Bend deduction in reinforcement steel is totally wrong | Practically proved | Engineering Tactics

#EngineeringTactics #BendDeduction
Bend deduction in reinforcement steel is totally wrong.
Practically proved.
Steel bend deduction formula
45° Bend 1D stretched
90° Bend 2D stretched
135° Bend 3D stretched
All are values wrong.
Engineering Tactics
Follow me on INSTAGRAM: / technomembers
FACEBOOK account: profile.php?...

[@Rockys-hm2oz]

😁😁😁 ab samajh main aaya ki site par aour office main baithhkar kitna fark hai...by the way achha laga ye tarika ...i give you 100 marks

[@imadkhan2644]

Hi, it is a good attempt but there are two mistakes in your analysis.
1.As per IS 2502 minimum bending radius should be kd i.e 4d for HYSD. So for 10mm bar you should use 80mm dia bending pin at center to get accurate dimensions.
2. We deduct 2d or 3d from total length of bar taken from top of L to bottom of bend and face of L to end of the bar.the bend of reinforcement is not perfect 90 but a curve so we need to deduct (k+1)d × 2 and add 0.5×3.14×(K+1)d.

[@dhruvmistry6956]

Hello sir, I am having doubt in this concept. Can we please have a talk on call?

[@qamarzaman5319]

U are right

[@manojahire3429]

The deduction of 2D has to do with the Measuring concept when applied to the BBS. Its Deducted on the BAsis that the measurements we note down in the BBS is the Nominal Cover measurement. so what u got is half. Double all your increase in length and then check ..its perfectly 2 D and 3D.....IF the Measurement was to do with Centre then no deductions' would have required.

[@faizanraj8937]

You are completely telling about theory...... Actually he is telling right.... this should be apply for any measurement of respective steel dia .... No matter it is straight, curvy in shape... If you are bending 45°-1D, 90°-2d, 135°-3d, should be proved by theoretically......

[@faizankhan-pd9ck]

same problem I've faced today... cutting length is different from actual

[@UnknownStatus11]

New formula for 90° L - 2D/2 😊
Tahank You ... .

[@sunilbhakat5699]

Nice analysis on measurement🙏🏾

[@jagdishpant7639]

Very Good practical shown. Thank you

[@jaydalvadi9090]

Yes you are right thumb rule is not true but result what you tested is also differ when brand as well as type of steel changes I also tested on my site.

[@ENGINEERINGTACTICS]

Good

[@biswajeetpanda2388]

Site temperature and ductility of steel makes difference

[@ChangmaGoppoKarbari]

Suppose if you a make a square stirrup, you need to bend 4 x 90 degree bends and 2x 130 degree bend. In such case cut length will be, say 2x2D+3D as per your demo. E.g. Deduction length= (10mmx4)+(15mmx2) for using 10mm. Dia. rebar. Am I right?.

[@hiteshkannpariya]

Its practically information given❤️

[@sunandanarwade655]

Nice practical video but steel ka grade kya hai ?, Plz specify. Elongation is subject to grade of steel.

[@Infraupdate]

Steel kun sa hai mild or hysd, Tmt

[@esrafilansari7087]

Hysd

[@mesdelhi8078]

Bhi jabrjasttt itnaa behatreen kamm kar rhae ho aap na thnx bhi upar wlaaa aap ko barkat de bhii

[@ENGINEERINGTACTICS]

Thanx bro...For this lovely comment

[@ehsanamjad257]

Great practical guide 👍👏

[@ENGINEERINGTACTICS]

Thanks

[@pradeepkumarpati7651]

Bro you have taken outer length but actually if you take inner length and take the mean length then you will get no change in length.

[@qamarzaman5319]

Measurements should be taken in 90 degree. Not aligned with bar.

[@shahzadasalim8625]

To fr kis hisab se cutting hoga jo shi ayega

[@sreedharbhuduru6125]

very rare topic, best attempt.

[@singh_11tours22]

Etana difference hy toh phir kaise kiya jaay BBS, and ring ka cutting length find karne ka sahi tarika kya hy plz suggest me the right solution

[@wonderingcivil8808]

Informative

[@chhotelalpaswan1742]

90 aur 45 deegri ka bend karane ka liye pin setting kaise kare bataiye

[@Durgeshkumar-ip1ls]

Thank you sir

[@deepakshuklapandit3190]

Good information sir👍

[@vinodkarle2630]

धन्यवाद.सर.

[@er.krupasindhubhoicivil8896]

Ring me centre line length nehin badha hoga mere hisab se.aap ring ke outer edge se napi lie hai, inner edge se bhi napi kariye aur center line length ko bhi.

[@ENGINEERINGTACTICS]

Maine outer line se measure kiya fir bhi wo 2D ya 3D ke hisab se nahi mila usse kam mila...Socho agr centre line se measure krta to abhi jitna difference aya h usse bhi zyada difference ata....Outer line se kiya half value mil rahi h 2D ki...Agr center se nikalta h to half bhi nahi milti

[@savansolgama3087]

@@ENGINEERINGTACTICS yeah or inner age measure karte to use bhi less ata

[@CivilEngineeringEdu]

Nice explanation sir ji..

[@punyachaudhary3253]

Your measurements is only in handy elongation length. I think which is not match in practically placing length in actual structure.

[@abhilashsonawane6035]

Thank you sir 🙏🏼🙏🏼🙏🏼🙏🏼

[@Er.dvndrkumarcivil]

Ring inner L. B. +2 hook... Acutal cutting length... Li hogi

[@maqlala6072]

I need this type of bending machine

[@manojahire3429]

may e expert nahi par...it has to do with the Setback, mold point and K.......higher the Degree of Bend higher the Setback...higher the deduction....SB= MT+ BR.......k..tan(0.5@)

[@manojkumar.a617]

Thanks bro

[@parwindersingh3233]

Thanks bro ☺️

[@s.s.polymers]

I'm supplying plastic wilding rods

[@sourabhsana2864]

YE MACHINE KAHA MILEGI
PURCHASE KARNA HAI
KOI CONTACT DETAILS ?

[@Ekatibhasa]

Nice

[@sourovsaha1086]

But u measured the outer surface.. whereas u need to measure the center line.. accuracy cannot be achieved by any means..

[@rashidgavit2272]

Bhai ye 90 degree is equal to 2d kyun ata hai kuch derivation hai kya

[@Creativeboy57]

Bhai to iske liye kya kiya jay

[@arunmalhotra5040]

Circular ring me kitna bend deduction krte h??

[@navedhasan3253]

Do kerne padege jitne degree bend karoge

[@amangraphics]

yahi fark hai pahdai aur experience me..

[@bhataadil7191]

Sasta engineer😎😎

[@shubhamsoshte3447]

45° bend karke dekho na sir

[@Ajit551kumar]

2d 3d method Wong hai ise use nahi karna chahiye sir

[@neerainbhandari1764]

Steel MS h ya HYSD??????

[@ENGINEERINGTACTICS]

HYSD

[@Rock-xw1ty]

Sahi tarika

[@gunalimmgatla2499]

That is only more than 16 dai

[@pontubiswas8781]

2D formula thik hai but apka mapi korne ka tarika sai nehi lagrahe

[@sanketkadam8063]

Bhai pahila 230 hi aa raha tha

[@Arunkumar-ok8yy]

Mota baar ko test nhi kiya please

[@qamarzaman5319]

U measure it wrong

[@Jaspreetoriginals]

tera steel khrab h

[@keenmmbkeen3541]

Beta theory phir se padho tab practical karna

[@climaxmovi222]

Beta ye practical hi hai ,dhyan se dekho

[@banwarivlogs8924]

बकवास बहुत करते हो

[@shahzad1201]

Sar aapka contact number chahie

[@biswajeetpanda2388]

Site temperature and ductility of steel makes difference

[@wonderingcivil8808]

Nice