged or clogged and are well sealed. The pipe joints are firmly connected and smooth.
If the ambient temperature is too low during the inspection, such as 0°C, heating measures need to be taken to ensure that there will be no ice in the pipes.
3: Water Chiller
It should be noted that if the laser equipment is left idle for a long time in an environment below 0°C, it is necessary to carefully check whether the cooling water pipe has frozen or if there have been traces of freezing in the past. If there is icing, it is best to contact the supplier immediately to provide a more comprehensive inspection to avoid greater losses due to misoperation.
If the above checks are good, we can add pure water into the water cooler and let it do nothing for 30 minutes to check if there is any water leakage. If the temperature is lower than 5℃, antifreeze needs to be added according to the correct method.
After 30 minutes and no leakage, turn on the power of the water cooler, and keep other equipment powered off.
Open the water inlet and outlet valves of the chiller a little, rather than opening the valve completely.
After the water cycle starts, no actions for 30 minutes, observe whether the water level changes, and make sure there is no leakage in the internal water pipes.
If there is no problem with the above, the water cooler can operate normally and wait for the water temperature to reach the specified range.
4: Optical Checks
After the temperature of the water cooler reaches the set value, we can turn on the power of the laser equipment. Observe whether each indicator light is normal and whether an alarm is generated. Please do not perform laser emission or even cutting or other operations immediately.
We need to check red light, see whether the lenses are clean and center thing. If you are not sure about the steps to check lenses and nozzle, please check my previous videos on lenses and nozzle.
After above all checks done, if everything is good now, I think the machine can work. That is all our today, hoping it is also useful for you. Leave your comments below, if any questions you want to know, thank you, see you next week, bye!
Start to check out laser products: spierlaser.com
Join membership: ruclips.net/channel/UC2T9f06_5CXBogKYaIIeMDQjoin
Hello Clara, thiis is Alvaro Ibarra from Chile. I have seen your videos, wich are very educative and interesting. You give a practical aight to the operation issue very helpfull. Congratulations. I heve been looking for information about how works the laser source inside, how the laser light is created in the source. If you could explain this in some video,, I will appreciate it. Thanks for your support and help
Sorry, I could not.
Hi , how can i know the size of a part that i wanna cut?
In cypcut application
For example i wanna cut a part how can i know what is the height and weight of my cutting part?
Please help me
I suggest you checking my tutorials of CypCut, thank you.
I couldn't find😥
@@ClaraChai but I couldn't find 😥
Start to check out laser products: spierlaser.com
Join membership: ruclips.net/channel/UC2T9f06_5CXBogKYaIIeMDQjoin