Видео

@@alexandergennaro8596 ah good to know didn’t know that when researching. This is a temporary fix since I plan to fix my heater core later

Thanks!

😎

😎

@@alexandergennaro8596 nice that’s a good deal for all the hoses

@@Wicked.official no you don’t need forged internals to turbo your Miata

Thanks! It was alot of work but it came out great and my friends car is now protected for many years ☺

My 4Runner doesn’t have steering wheel controls.

Thanks!

Thanks!

Yeah the lenses are still in good shape. Still look pretty much new after 2 years

It should work to take the crank bolt out as well. I did test it off camera and was able to take off to bolt after torquing it

The test pipe is definitely a sweet piece! Great job on the welds and it fit up perfectly! Look forward to see the parts you produce for Miata’s in future 🤙

I took the bolt all the way out when I did it

👍

You should contact the seller. Mine came with eh Toyota emblem when I ordered

Glad this video helped you! The squeak could be caused by a dry belt. Not sure how to fix that but definitely check the tension on the belt and possibly add some lubrication to the belt.

@@wils_builds well for one thing I’m confused on how far does the tensioner bolt need to be in?

@@raulzamaniego2457 there’s no specific distance it needs to be tightened. Just enough to where the belt is tight and no slack. A trick I’ve seen is spraying the belt with WD 40. You could try that

Yeah it charges it. But super slowly. It’s mainly just to connect for Apple car play

Nice. I ended up modifying the hose by adding another that bends 90 and connects to the GM hose with a barb fitting. Looks pretty much like the cobalt hose they sell. Had to do it for better fitment with the IC piping

Glad this video helped you figure that out. I think the heater core may have been leaking on yours to the previous owner probably bypassed it

Thabks!

Yo, thanks for watching! I’ll make a follow up video soon about the headlights. So far they’ve help up really well. Still look new, no moisture in the lenses, and the LED strips still working

Hey dude, glad to try to help. Are you talking about the bolt that goes into the seat belt mount? Or the 3 holes you have to drill?

@@wils_builds for the seat belt mount!

The one you gotta drill inwards since you're not using the outer position anymore

@@magicwaffl3z I didn’t have to drill anything for the seatbelt mount. There was already and existing threaded hole when I installed my seatbelt

​@@wils_builds I'm referencing the hole you made at 10:48

Yeah it’s not necessary to weld it but many do for extra insurance since the hole can expand when pressing out an old ball joint. I’m sure just a c clip would probably be fine though

Awesome! Glad it helped you

I probably will eventually 🤙

It’s synced through USB

Awesome, thank you for the quick response!

@@ryanc0017 I think there are Bluetooth adapters you can add that plug into the USB. So that’s an option too

They’re sitting in my shelf

Thanks!

Just used to clean up the existing thread

@@wils_builds thanks for making this video, it’s very helpful and I’ll be replacing mine using this as a guide!

Your welcome 🤙

Yes this was with a coolant re route. It can also be done without a coolant re route as well.

@@wils_builds thanks 🙏

I did not set camber and caster since I’m going to get it professionally aligned. But for those that are wondering. I made a mark on the subframe and used the mark to put alignment back to where it was set before the install.

Hmmm not sure. Maybe try to consult the FB groups or forums. Someone might be able to help.

10mm

2.75 front, 2 inch rear

I believe it should be the same. The NB have different lower control arms. But definitely do your own research to confirm 👍

Glad you liked it!

Glad it helped you!

M

About 250 each side without the lowers and about 500 total. If you include the lowers, ball joint, and lower bushings then it was about 750

I haven’t driven it but I have sat in it and the visibility is still good. The X does cover the lower edge of visibility if you have a hard top but you can still see out of most of it

@@wils_builds thanks!!!

Thanks!

I bought the LED bulbs separately. There are links in the video description

I’m glad my video helped! Hope the install goes smoothly for you

That’s insane! Hope this video helps you save some money!

I’m using an impact wrench

I just kept turning the bolt counter clockwise until it fully came out. It took a while. Probably 15 mins. Couldn’t fit my impact in there so had to do it by hand. Really pain

Tell me about it was having trouble until I stumbled across your video appreciate the help

@@user-eo5rb7mq6n no worries dude 🤙 glad it helped and hope your install goes well

Glad you enjoyed the video! I hope the install goes good for you dude!