A tip to seat the ferrule exactly is to slide it up the shaft by hand as far as you can then boil some water. Once it gets a little warm dip the shaft and ferrule and it will cause the ferrule to expand just enough to apply the adaptor or head from a club and will slide up with ease without damage. It only takes a dip of about 3 seconds.
Thank you. Enjoyed watching that because I'm trying to decide whether to put a new driver head on an existing shaft or perhaps remove the adapter and go with a different shaft.
I pulled it the adapter off with a golf head screwed in locked with a torch twisted slowly came off then i hand sanded it i put on 5 minute epoxy and after a year still going
To install a ferrule - I will actually abrade the shaft a little past the top of where the adapter ends. I will apply some epoxy to the inside of the ferrule and slide it in position. Ferrules can come loose and slide up - this takes care of that.
Taking length off the top end is called tipping the shaft and generally results in different characteristics coming to the shaft. Most shaft companies offer tipping instructions, but if you love the way the shaft feels and performs now, trim from the butt end
8 moths later.....are there any tips, or directions for cleaning out the adapter of old epoxy? Anything to avoid? I've heard people use drill bits, or reamers, but I'm concerned about removing material. Thanks!
I would just recommend getting a new adapter the $15 isnt worth the hassle. If you absolutely need to clean it up I would use a small drill bit and get as much as you can.
Added little note: Not a bad idea to put a tiny bit of epoxy on the tip *before* sliding on the ferrule. This gets epoxy under the ferrule and is a little added insurance it doesn't slide around.
just a gentle note, place the shaft in the puller and pre tension it a little,Use enough HEAT SO AS NOT TO PULL THE GRAPHITE OFF THE TIP AS IN THIS DEMONSTRATION.
I ordered a new shaft and a new adapter so I can leave the other one on the shaft. I didn't get a ferrule but it doesn't look like there is on on the original ether ? Do I need to get a ferrule ?
A single ferrule cost you like 40 cents (get a package of 10 at Dicks) and really improves the look of the club...takes it from amateur looking to professional looking, and they're simple to add on.
nice video my man ... was hoping you can help ... i just purchased some irons that have adapters and i guess fitting heads ... would the adapters come off the same way on steel shafts ? thx
I have a shaft with an old tip and I want to use that shaft for a different tip, without having the shaft puller, what other way could I get the old tip off?
If I get a new adaptor will I need to get a ferrule for it? Also is there a way to put something on the bottom of shaft to stop glue going inside shaft?
Depends on the adapter. As for the glue going inside. You can cut a tiny piece of scotch tape, although if you are not using too much, it is not a huge concern.
Is it possible to remove the SDLR bolt inside the driver heads? My new shaft is .25mm too big for the screw in the head and I’d rather change the screw if possible than mess around with the tips..
@@THPGOLF it’s a 2016 Taylormade M2. The shaft came with the adjuster sleeve attached etc yes so would like to just remove the driver head screw and replace with a slightly larger one if possible. Not many pro’s in my area (Northern Ireland) who seem to offer the service of fitting adjusters
first time i ever seen anyone use shaft bends seems to me that would cut into the shaft make them weak...i know i seen people tips break off an sling clubs across the course maybe what they did i dont know
thanks for this - QQ I pulled a 3 wood shaft that didn't have an adapter, but would like to put one on. It doesn't slide on at all, is it recommended to sand the tip down so it can slide on? or are there driver adapters and wood adapters ? or are they all created equally?
@@THPGOLF its a Honma tip on a ventus velocore - it was pulled form a previous gen 3 wood. there's not much on the tip of the shaft, maybe the inside of the adapter - i'll try to clean it out with a wire brush
@@THPGOLF For what it's worth HONMA has different adapters for each head, Driver, wood, hybrid - SMH. last question - does removing tips constantly affect the shaft ? IE I only have one shaft and wanted to test the #s on two different driver heads - obviously waiting the appropriate cure time, etc - but say changing the adapter 3 times - could it have a negative impact on the shaft?
@@pauliodotnet Many companies do such as Callaway getting smaller in hybrid. Does removing tips impact shaft? It can. Resin and material that make up the shaft can be altered/ruined with excessive heat. Use the bare minimum needed and a shaft puller to extract.
Depends on the epoxy you are using. Standard, yes, 24 hours is long enough. They make Tour Set which can be ready to go in much less time, but it can be harder to work with.
Hi. I have a Cobra driver. My Q is.....!.....What is the lowest loft/degree adaptors can be set to. Believe me!....I need a 5° loft. Yes five degrees. Lets not argue. Bryson de C use a 5.5°......probably custom built by Cobra. If you didnt know.....The late Calvin Pete who held driving accuracy nr.1 spot for 10yrs used a 4degree driver. I naturally hitball high. So I loose a lot of distance as result. Higher equals wider.....fact! Lower goes straighter!
We would recommend a fitting. Loft plays a role, but so does a number of other things. With that said you can find some lower loft tour stick heads. Check out the People’s Clubs. Tell them you heard from THP Golf and you will get a discount too.
Never tried the Gorilla Glue option, but have used JB Kwik Weld. It has a 2451 psi which is normal for golf clubs. Their cold weld is about double that and would work, but getting heads off would be near impossible.
We have multiple things in our lab. Normally all devices are Mitchell as we love their quality. The shaft puller is actually a Reverse Thrust Puller from Golf Mechanix
In modern shafts, this is much less important than people think in our opinion through a lot of testing. If this is a concern, a place like Club Champion can offer PURing.
A tip to seat the ferrule exactly is to slide it up the shaft by hand as far as you can then boil some water. Once it gets a little warm dip the shaft and ferrule and it will cause the ferrule to expand just enough to apply the adaptor or head from a club and will slide up with ease without damage. It only takes a dip of about 3 seconds.
Thank you. Enjoyed watching that because I'm trying to decide whether to put a new driver head on an existing shaft or perhaps remove the adapter and go with a different shaft.
Well done! I've never watched this process and it's not nearly as complex as I assumed, but definitely requires some careful attention.
I find it's easier to heat the ferrule with steam to obtain the correct depth. Great video.
Oh yeah this was a great refresher as I get ready to get a new shaft into an adapter!
butane is much better flame than propane, tried them both for adapters it's the only way to go, irons propane is fine thanks for the info
"One hand is always gonna be on the shaft, the other one's gonna be working hard"
I pulled it the adapter off with a golf head screwed in locked with a torch twisted slowly came off then i hand sanded it i put on 5 minute epoxy and after a year still going
To install a ferrule - I will actually abrade the shaft a little past the top of where the adapter ends. I will apply some epoxy to the inside of the ferrule and slide it in position. Ferrules can come loose and slide up - this takes care of that.
Much appreciated. Nice explanation. I feel comfortable doing mine now.
I liked your head puller what brand and model is that?
Thanks for the straightforward presentation. Too many characters on youtube.
That is our goal, glad you enjoyed it
Hi , I want to shorten the shaft by 1” and fit a different adapter. Can I take 1” off the adapter end to save changing the grip?
Taking length off the top end is called tipping the shaft and generally results in different characteristics coming to the shaft. Most shaft companies offer tipping instructions, but if you love the way the shaft feels and performs now, trim from the butt end
8 moths later.....are there any tips, or directions for cleaning out the adapter of old epoxy? Anything to avoid? I've heard people use drill bits, or reamers, but I'm concerned about removing material. Thanks!
I would just recommend getting a new adapter the $15 isnt worth the hassle. If you absolutely need to clean it up I would use a small drill bit and get as much as you can.
Use a hosel honing wire brush bit.
Does the ferrule need to be as tight fitting as that?
Thanks for your vidéo.
Is it possible to use again the old adapter after de manipulation ?
Its possible, for some, but it is a tough go for a lot of people.
@@THPGOLFOk thanks a lot.
What is the name of the vice you using to remove the tip and what other alternatives are there outside of the vice ?
We use a Shaft Puller for almost all removal where graphite is involved. Currently it is the Golf Mechanix Reverse Thrust puller.
When you buy a new adapter does it come pre prepped or is sanding needed?
We almost always use a drill and rough attachment to prep it. Sanding would be fine.
Added little note: Not a bad idea to put a tiny bit of epoxy on the tip *before* sliding on the ferrule. This gets epoxy under the ferrule and is a little added insurance it doesn't slide around.
Hi. What brand of shaft puller is that? I searched Ebay and Amazon and did not see it. Thanks
The THP Lab uses the Golf Mechanix Reverse Thrust Shaft Puller
Its a Golfmechanix shaft puller model 210908 reverse Thrust model
just a gentle note, place the shaft in the puller and pre tension it a little,Use enough HEAT SO AS NOT TO PULL THE GRAPHITE OFF THE TIP AS IN THIS DEMONSTRATION.
Great video! Very informative. Would "standard" 50/50 epoxy be strong enough, with a day to cure the glue?
Never tested it, but it should. Recommend trying one club first.
I ordered a new shaft and a new adapter so I can leave the other one on the shaft. I didn't get a ferrule but it doesn't look like there is on on the original ether ? Do I need to get a ferrule ?
Ferrules are for aesthetics only, you are okay.
@@THPGOLF Thanks for confirming that so quickly. I checked my driver and 3W today and neither have a ferrule.
A single ferrule cost you like 40 cents (get a package of 10 at Dicks) and really improves the look of the club...takes it from amateur looking to professional looking, and they're simple to add on.
Great tutorial! How did you slide ferrule further down shaft tip when you went off camera to place at desired location prior to adapter set?
Force, but there are many ways including using some heat. Putting them in warm water is an easy method.
Was referring to technique. I assumed you used the adapter to push ferrule into proper position by tapping it on a hard surface prior to epoxy?
@@bahsheep6817 Correct. Slightly warm ferrule and then we have a small cement block next to our work station in the tech studio to tap down.
I failed getting the old F9 Hosel off without a shaft pull. Guess I have to ask a fitter to do that for me :-(
nice video my man ... was hoping you can help ... i just purchased some irons that have adapters and i guess fitting heads ... would the adapters come off the same way on steel shafts ? thx
Possibly. They can come off for sure
@@THPGOLF thx for the reply ! much appreciated !
I have a shaft with an old tip and I want to use that shaft for a different tip, without having the shaft puller, what other way could I get the old tip off?
Assuming it is graphite, tip removal requires hit and force, without the force of a puller too much heat would have to be used to remove.
If I get a new adaptor will I need to get a ferrule for it? Also is there a way to put something on the bottom of shaft to stop glue going inside shaft?
Depends on the adapter. As for the glue going inside. You can cut a tiny piece of scotch tape, although if you are not using too much, it is not a huge concern.
I know you said you normally dont use glass beads but can you use sand instead of glass beads for centering?
Possibly, although you would need similar sized grains in our opinions.
Where did you purchase the golf shaft extractor?
We have a few. The Golf Mechanix is available at most places that sell components. It is the reverse thrust model.
Are the rings on a Callaway adapter plastic or metal? Do you take them off before heating the adapter?
Plastic. Trying to save adapters is not something that we do, although some do.
Is it possible to remove the SDLR bolt inside the driver heads? My new shaft is .25mm too big for the screw in the head and I’d rather change the screw if possible than mess around with the tips..
What shaft and head are you speaking towards? Is the shaft prepped?
@@THPGOLF it’s a 2016 Taylormade M2. The shaft came with the adjuster sleeve attached etc yes so would like to just remove the driver head screw and replace with a slightly larger one if possible. Not many pro’s in my area (Northern Ireland) who seem to offer the service of fitting adjusters
what shaft puller is that
?
first time i ever seen anyone use shaft bends seems to me that would cut into the shaft make them weak...i know i seen people tips break off an sling clubs across the course maybe what they did i dont know
Shaft beads will not cause breakage
The make sure that the shaft is centered in hosel or adapter.. I recommend them ...
How much play, or space is there allowed between shaft and adaptor when shaft is in adaptor before adding glue?
Should not really be any
Did you ruin the older (previous) white shaft at the beginning with too much heat? The graphite "fur" didn't seem right after you pulled the adapter.
Nope it was good
Will any old epoxy from the hardware store do? Or do you need golf specific stuff?
Specific golf? No, but it’s safe. It doesn’t cost much more and we recommend using Mitchell or Brampton
What is the make and model of the shaft puller in this video?
Golf Mechanix reverse thrust
thanks for this - QQ I pulled a 3 wood shaft that didn't have an adapter, but would like to put one on. It doesn't slide on at all, is it recommended to sand the tip down so it can slide on? or are there driver adapters and wood adapters ? or are they all created equally?
Can you provide more info? What shaft and what adapter? Is there a large amount of epoxy still on the shaft after pulling?
@@THPGOLF its a Honma tip on a ventus velocore - it was pulled form a previous gen 3 wood. there's not much on the tip of the shaft, maybe the inside of the adapter - i'll try to clean it out with a wire brush
@@THPGOLF For what it's worth HONMA has different adapters for each head, Driver, wood, hybrid - SMH. last question - does removing tips constantly affect the shaft ? IE I only have one shaft and wanted to test the #s on two different driver heads - obviously waiting the appropriate cure time, etc - but say changing the adapter 3 times - could it have a negative impact on the shaft?
@@pauliodotnet Many companies do such as Callaway getting smaller in hybrid. Does removing tips impact shaft? It can. Resin and material that make up the shaft can be altered/ruined with excessive heat. Use the bare minimum needed and a shaft puller to extract.
That's way too much epoxy
what grit to use if going the sand paper route to prep the shaft?
Fine, so you do not do damage to the shaft.
How long does this need to dry, before playing? Is 24hrs long enough?
Depends on the epoxy you are using. Standard, yes, 24 hours is long enough. They make Tour Set which can be ready to go in much less time, but it can be harder to work with.
What brand of shaft puller did you use for this video?
Golf Mechanix reverse thrust puller
One of the reasons I hate graphite shafts (in irons). One and done. Steel shafts (Dynalite!) you can pull them very easily and re-use.
Here's how I added an extender to 9 golf clubs. Dick's credit card. No I'm serious. I applied for one and Dicks did the work for F-R-E-E. $41 VALUE.
my new adapter is getting pushed back off the shaft
Hi. I have a Cobra driver. My Q is.....!.....What is the lowest loft/degree adaptors can be set to.
Believe me!....I need a 5° loft. Yes five degrees. Lets not argue. Bryson de C use a 5.5°......probably custom built by Cobra.
If you didnt know.....The late Calvin Pete who held driving accuracy nr.1 spot for 10yrs used a 4degree driver.
I naturally hitball high. So I loose a lot of distance as result.
Higher equals wider.....fact!
Lower goes straighter!
We would recommend a fitting. Loft plays a role, but so does a number of other things. With that said you can find some lower loft tour stick heads. Check out the People’s Clubs. Tell them you heard from THP Golf and you will get a discount too.
You need a 1 degree loft Driver big guy. Special order it.
Can you use JB Weld or Gorilla Glue versions of epoxy?
Never tried the Gorilla Glue option, but have used JB Kwik Weld. It has a 2451 psi which is normal for golf clubs. Their cold weld is about double that and would work, but getting heads off would be near impossible.
Thanks! Was planning on using to attach an adapter. I’ll try the lower psi version
Why didn't you put a bit off glue on the shaft so the ferrule gets glued too
Some people do, others don't. hasn't seemed necessary in our testing, but understand that some prefer that.
@@THPGOLF I've done it both ways I've found after a while the ferrule moves up if not glued as well better to be safe then sorry
What powder is this in the mixture ?
Beads for centering.
@@THPGOLF Thanks
do i have to use those shaft beads?
Not at all
@@THPGOLF you da man thank you
What is the white powder called?
Shaft beads
Don't sniff it.
only one thing what kind of epoxy did you use
Mitchell Golf Tour Set
Followed is mostly but still too complicated to try and do on my own.
Once you do one or two or practice on plain plastic it’s a piece of cake. Promise.
has anyone tried boiling a few inches of water and dipping the adapter into it for a minute or two to remove the adapter?
You will need more heat or pressure to remove. Leaving it in there too long will break down the resin and ruin the shaft.
Can you use any type of epoxy
For the most part yes, but we recommend a few different ones on the forum.
Any golf club epoxy works.
Can I ask the type of shaft puller you use and where you got it?
We have multiple things in our lab. Normally all devices are Mitchell as we love their quality. The shaft puller is actually a Reverse Thrust Puller from Golf Mechanix
Biggest question I have is "how to set it to the flex of the shaft?"
In modern shafts, this is much less important than people think in our opinion through a lot of testing. If this is a concern, a place like Club Champion can offer PURing.
Way too much epoxy