![Mic S](/img/default-banner.jpg)
- Видео 58
- Просмотров 272 457
Mic S
Добавлен 2 май 2010
Chinese Diesel Heater New Controller Q & As
This is the "New Type Chinese Diesel Heater Controller" that now seems to be shipping with the Diesel Heaters. Since my last video in the functions of the heater I have been asked a heap of questions some of which I answer in this video.
My original video link
ruclips.net/video/FxzUKhDeII0/видео.html
I will endeavour to make some more videos if more questions are asked and also a video on replacement controllers, and common problems through the use of the diesel heaters
Thanks for watching
My original video link
ruclips.net/video/FxzUKhDeII0/видео.html
I will endeavour to make some more videos if more questions are asked and also a video on replacement controllers, and common problems through the use of the diesel heaters
Thanks for watching
Просмотров: 110 200
Видео
Diesel Heater New Type Controller
Просмотров 155 тыс.Год назад
After installing my Chinese Diesel Heater I found the LCD screen was different to the common one shown on RUclips. Instructions were not very clear so I went through all button combinations with help from the instructions I had to work out what buttons do what. While there is no clock display on this LCD screen, timers are quite accurate when times are set.
Wombat Friendly Waterstation
Просмотров 874 года назад
Here are some modifications to our waterstations to make them more friendly for Wombats and other larger nosed animals. It creates a larger opening by angling the 90 degree bends and then carefully cutting off the fitting that sits above the water level, When trimming the fitting make sure your saw is square to the pipe horizontally and vertically. Ensure all burs and any sharp edges are remove...
Installing and refilling your Waterstation
Просмотров 514 года назад
How to fill, install and refill your Wildlife Waterstation with some handy hints
Wildlife Waterstations A Z of Construction
Просмотров 234 года назад
Building a Wildlife Waterstation Tutorial from PVC water pipe. You can use either 100mm sewer pipe or 90mm storm water pipe. You just need to be mindful of the order the 90 degree bends go together. PVC cement will be secure after 30 seconds but it is recommended to leave for 24 hours before filling. Please remember to remove stations once they are no longer needed and keep them clean from slim...
Hypercube X Axis Issue
Просмотров 1015 лет назад
Building a Hypercube 3D printer and having issues with the X axis. When I command the X axis only to move it also moves along the Y axis. I have the bushes on the aluminium tube moving freely without binding and have checked all pulleys to make sure they are not binding anywhere but still I have this issue as can be seen in the video. I have managed to improve the performance from my initial tr...
Bass Point
Просмотров 186 лет назад
Rebuilding a Scrab Quad with APM2.5 and Gimball. This is the first test flight with the gimball, it still needs some fine tuning and failsafes all dialed in for reliable flights
Dapto May 2017
Просмотров 477 лет назад
Just a boring video of some laps at Dapto Chasing and being chased by Chris's Quad. Haven't flown for a bit so am a bit rusty
Illawarra Gyrocopter
Просмотров 1607 лет назад
A Gyro-copter flight over the Illawarra, Knights Hill, Minnamurra Rain forest, Carrington Falls, Kangaroo Valley, Foxground, Werri Beach, Kiama Coastal Walk, Kiama, Shellharbour and Windang
Building a Slim folding Saw Horse
Просмотров 7287 лет назад
I gave my last sawhorse to my neighbour so need to make some new ones. The storage area was limited so I made this pair of slim folding sawhorses in about an hour using 70x19mm timber, gang nails and a couple of hinges. Each sawhorse consists of: 1xtop 70x19x700 1xtop 90x19x700 4xlegs 70x19x750 2xbraces 70x19x700 4x gang nails 6x 30mm wood screws 2xhinges and screws 1 short length of rope
New Flying Site
Просмотров 267 лет назад
Trying a new flying location with heaps of trees Need to get the mobius tilted up for a better perspective A promising site
Bass Point
Просмотров 77 лет назад
Got the Mobius out of mothballs and tried to get some footage following a wing. Harder than it looks. Top day for a fly though
Mic's CNC First Cut
Просмотров 548 лет назад
Our newly constructed CNC machine using plans from buildyourcnc.com Geko540 controller Nema24 steppers Mach3 Cut2D 4 Axis X&Y axis belt driven Z axis Trapezoidal Rod Dell Laptop with Parrallel port
Barracuda 10k
Просмотров 1,1 тыс.9 лет назад
Another test of Barracuda10K V Hydrochloric acid. This test is over several jobs and different bricks so is quite comprehensive. The information I have received from the distributors of B10K is that it dissolves 10x more mortar than HCL but as can be seen from the results of this test, it has not been the case on these samples.
I now have a 24 volt power source, is there someway to change it to 24 volts?
It is supposed to be automatic
Thank you for the great video. Am I correct in assuming that I cannot set the on timer and the off timer to work in succession. For example, I want the heater to come on in 1 hour for then turn off an hour later when I am away from my caravan. I might want to do this if I know it will be freezing tonight and I want to heat up the interior for a little while in the middle of the night. It looks like I can only activate the on time timer when it is not running and the off time timer when it is running but I need to activate each of these manually.
@@backdoc94 that is correct
How do you change language on controller; as mine is in Chinese
Please, how to pair the digital remote to the controller?
@CmteGrana see my other video. It explaines it
Anyone know if there is a paper version on all these functions but great video anyway
There is nut hard to understand
For 2 years i have been cooking in my van, always set temp but had it on manual mode, temp would go up to 30c + but now in automatic mode i set temp to say 15c its comfortable even though goes a little higher, great video thank you
my controller lcd not bright hard to see indaylight?
Wire kaunsa use kia for soldering? How much mm
Brillent video just what I was looking as most videos are the other controller thanks! :-)
I have this same manual control. The system seems to be running ok, however the display never shuts off. It is drawing a small amount of power from the battery constantly. Does anyone know how to shut it off without disconnecting the battery? Sorry, I don't mean when the heater is running ... I mean when the heater is off and has not been used for some time. Suddenly the display is lit up even though the heater has not been used in a couple of months. Or was the screen always on and I couldn't see it in daylight?
No you can't sorry. The draw is minimal when dimmed
Is it possible to program more than one remote?
Not sure sorry, never tried. If you have 2 remotes try it
How do you turn the screen off please
You can't. It only dims when not in use
On this type of controller do you know how to put it into Hz mode as i need to connect it to a separate water heater controller
See my other video
Hi the heater i have is the upright all in one,its up and running but i, struggling to set the thermostat so it switches off at say 20c, help cheers.
Can only switch off after a set time, not available for temp switch off
@@2005mic ok so I need to set the clock and use the timer to turn it on and off at set times. Thank you have to set the clock first. Cheers for your help 👍.
You can only set 1 timer. Either on timer OR off timer. Not both
@@tarsneyisleestrelas4659 this model has no clock, just a timer. You can only set it to go off after a set amount of time, if its running. Or to come on if its not running, but not to come on, then off, only one at a time, I know!!
Witam bardzo dziękuję za instrukcję co i jak ustawić bo nie wiedziałem nawet ja sparować pilot ze sterownikiem w nowym kontrolerze. Pozdrawiam!!!
I have an e: 01 code coming up every now and again what’s the problem?
www.aclsretail.com/support-request/heater-error-codes
Hello, my screen is flashing E-09 and F1 apparently it’s a glow plug issue. Anyone know how to fix this? 🙏
Do you know, is possible to use heater only as fan? In summer, for air circulation and cooling. Thank you.
No it's not. Only as heater
why does a red circle with a red minus appear on the bottom right deisel starts then5sec trips?
Hi Mic, great video and my has just started showing E-8 while trying to start up. Do you know what this may be? All I've been able to find is E-08 in Google search. Some say fuel issue? Can you enlighten me before I lose my sh#t. Cheer
When it errors out with E-8 it doesn't show the red triangle in the top right corner like in the secret menu.
www.aclsretail.com/support-request/heater-error-codes
Thank you great video
Same control panel as I've just received, did you manage to pair the remote please as I'm having no joy what so ever 🤔
Found it in your other video 😂 thanks mate as all up and running now 👌
@captainsensible3570 no worries im pleased the video helped
@@captainsensible3570 what video 😅 same problem
Can you fine tune the fuel/ fan ratio on this controller?
No you cant
Please help. I have the exact same model as you and all of a sudden it turns off after blowing white smoke and saying error 8. When the inside case is heating it used to go up to 100degrees but now it doesn’t go any higher than 46 degrees. I don’t know what I’m doing wrong
Error 8 is lack of fuel. You need to check all lines, ensure fuel is primed to heater, glow plug is working correctly
@@2005mic it still had a little bit of fuel in the tank left but I could see plenty of fuel still in the line as it was priming. Do you have any idea why the internal temperature only gets up to around 40 degrees now
@@Ryderamazing fuel may be contaminated with .moisture. must have plenty of fuel in tank
hi , how long did you have to prime before the fuel reached the pump ?….also I have the blue controller and it appears to do exactly the same functions as your black one and the little blue icon by the air intake is exactly the same as yours but there are other blue controllers that function differently with a slightly different icon .
They self don't prime that well. You need to get the fuel to the pump, then prime from pump to heater
THANK YOU🙏
Hello! is it possiple to use that "mountain" set for lower fuel consuption in sea level? its 1,6Hz for mountain and sea level 2Hz. beacause to me that regular "H1" mode is too efective.
The mountain setting is for high altitude where there is less oxygen. Hence to keep fuel air mixture correct. Useing it at lower altitudes will result in a lean burn resulting in shorter heater life
Danke ,,👍👍👍
Excellent informative video. I was on the verge of goin to check into the nutty ward before i found your vudeo an realised I'd bought a heater with the new but looks the same controller. Much Love 😂
😈👍...Hi..I bought it for my garage, it works great,.thank you.!!
Are these controls interchange with the new one that has 3 buttons ?
Haven't seen the 3button one so not sure
how i can reset the remote control pair for use in another identical display?
Just pair it on the new one
Very clear and informative. Many Thanks
swich the motherboard to the old style
hello, is that an 2kw heater or an 5 kw - the temperatur of the heater from me just goes to 120°C yours to 178 °C - i have a 2 kw is that so low normal? ng
It's the 2Kw
Ank you. It must be a failer by mine one. How much is your temp. Of output of air
Clear as mud
Legend! Thank you so much for this man! So so helpful!
No light on control unit ?
Anyone know how to change it to Fahrenheit?
Can’t be done on this controller
Great video! Makes it sooo much easier to understand. I have a question re: new style controller. Mine has an extra button between settings & ok buttons that looks like a fuel icon - any idea what it is for?
No. Haven't seen that one yet
Any thoughts on why my power on off switch won’t work. I have to keep insert /remove the battery to start /stop👎 I used to on off with the remote but since changing the battery in the remote the remote doesn’t seem to talk to the main controller
Don’t mean the battery I mean I have to insert or remove the fuse to start stop
See my other video. It explains how yo pair the remote
Thanks for the video. Good info!
Awesome video. On this stuff i prefer an older grown up person who uses a pointing stick to make sure u cant get it wrong. No clickbait easy explanation keep up the good work please ❤
Woooow amazing video. No clickbait no ads spamming. A great intro with the times explained. I just knew this was not kid that made this video. Very very very nice. Straight to the point. Great explanation. ❤👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍. Realy these days u dont find a lot of videos like this. Great job 👍
E-2 error. my first battery wasn't strong enough for the glow plug. i switched to a big car battery and no error. hope this helps.
E-2 error - i tried using a small deep cycle battery that couldn't energize the glow plug properly. switched to a big car battery and no error. hope it helps.
The new remote control with OLED display has 2 x AAA 1.5V Micro LR03 cells. WTF A27 or A23 that annoys everyone. OLED display remote control (433Mhz) should be / is compatible with the new controller according to the operating instructions. It is cheaper to buy an OLED display remote control than A27 batteries. I use two old 1,2V Ni-MH... Thank You for the Video!
I just had one fitted today and I have the same interface, great video and very helpful. Thank you!
Cheers pal just got mine up and running in 10mins thanks to your tutorial 👍
Stare at the fan symbol, which way does it rotate? Then think it turns other way....and it does, weird.