Fellowes Shredder Maintenance Fix - Auto Shredder not working
HTML-код
- Опубликовано: 8 дек 2019
- #Fellowes #Shredder
Opened the shredder but assembled incorrectly. Reopened and found the problem. Good learning and might solve your Auto shredding issue. Hopefully helpful.
PLEASE ONLY OIL ONE OR TWO DROPS. After making the video experience showed too much oil can create paper jam. 
Наука
Thanks so much! It turned out I needed to use a credit card to "wiggle" the paper sensor. Shredder would only work in reverse, dead on forward. Now it works fine. I did follow other instructions to run in reverse and removing paper shreds. But the credit card "wiggle" of paper sensor worked after all that tried. Probably best to clear it out so I don't think I wasted any time. So happy we have these resources. Much appreciation especially in this current economy.
Thanks very much !! My problem was exactly the one you describe, and the explanation of positioning the paper sensor worked perfectly. i have never oiled the shredder in 14 years so your advice embarrased me, and oilcan now out !
My P-35C was getting very noisy even after a good application of WD40. I took it apart and the paper sensor fell out. It wasn't obvious how it went back together until I watched your video then I got it. I put it all back together with plenty of fresh grease on the drive gears and some oil on the bearings and now it's working well. Many thanks buddy.
Thank you for a very helpful video!! I didn’t realise before I watched it that the plastic piece among the teeth is a sensor. As in your video, I had no paper jam and couldn’t work out why the shredder still wouldn’t work.
Different shredder, (Fellowes M-8C) but thanks to you, by adjusting the sensor, it’s now working again.
Glad to know this video is helping many people. Thank you for your feedback. Having used this shredder for years now, try not to oil too much. Too much oil could wet the paper clogging the shredder and cause damage. If oil, only little drops.
I used too much oil because the paper was jammed and now it's not working. What do I do?
@@IceHarvest929 hi, true, too much oil creates a jam. I was in the same situation. The oil literally soaks the paper resulting to a marshy paper on shredder teeth. I would suggest, power off, lift shredder and gently/ carefully clean teeth with a screwdriver 🪛 ( to help picking the paper between the teeth). You can also pull with fingers the larger bits. Please be careful. Try drying off the oil. Put shredder back on and shred some paper to attempt drying the teeth. You might need to use the reverse function as necessary. Hope this helps.
If you have to oil, in my opinion, only a drop or two, is more than enough.
@@lifestylelecanal9527 thanks
I waa just about to give up until I saw your video have the same make and model had it for more years than I can remember served me well would have been sorry to have thrown it out but your step by step solution solved the problem now it will probably outlast me.
thanks .
Thanks you motivated me into pulling my P-4SC apart and was able to fix my problem simply aligning the sensor again resolved my problem cheers
Thank you very much for the information. I've been using the shredder for many years and I want to keep it.
thanks sooo much for this help!!!! great it works. 2 days I had and the paper was too much, after this video I tried and its gone. thank you. I believed to order a new. saved, hahaha. thank
Thanks alot it’s working again was about to bin it you saved me money 😂
Thanks mate. Worked for me. I hate chucking things out when they can be fixed....!
True, sometimes a quick fix can save you ££. Glad it helped.
Fixed mine too, cheers!
#1
UNPLUG SHREDDER
Thank you sir you are a life saver
Note that once you have all the screws removed the two sides need to be pulled apart even though they might feel like there is still something holding them together - mine needed quite a bit of force to separate.
I dont have this exact model but (after unplugging) I took needle nose plyers to the paper pieces I saw in and a tiny screwdriver I dug out what else I could. Didnt seem like I moved much but eventually it kicked back on. There is a part inside that overheats with a good jam and that also might need to cool down before it starts working again. Good luck.
Thanks this is so helpful
Thank you fixed it for me
Good to hear
Wonderful. TY, Sir. But may I suggest that the instrumental music be lowered so that your voice is more prominent?
What if there’s no power? Can u tell me where the fuse is located? Is it visible from outside?
I love how glock makes its own bb guns and how they make them look so real ruclips.net/user/postUgkxnX9wE_Q8zvF75Y5iWzTU3Q4FlrtyGApQ , the only thing is that the slide doesn't move back. The sights and the body structure is so similar to a real handgun, fits in my hand perfectly but I actually ordered it with the 40 pack of Co2 tanks and they never arrived even though it said that they handed It to me. Was not able to test the accuracy since I didn't get everything I purchased which is frustrating and that's the whole reason why I got the bundle so it arrives together. So the Co2 tank happens to be a third party so it makes no sense to put it in the bundle if it doesn't get shipped at the same time, the BB gun arrived first then the Co2 tanks were supposed to arrive someday later but didn't, which doesn't make sense. I recommend just ordering the gun itself so you don't get the same issue I ran into plus there's no option for a refund. How stupid.
Thanks!
Our office has a model no. C-525 and the tube for the oil seems to be either clogged or needs to be replaced because oil goes in sometimes and sometimes not. Could you help. Thank you.
Hmm. Never knew they needed to be oiled. I will try disassembly and then will add a bit of machine oil. Thanks.
I am glad it helped.
Found a flat clamp, w hug ere does it go?
I had trouble with the audio and used closed captions. The captions couldn't keep up with your speech.
thank you! what kind of oil did you use? i don't have a fellowes, but i think this will help me with mine.
You wouldn’t believe it but i use Wahl hair clipper oil. But i think WD40 should also suffice. Given its a blade, I believe any cutting blade oil should work.
Never use an aerosol (i.e. in a spray can) or petroleum based product when oiling a shredder (both have ingredients that are a fire hazard with the high temperature of a shredder) , but vegetable oil is ok (any cooking oil will do), or mineral oil.
Put the oil in a squeeze bottle with a small nozzle. Run the shredder in reverse and pass the bottle back and forth ONCE, squeezing gently, across the blade opening in the top of the shredder. Continue running in reverse for another 20 seconds. A shredder should be oiled every time the waste basket is emptied.
One great product to use is Texet Shredder Oil LB- 240ML. Totally forgot I had this because I use my clipper oil more. So there you go, you have options. Also instruction for use (from Texet): 1. Apply oil to an A4 sheet of paper in a zigzag motion, Dom top to bottom and shred. 2. Use once per week or before continuous use.
@@wolfc8755 Thanks Wolf. I wasn’t aware. Everyday is a school day. 🤛
@@lifestylelecanal9527 🤜
Way cool
The tray does not want to close
Con las letras encima, no se ve lo que hace
Wow
Volume is too low.
I have that shredder
Need cheap hand shreader for compost food waste
can't understand a thing being said
1800c fellowes plastic coaster wheels for bin fall out. This is out of the box brand new. The coaster wheels fall away. They don't lock into place. What to do ?? Return it ?