Видео

there is no camshaft sensor on the 2006 2.2 it is part of the ignition module and is called wasted spark ignition, which has a primary and secondary coil. When the coil senses a mismatch in certain conditions it will trigger misfire. There is a crank sensor and a oil pressure sensor above the oil filter. I felt like i would explain this since it took me forever to find this correct information. I had these codes and poor running and then no start which actually turned out to be a dirty MAF and throttle body that was causing the butterfly valve to stick closed therefore suffocating the motor. I replaced all these ignition parts as well with delco and still get a code every 12-0 miles or so but it seems to run fine. I have a feeling the timing chain is stretched or I have a intermittent faulty injector. Easiest was to start troubleshooting this code is if you have a code that points to one of the banks swap the coil packs and see if the code follows the swap. I haven't finished troubleshooting yet but i will post solution when i do for anyone that may be interested.

I have a 08 caliber. When ac is on its only cold on the passenger side. The driver side is warm..what is the issue!? Been trying to look for a fix. I only see one blend door actuator on the passenger side.. but cant find the other one one the driver side. HELP!

Dude, honestly I don’t understand the point of you uploading this video, your camera skills are from out of this planet.

Thanks for the video but poor quality music very distracting

What codes did you have

Helpfull video! But please make sure you drain all the air out of the system before you try to remove the purge valve, otherwise it will shoot the purge valve out straight into your face

does this actuator impact vent changes also or just temperature changes? My airflow is stuck on floor and dash but changing from hot to cold works just fine.

Great job, great video

Thank you so much! The instructions that come with the kit aren't very detailed and you did a very good job of showing position and placement of everything. Definitely got me out of a bind.

This music should be official music of all American mechanics. 😂😂😂

Thank you. I’m struggling with putting the snap ring in but your video was a huge help!

Thank you

Thank you so much. Very helpful video. Where did you buy the kit from?

Thanks for the info. I was happy that my phone has a volume control so I didn't have to listen to the music. Hahaha

Does ecm needs to be recalibrated after installing new 7th injector or is it just plug it and drive

Very impressive video 🎉🎉🎉🎉

The problem is put back all small pieces on this puzzle

Hi bro Can you tell me about size or part number this gaskets Thanks.

Great video much needed and much love

Great video much needed and much love

Which is Solenoid B since there is a code P0755 saying Shift Solenoid B?

What is that sliver box that was attached with the green screws that you removed first?

Copy

All due respect, this video is absolutely pointless, we need the noise on video for comparison in order for it to do any good.

Poor video quality

Great video thanks!

Great vid

What a nasty music 🤮

The cable that was loose mine is hard to move how would i replace them? Mine is the the opposite switch but it gets stuck an don’t go all the way to the opposite side. I thought it was the control but its the wire that gets stuck

Still leaking :(

A calm and captivating crime story awaits you. Join in!

Yup, thanks, genius video, no B.S. just showing how its done. Thanks a bunch. Saved me a bit of a headache knowing that frame came out first. Incidentally the plastic heat duct screws, i believe are 5/16". There hard to see.

Thank you bro!

This was sick!!!!

Do you have part number for O ring ??

Can you please link the video for the door you are referring to in the description

The yellow line below the green line is vent or what can you tell me I see mine not connected to any just piece of yellow

Could i manually turn the door until my actuator come in?

ruclips.net/video/yTnUojaL7s0/видео.htmlsi=B-p_ZGeVi2cYc5sU

😁 'Promosm'

This is the best video... Wow thank you so much

My father and I thank you with all of our heart. Middle of below freezing weather My dad's driving his truck with no heater. We followed your instructions and he is back to being comfortable thank you thank you thank you

I can't help but notice the Bob barker jail shoes

I had a 340 code and replaced the ignition control module with a gm part and temporarily the code went away. However eventually the timing chain went as per a mechanic. Any person having a 340 code should also check compression. If compression is bad might be your timing chain

Thank you. Every other video was showing people hacking the ducts to pieces.

Which is solenoid A

What kind of code reader did you use?

Now that how u make a dam video everything from start to finish fucking awesome bro !!

This video is one of the best examples of how to do a how-to video for automotive. Thanks

I have every thing out but that second screw on the black piece. How in the heck did you get to it?