Circuit update: I made this circuit by watching this video but there were two errors coming: problem 1: motor was off during the water level and turned on when water level touched all top position(red) wire. solution : don't connect the wire on nc terminal connect it on "NO" terminal problem 2: after the modification motor gets on when water goes just below top level (red) wire. solution : I exchanged blue wire with red wire and the circuit worked fine
Thanks for the input. But it would be so nice to make a complementary circuit to this which allows to protect the pump when the system is without water.
Good work. I will try myself. I have to use it with 5V supply only since I have a 5V USB adaptor and a 5V relay module. What will need to be changed or modified in the circuit if using such a 5V relay module? I have another question: I wish to show an LED light up for 5% level. How to do this? Also, when the level is below 5%, how can I attach another LED to glow (indicating level below 5%) so that when the water reaches 5% level sensor, this LED (below 5%) stops glowing but the 5% LED starts glowing? Can I also use the 5% LED as a flashing one and how? Hoping to hear from you soon.
Peace, mercy and blessings of God be upon you. Operating a home pump project through three or several levels to operate the pump and stop it automatically.
Thanks but I have two questions : I used 9v battery and it drains easily what can I do . secondly my relay keep smoking when connected to my 1hp submersible pump what can I do . plz advice
Dear author, could you please make a video in which to show how to assemble a simple transformerless power supply to power this circuit from a 220 volt alternating current. Thanks for the video!
भाई यदि आपने बाना कर प्रक्टिकल कर लिया है तो इसे सबको बताना अन्यथा किसी को मत बताना क्योकि जब आदमी पैसा भी खर्च करे और समय भी जब सफलता हाथ नही लगती है तो दिल से माँ बहन के लिये गालियाँ निकल तीं हैं भाई हकीकत मै है तो अपना वाटसप नम्बार दो फिर मै आपको बहुत सर्किट जो कि प्रक्टिकल करके देख लिये है धन्यवद 🙏🇮🇳🌺🙏🇮🇳🌹🌺🙏🇮🇳🌹🌺🇮🇳
Leds and the rest don't take much, the relay will determine that, I would say 100mA above the relay consumption, and normally relays are between 100 -300 mA
For lab tests it's good but it's not practical, you can't use DC inside water, you will end up cleaning the terminals every week....you need to use AC inside the water instead
it is not working with 0.5 or 1 H.P motor .... that's really necessary.I did it and all system burned. such demo projects only with very small DC motors.Dont make foolish to your subscribers.
2 1m resistor 1 100ohm resistor 1N4007 diode BC547 transistor Relay 6v or 12v 3 100 ohm pin 100 ohm Emmiter to Blue green red sensor wire (each) Red black wire Small water pump Transparent pipe
Да такую же схему собрать, только логику поменять на обратную: сухие контакты - реле размыкается. И два реле в последовательную цепь на одну помпу. Это если в лоб.
السلام عليكم اخي ممكن ربط المتحسس بااربعة مستويات تبدا بالصفر وتنتهي بالمئة طوافة مقسمة لاكثر من مستوى لو سمحت وتشرح طريقة الربط لو سمحت اخي العزيز لتحكم بمضخة المنزل تشتغل وتتوقف بالاردوينو بابسط صورة ارجو الاجابة باسرع وقت
Circuit update:
I made this circuit by watching this video but there were two errors coming:
problem 1: motor was off during the water level and turned on when water level touched all top position(red) wire.
solution : don't connect the wire on nc terminal connect it on "NO" terminal
problem 2: after the modification motor gets on when water goes just below top level (red) wire.
solution : I exchanged blue wire with red wire and the circuit worked fine
Thanks for the input. But it would be so nice to make a complementary circuit to this which allows to protect the pump when the system is without water.
No
Very good effort and you wish to share others also. Thank you🙏🙏🙏🙏🌹🌹🌹🌹
Thanks for uploading this useful circuit. You're an awesome guy.
Guys very IMPORTANT NOTE if your 100 omh is burning or getting crazy hot then try
10K resistor.
It will work
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
3:35 The thick wire is for AC 220v?
The world's best teacher thanks
💯 Sensacional 👏👏👏👏👏
Gosto muito de eletrônica
Parabéns você show 👍
Fantastic🤘😝🤘 bhai love ❤❤❤from odisha
what if some short circuit leaks the current through wire to the water ? is there any safety for that ? I dont think so right ?
Incredible. So many uses. Thanks
Muchísimas gracias , un saludo de Galicia , Vigo
Great!!! Thank you my boy! João from Brazil!
Welcome
Can it to pump 220 volt?
@@saidtv2710 Yes
hi. i tried to do this using a breadboard and arduino uno for a class project. it was a fail! thanks for the video and i'll keep trying
Can I use the system for submersible also?
boa tarde muito simples e bem bolado parabens mais seria interesante se dece de por 3 leds indicadores
Instead of supply line, make ground line pin 1 common, interchange 2 & 6 and use pin 7 to operate relay
Hi. Pls, where to connect dry run protection ? What are the modifications to do ?
By inserting electrodes in water would there be any electrolysis effect?
Slightly
Thank you sir bht khooob.
Kia AC 220v 1HP ki moter use kr sakty hen is pe?
Super. Simple et utile. Merci
Is it works in AC current?
my question as well ...
Sir same circuit 24 v dc relay main capisitor aur transitor kis no ke use krne h
Agar really or circuit ko 12 volt supply pr use krna ho to kia changing Karni Hogi?
Just one question why do you only show the schematics for 2 seconds
Tank you. Nice. Im from Poland.
Sir apne supply se kase jorte h wo nhi dikhaya
I wanted this type video. everyone making this circuit using PCB. This video is best
Just one question current flow in tank outlet yes or no.please experience me and current flow in tank outlet which volts.
No current flow as it is dc operated ac switching circuit
Please building the case ! Safety is number one prioryty ! ❤❤❤❤❤
👍
Good work. I will try myself. I have to use it with 5V supply only since I have a 5V USB adaptor and a 5V relay module. What will need to be changed or modified in the circuit if using such a 5V relay module?
I have another question: I wish to show an LED light up for 5% level. How to do this? Also, when the level is below 5%, how can I attach another LED to glow (indicating level below 5%) so that when the water reaches 5% level sensor, this LED (below 5%) stops glowing but the 5% LED starts glowing? Can I also use the 5% LED as a flashing one and how?
Hoping to hear from you soon.
You can do it with a diode and a relay only ,
Peace, mercy and blessings of God be upon you. Operating a home pump project through three or several levels to operate the pump and stop it automatically.
Can i use 220v AC watar motor???
Yes friend, you can use ac motor also
Nice design- recommend for to add sensing foot valve level also along with this.. so this will become also safety for pumb motor.
If I connect to the aquarium, will the fish swim belly up?
🤣
Good . But could you plz tell us what voltage you used to power the circuit. Can I use a 9v battery ?
It shows 6V to the left of pin 4. It should work on 9V, too -- but relay specs and battery life should be considered.
Thanks but I have two questions : I used 9v battery and it drains easily what can I do . secondly my relay keep smoking when connected to my 1hp submersible pump what can I do . plz advice
Kis par chalyah hai Ac par yah Dc par.
DC
How much power suppy give this circuit ?
Where are you from india? I mean which state
I make this circuit but not work why
Serve para 110vlts???
Hello, is it possible to make an electronic circuit for an inverted water pump? For example, the bucket will fill with rain and empty automatically
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
Hi, is there any protection if pump failed to deliver the water
There are many protection which can be applied .Pressure switch or flow switch etc etc .
Circuit diagram at 1:33
Circuit Kam nahin karta hai kaise
Sensor wire kitna meter se kam karega
70 to 100 Mtr. Depends on wire gauge
I made the circuit. But when the motor starts the base register of bc547 and 555 ic gets very hot. What to do ?????
Excellent, just what I need
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
Does the circuit is working or not
In put supply given by 12v DC supply was supported this circuit...
Dear author, could you please make a video in which to show how to assemble a simple transformerless power supply to power this circuit from a 220 volt alternating current. Thanks for the video!
Transformerless power supply doesn't have insulation from the main's. So that can't be use in this project
@@TechIdeasAG Then what kind of small-sized power supply can be used in this project?
भाई यदि आपने बाना कर प्रक्टिकल कर लिया है तो इसे सबको बताना अन्यथा किसी को मत
बताना क्योकि जब आदमी पैसा भी खर्च करे
और समय भी जब सफलता हाथ नही लगती
है तो दिल से माँ बहन के लिये गालियाँ निकल
तीं हैं भाई हकीकत मै है तो अपना वाटसप
नम्बार दो फिर मै आपको बहुत सर्किट जो कि
प्रक्टिकल करके देख लिये है धन्यवद
🙏🇮🇳🌺🙏🇮🇳🌹🌺🙏🇮🇳🌹🌺🇮🇳
Shi bole
Working karegaa yaa nhii jldi batao please
Sir, pani line me aate hi pump chalu ho Jaye, aur pani bangh ho ne per pump bandg ho haye aisi circuit banaiye, thanks.
please tell me, how can this be used to control a 220V 1 horse power motor/pump...? what more is needed?
Use the same relay, 10A 250VAC. 1hp draws less than 5A at 220VAC
Just check the start-up current does not exceed 10A
Can i get a circuit diagram of this ?
Anything to change if I have 12V supply ??? Thank's
You can use 12v dc without any modification
How many milliamps does this circuit require?
Leds and the rest don't take much, the relay will determine that, I would say 100mA above the relay consumption, and normally relays are between 100 -300 mA
What type of powerful relay use for 1 hp ac pump motor set. Give the full information.
Use 12V 10Amp realy
@@bhagyashreeghugare8381 ma'am i used 12 v 30 amps relay still hissing sound is comming after tank full because supply is on
@@bbiswasable use capacitor
When motor starts relay can not tolerate more than 10A..
What we have to do for this??
O relé no esquema eletrico ficou ao contrario.
For lab tests it's good but it's not practical, you can't use DC inside water, you will end up cleaning the terminals every week....you need to use AC inside the water instead
Power supply 6v ya 22v
6v
@@TechIdeasAG but here is 110v, what can i do??
Thanks ( Paulo /Brasil)
Douse it will work 9n 240 volt Ac Moter also 🙄
it is not working with 0.5 or 1 H.P motor .... that's really necessary.I did it and all system burned. such demo projects only with very small DC motors.Dont make foolish to your subscribers.
...use a more powerful relay
Mantap sahabat ku sukses selalu
How to add water pump dry protection when water tank source is empty,help me sir
how does it work in reverse? when the water is full the pump turns on, when the water runs out the pump turns off
powar kine volt a
It work properly thanks 😊
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively
🙏🙏🙏🙏
And whether ac or dc current to be supplied???
what's the power source ???
Direct 220 AC mey chaley ga
I like this and I need it
субтитры сделай . идеи не хватает или башка плохо соображает. ты же для всех делаешь
It's not working sir. When try to connect vcc to pin 8.relay will not switch properly and motor runs continuesly irrespective of water level
Hlo sir please tell me ki transitor bc548 use kar sakthe h
Yes
2 1m resistor
1 100ohm resistor
1N4007 diode
BC547 transistor
Relay 6v or 12v
3 100 ohm pin
100 ohm
Emmiter to
Blue green red sensor wire (each)
Red black wire
Small water pump
Transparent pipe
Thank you! Regards from Reynosa, México
А если вода в правом сосуде кончилась, а левый еще не наполнился? :=) Конец помпе? :=)
Да такую же схему собрать, только логику поменять на обратную: сухие контакты - реле размыкается.
И два реле в последовательную цепь на одну помпу.
Это если в лоб.
And materials required
When it's applied for use. The person using it while motor is on May get shocked.
Circuit ka daigram kaha hai vo chahiye
. 555Timer IC (1no)
2. BC547 NPN Transistor (1no)
3. 1k 0.25watt Resistors (R5, R7) (2no)
4. 22k 0.25watt Resistors (R1, R2) (2no)
5. 180k 0.25watt Resistor (R6) (1no)
6. 1M 0.25watt Resistors (R3, R4) (2no)
7. 100nF (104) Capacitor (C4) (1no)
8. 1N4007 Diode (D6) (1no)
9. LED 1.5V (1no)
10. 12V SPDT Relay (1no)
11. Connectors & IC base (4pin)
12. Zero PCB
Can any 1 explain me the working principle of this model
السلام عليكم اخي ممكن ربط المتحسس بااربعة مستويات تبدا بالصفر وتنتهي بالمئة طوافة مقسمة لاكثر من مستوى لو سمحت وتشرح طريقة الربط لو سمحت اخي العزيز لتحكم بمضخة المنزل تشتغل وتتوقف بالاردوينو بابسط صورة ارجو الاجابة باسرع وقت
Please check in metal container
Great work! Like
😊
I make same circuit but not working
Sir can i get simulation circuit sir
muito legal! vou fazer um também
Çok zekice.
This is very wise.
❤❤👌👌👍👍
Nice
It's not working I tryed this
Pls video banaye
Please give me pdf for circuit
Does not work frod
My 3 time' try again this serkit
Circuit not working
Tanks
Wooooooohooo