How to Replace Transmission Shift Solenoid 95-10 Chrysler Sebring Sedan Coupe
HTML-код
- Опубликовано: 30 сен 2024
- In this video, 1A Auto shows you how to remove, replace and install a transmission shift solenoid that is causing your gears to stick, slip or not shift at all. This video applies to the 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06, 07, 08, 09, 10 Chrysler Sebring
Get more tips & tricks when you subscribe to our channel!
1aau.to/m/Subsc...
Buy Now at 1AAuto! 1aau.to/ia/1ATR...
Connect with us on social media!
1aau.to/m/Facebook
1aau.to/m/Twitter
1aau.to/m/Insta...
Check out this playlist for more great tips and tricks! • Tips & Secrets only Me...
#1AAuto
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
After installing the transmission shift solenoid, do you have to recalibrate it electronically?
Any answer on this??
@backander We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com 888-844-3393
2002 Sebring wouldn't shift into 2nd from 1st, reverse works, I replaced the shift solenoid like suggested and nothing has changed. Gear indicator shows I'm in all gears, neutral and park at all times on the dash... I'm lost on what to do next.
Did you ever figure out what was wrong?
We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com 888-844-3393
My 2005 Town and Country wouldn't shift in hot weather after driving a while, (P0700 code) so I went into the fuse box and replaced the EATX Safety Shut Down Relay for $20. Problem solved! Thanks, Occam's razor!
+mark crane Thanks for the feedback!
I'm going outside now to replace the one in my son's car. I am using a plastic razor to remove the gasket. Just thought I would put that suggestion on here. Thank you so much for this wonderful video. Easy and straight forward.
What woud cause a hard 3/2 downshift. I have replaced the solenoid and serviced the transmission but still have this issue. Any advice is appreciated.
We just replaced the solenoid on 04 Stratus SE. Check engine light came off but still slipping when downshifting from 4th to 3rd and 2nd gear. Check engine light said "4th gear incorrect ratio". So is it the speed sensors, valves or 4th gear itself? This why people give up and just get another vehicle. Too many things could be busted...
Hey Jason, did you ever figure it out? You described my same symptoms and also the repairs I am about to perform.
I have a question my car started not to want to shift into proper gears as driving so it pretty much stays in first gear code po760 popped up first shift solenoid sea malfunction I thought I could just replace the solenoid but the mechanic is telling me it needs a whole new transmission is he telling the truth or lying cuz I just came across this video and it looks pretty easy to change out the shift solenoid
Can you make a video or tell me where the gear shift module is located and how to change it in a Chrysler 300
is this the same process on the 2001 chrysler sebring 3.0L coupe with the mitsubishi engine?
This is a helpful video for a 2000 Dodge Grand Caravan 3.3L as well.
Thanks!
The 2.7 sludge machine!! Gotta love it...
+Andrew Oliver Thank you for checking us out. We agree that the 2.7 engines are "lovable". 1aauto.com
that was a 2.4 4cyl. not the 2.7 v6
no it wasnt,,, you must be blind it says 2.7L 24 valve engine right on the Valve cover ,, Go see your local Ophthalmologist ( EYE Doctor ) and get your eyes examined,, or go Be an NFL referee,, youll fit in perfectly :)
Is the the same for a 2004 Dodge Intrepid 2.7 ltr. V6?
INTERESTING INFORMATION: If the new solenoid has three dowel pins and the part from the car only has two, just gently tap down the one pin even with the mating surface. Also, tap down the other pins as needed to match the height of the old solenoid pins. Only ONE video of many (including this one) that I have seen talks about the dowel pins:
ruclips.net/video/AZQYn8Asl80/видео.html
Note on this video at 3:23 the old solenoid has no pin on the right, but nothing is mentioned about it.
+William J Thanks for the tip!
Thank you so much, I have been having a major problem with trying to install my new one, so I tapped down the 3rd dowel pin but didn't pay attention to the other two, will get that done tomorrow and hope that helps to seat properly. probably the other two are to high holding me up. Rookie here, big time....lol
where is the transmission control module on a 2004 sebring with the 2.7 I've looked for it but only see the computer right in front of the fues box are they integrated?
What if one of the bolts brake ?? Would I have enough room to use a easy out or would I need to remove the transmission?
Sometimes my automatic transmission wont go into drive when in D selection and when i bring it into manual shift mode it will indicate it being in first gear but wont move and wont visually go into 2nd gear manually, but park neutral and reverse always works, this all happens randomly when the transmission is cold or hot. When it is functioning normally it will shift into all gears very smoothly automatically and manually it will indicate going into 2nd from 1st What could be causing this?
And if i have to remove solenoid plate how do you remove it? Theres no video's on here showing how and i don't see any bolts / fasteners.
Can you make a video or tell me where the gear shift module is located and how to change it in a Chrysler 300
What are failure symptoms?
need a video of a 2004 Chrysler pacifica transmission control module removal and install
+Prentiss Hedrington We currently do not have an an auto repair video on this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future. Here's a link to our website if any of our viewers would like visit us online: goo.gl/0AyTij
This the same for a 2.4L?my sebring has a 2.4!
+Donald Whiteman Thanks for checking us out! The install should be the same or similar.
Was your car giving off check engine code P0700?
@1A Auto Parts is it the same on a dodge intrepid 2002
Can you please make a video on how to replace the solenoid pack on a 2002 dodge intrepid while its still in the car it would help me out alot and im sure all other intrepid owners
What have you done to solve this problem? 8 years ago🌚💔
AFTER installing a new transmission control solenoid does it need reprogramming or just plug n play
Did you ever find out?
look at the original solenoid it doesn’t have a bolt valve ring on the right ride like the replacement. I’ve done this job but i ended up with a huge leak
Can you tell us more about that? Did the presence of the valve on the new part cause the leak? How did you solve it?
Do I need to have a transmission flush done after doing this repair? Some people are telling me to get it flushed and some are saying I don't need it.
Bailey Gray Bodily depends if the fluid smells good not burnt and it's not black you can change the fluid
Can't find the part on your site
what is a transaxle light flashing mean?
We just replaced the solenoid on 04 Stratus SE. Check engine light came off but still slipping when downshifting from 4th to 3rd and 2nd gear. Check engine light said "4th gear incorrect ratio". So is it the speed sensors, valves or 4th gear itself? This why people give up and just get another vehicle. Too many things could be busted...
hello sir, how you doin,i have 2006 chrysler 300,2.7L V6 auto trans.but has a transmission shifting problem while in shifting on 2nd gear mostly in slow down for 20mph,,the sound of shifting its like kicking the,,please give me an idea how to fix it by my self,,im asking your consediration about this trouble..thank you and god bless you,
The problem is the gasket I have a 2009 Chrysler Town and country 3.3 and I can't get the gasket to stay in place
DO THIS WORK OM A SEBRING 2008 3.5 ENGINE . WHEN I PUT IT IN DRIVE CAR CUT OFF RUN GREAT IN NEUTURAL AND REVERSE
Thank been working on my 2002 pt cruiser and it is twice the work of your car . On mine you have to remove battery and battery tray and battery bracket which was difficult two removed from top two re
Should I start with changing input and output sensors before shift solenoid? I have a 2005 Chrysler Pacifica. Shifts really hard when I slow down and stop or when I put into drive. Also seems to get stuck in 3 or 4th fear sometimes. Codes are 700, 731, 732, and 720. Your reply would be appreciated.
Yeah, I'm having that problem tightening down my new solenoid pack, I tapped down the 3rd dowel to flush but really didn't pay attention to the height of the other two, will check that in the morning and see if it seats better, thanks for the tip, really appreciate it !!
Is this the sane thing as a TCM ( Transmission Control Module ) ?
This is what I want to know. My car is giving off code P0700 and it’s for TCM
I have a PT Cruiser that will not get out of park. It was feeling hard to get out of park a few times and I thought it was just the button getting stuck until it stranded me at the store. It will not get out of park now. I know it could be the brake light switch or something in the shifter like the cord or the part with the spring. Could it be this too? Brake lights are functioning when brake is pushed.
i have a 95 grand caravan and i have to take off slow or it will kick into neutral. if i ease into it i can get up to 60 no problem. if i am going down the freeway at 60 ish i can step on it and it will get up to 75 but no faster and it sounds like the engine is over revving but still in gear.
Would a failure of this unit cause a no-shift/falling out of gear condition when cold ? - After a few minutes (or hot weather) the transaxle shifts normally, excluding an occasionally rough 2nd gear downshift.
+MicroCarist If this unit is going bad you may experience a abnormal shift pattern. We carry the part shown in this video on our website. Here's a link to them if yours has gone bad and you need to replace it. We should have this back in stock this week. www.1aauto.com/transmission-shift-solenoid/i/1atrx00005?RUclips&RUclips&CTA%20Comment&
Hey MicroCarist you described my symptoms almost exactly. What was the issue and solution that you found?
when in park my 2006 pt cruiser JUMPS into gear when going from park to reverse or park to drive. also once it JUMPS into gear, my car will not shift pass 1st gear so i have to drive only 25 miles per hour. then there other times when going from park to drive or park to reverse, the engine does NOT jump and will drive all regular as an automatic transmission should. the check engine light is on and the code is TCM. does this sound more like a solenoid issue or a motor mount issue
I just bought a 2001 dodge intrepid n took it to autozone n they pulled codes p0700 n p1781 r they bad codes cuz I don't have a check engine light
I have a 1987 Dodge Dakota 4x4 with the 3.9 liter motor. I bought a transmission from a wrecking yard and installed it, then found that the transfer case was bad so I replaced it also. The truck shifts into gear without hesitation but will not shift thru the gears, so all i have is first gear working....why? could this be due to vacuum lines hooked back up the wrong way or leaking vacuum lines? Let me back up, does the automatic transmission in this truck depend on vacuum to shift gears? If not then what controls the shifting....help...don't know what to at this point....thousand dollars later and the truck still wont work.....
I have a1998 chrysler concorde where is the transmission shift solenoid located
2003 Trailblazer has 2-3 shift solenoid code when check engine light came on...should I just replace all solenoids at once so I won't have issues later? Its been driving great until now...any suggestions are really appreciated.Thanks!!
Make a video for transmision shift selenoide B
Elantra 2008 please
Tengo un chrysler sebring touring del 2004 y me da el Codigo p0700 y no hace cambios ya le puse nueva computadora y sigue asiendo lo mismo me podrían ayudar por favor
Video very imformative I just stumbled accross this video for this vehicle very simple and easy to do r&r thx!!!!!!!
Is this the same process for a 2000 Chrysler Cirrus speedometer won't read hiw many miles I'm. Driving or what gear I'm shifting in but it drives just limited
My 2002 pt cruiser was alot more work had to remove battery and battery tray and battery bracket. Also it's a good idea to hold all wires back with nylon ties keeping everything out of the way. The hardest part was removing the battery bracket remove two bolts from the top and the other two from the bottom. Very tight to remove the four bolts. I removed driver side tire to get to lower bracket bolts.also didn't have my iner fender liner on made it easier . Also had to remove the left and right coolant hoses & the speed sensor
After removing sensor was able to remove the solenoid. Had to release it with little effort with a pry bar.also I used a wheel ratchet with extension when removing top bracket bolts help me alot anyway Hope this helps .
hi i have a questions about this ...my QUESTION is...i have a 2001 dodge stratus automatic 2.4 an i had a transmission leak in the hose that went to the radiator i fixed it was a clamp an the leak was fixed a few days later im driving down the road an the shifting is doing fine i get to 40 miles an hour an it must shift to a higher gear at 40 whats werid is that once the car comes down in speed to 30 miles an hour i feel a KICK or pull from the gears shifting down other then that the car runs good an no other shifting problem i can tell the gear shift smooth going up just when i get to 30 when it shifts down ..... what do you think it can be or a fix thanks so much for your help ......
Did you find out the reason finally? I have a 04 stratus doing the same thing recently. Thx
Help! Replaced shift solenoid 6 months ago, now when car is put in drive, it kills the engine. Drives great in reverse. Any ideas where we should start looking?
i have code P0870 “Transmission Fluid Pressure Sensor/Switch Circuit C” i was trying to look up where is this senor or switch located on my 2008 Dodge Avenger 2.4L but got no type of help online. Recently changed the Solenoid using this video have not changed the transmission fluid yet and i have not gotten a quick learn yet but i will tomorrow. Is there any guidance you can help tell me? Thanks in Advance
I would like to know what you had to do with your problem you having with your 2008 Dodge Avenger I'm having the exact same issue please tell me what you had to do
Thank you so much
I once owned A 2004 Sebring. Loved the car. Only ever had typical repair items,, brakes, rotors. Tune up items. Anyhow great clear video. Good Audio. Well explained.
Ok so i have a 2002 dodge durango and it sounds like it is reving up really high when driving .so i was told to change the speed control sensor.so i did and it is still doing the samething?can anyone please help
The video was very informative but I'm working on a 1997 Sebring convertible and the Transmission control solenoid is very hard to get at because the air cleaner is all the way on the right and the fuses and other electronics are right above the solenoid. Do you have any video that show how to remove all of that?
What would cause the indicator to not show park or neutral which tricks the car into thinking it's in gear even if you take it out of gear
ok Matt ill do it for my self,so the first step that ican do,i change the trans shift solenoid,the trans shift solenoid is locating inside the transmission right?
i had to take my dodge avenger to shop because they said it has to be calibrated is that something I could have done myself.
I have dodge caravan 2006 code p0700 transmision control sistem its the same problem ?
How long did it actually take you to do the replacement? I calculate maybe less than 30 minutes maybe 20 minutes?
Do you have to do the transmission quick learn procedure after replacing this part?
Any answer on this?
What do you if the part won't sit evenly back on the transmission?
Can you do one on a 2008 grand caravan whenever you guys have a chance.
You guys would have 2006 jeep liberty, with a stuck key. It wont go to off. It's stuck and the shifter slips easily into other gears. The cable shifter wont return all the way back when i put in park. Would you have a video
on this?
Hi, My 2006 Town & Country gave me a 0700 code. I took it to a very famous transmmision repair shop, they ran another tool and gave a 0740 code back.
The guy there told me that the trany was about to crash and that I should repair it immediatley, with them, for about,$3K.
So I went away, did more research and learned that this error code has to do with the TCC Solenoid. Do you think that by replacing the part the issue could get solved?
Thank you.
You may want to have another shop look at it. If the fluid and filter hasn't been changed in a while, you may want to have the transmission flushed and a new filter put in. A small piece of debris floating around in the fluid could hang up the valve body or a solenoid, causing the transmission not to shift correctly on your 2006 Town & Country. Hope this helps you out. 1aauto.com 866-403-3393
great work, excellent video.
I own two sebrings, I'd like to know what don is thinking while working on a Chrysler sebring. They are hard to work on. The way the engine is crammed into the engine bay. He's probably cursing the enginers that made this car. I know i do.
+Ken Sendelofski Thanks for the feedback and watching!
does this fix p0765 and 700 codes with 2007 models?
Dodge Dakota truck 97 shift transmission solenoid
I need to replace the solenoid on a 2005 mercury marquis
hy 1Aauto.com I'm a customer of yours, great service great parts 👍👍👍👍👌, my TCM have a p0605 - p0700 it needs to be replaced , I bought a used one from the same year car, now my question is, does it need to reprogram?
or is just plug and play?
+Kg West You might just be able to plug it in. Thanks for checking us out. 1aauto.com?RUclips&CTA%20Comment&ATony
Would the location be the same on a 2000 Chrysler cirrus?
There is a lot more room on that thing than there is on the Caravan!
I was just told that i may need to change my shift solenoid on my 98 Eclipse RS. It will not shift out of second. The car use to jerk after cutting it on and shift into 2nd and stay there. Now it doesn't even jerk anymore and will not go above 30 with out pushing the gas pedal hard. Its been sitting in the drive way for a while now and i hope this really is the problem!!!
Thank you for watching. Please let us know how the repair comes out!
1aauto.com 888-844-3393
Oh wow, man!!! You are good. Thanks
Request: more transmission sensor videos please, such as all the sensor for transmission.
My girl has a PT Cruiser and the transmission will not go into the first gear when it’s cold. She has to rev the engine up and it will kick into the next gear. After driving for a bit the transmission will shift good. If I replace this part will that solve this issue?
+Franky Orozco It might. You should also check the transmission fluid level according to the manufacturer's instructions. Hope this helps you out. 1aauto.com
I have a 2002 Dodge stratus every once in a while the transmission will not shift out of 1st gear I have to turn the key off And then back On then the Transmission will shift perfectly there is no slipping of any gears There is no slipping out of gear into neutral it shifts on time every time it's only once in a while it will not shift out of 1st gear i would have to say one in every 8 key turns It does this any ideas
+Tim Stephens Thank you for checking us out. We would recommend checking the fluid, and if that is good then it could be a signal of the transmission internal components failing. 1aauto.com
hello. my 2000 plymouth voyager has (code P1782, pressure switch, circuit 2-4). is that the part shown in this video?
+viewer Thank you for checking us out. This appears to be a different switch, and at this time we do not offer it. 1aauto.com
What type of material is the seal made off can I reuse it?
Is this part no longer available?
I have a 95 lebaron but the shift solenoid i have has different pattern on solenoid and gasket if i replace it with this solenoid do i need to change the solenoid plate to or do i have to stay with older style solenoid. my cars in limp mode and will drive but wont shift going down the road it just stays in 1 gear. I already replace speed sensors. Or did prior owner put wrong solenoid on it. It was in limp mode when i bought it. Mine looks like this 1 --> ruclips.net/video/tgs56KvwHiA/видео.html
+Archie Cooper I would make sure that the solenoid is correct for your vehicle before you start modifying anything.
@@1AAuto And if i have to remove solenoid plate how do you remove it? Theres no video's on here showing how and i don't see any bolts / fasteners.
Do you have to drain it beforehand
I replace the solenoid because it was leaking oil & now my transmission shifts down on 3rd gear hard what could be the issue
After I replaced my solenoid pack mine did this too. I had to take it to a shop to do a quicklearn (reprogram) procedure. Cost me $75 but only took 5 minutes. Worth it.
Would this affect a PT Cruiser from driving forward but not going in reverse with an automatic trans?
+Thomas Robinson This could be the culprit, as it affects gear shifting in your auto transmission. Here is a link to the part if you need it! www.1aauto.com/transmission-shift-solenoid/i/1atrx00005?RUclips&CTA+Comment&CY5uPlDc
Is this the same for a 99 Dodge intrepid
hello A1 auto parts, I have a 2006 dodge grand caravan that after coming to a stop or hill it seems like it slips into nuteral and I rev up the engine it then roughly go into gear, so I replaced the in and output transmission sensors and it still is doing it, but not as rough shifting as it was or as often, Can you please help, auto zone gave me these DEM readings before I reset my board but with the new Senors installed P0732,P0700,P0733,P0731,P0846,P0841🤔 Again please help😎
@1A auto
I just completed a complete service on my '05 Caravan for the 1st time since owning it new (150K-ish miles). I am receiving the same codes AFTER I replaced filter/fluid (ATF+4). Did you get a repair for yours?
Can anybody please let me know if for pt cruiser is the same process?
It will be a similar process. +Rico Suave
Can you make a video for a 1996 Lexus ES300 shift solenoid E.
+Rudy Sison Thank you for checking us out. We will keep this in mind for a future upload. 1aauto.com
que buen video , lo que yo quiero saber es para que sirve el shift que esta abajo de la palanca de cambios de un cirrus 97 dice --- shift +, que funcion hace porque abajo 1a dice A / S, les agradezco mucho la explicacion, que me otorgen, gracias
es la funcion autostick....
I have a 2002 dodge my code said I need a Tran solenoid and no problem with it shifting
eric soles 6
I did everything to the t and the new part is leaking fluid all over, any ideas?
Check the gasket and its seated right
I got a problem with my 2006 chrysler 300c hemi. It stalls almost every-time I come to a stop. My mechanic said he's 95% sure its the transmission and it would cost almost $2000. I just want to know if you've had this problem before with the chrysler stalling? I've taken it to the chrysler dealerships and they couldn't tell me the problem
Benny Bee sounds like a bad torque converter or bad torque converter clutch in the trans
I had the same stalling issue on my 06 300c hemi. Chrysler warranteed the fuel tank as they say there is a valve sticking allowing fuel vapor into the charcoal canister that then gets sucked into the engine when the purge valve opens. I found even with a new fuel tank the stalling continued. A test I did was to disconnect both lines at the purge valve and plug them. Car didn't stall but after a couple weeks had fuel coming out of the canister. Reattached the lines to the purge valve and the engine stalled. I made an orifice with a 1/16" hole and put on the intake manifold where the hose connects to reduce the amount of vapor coming in. That did the trick for me. No more stalling.
Is the process the same on a 2001 Sebring 3.0 v-6?
+Deon Carson If it has the same transmission the process should be the same. Hope this helps you out. 1aauto.com
I have a 2.4L 2008 Dodge Avenger. It's stuck in second gear. I got a P0765 code. I installed a new transmission shift solenoid and deleted the code. After a test drive everything seemed fine. Turned on the car again and now I have the check engine light back on and it's doing the same thing again. I heard that the car might have to be reprogrammed to the new shift solenoid by the dealer..is this true?
+Sebastian Lopez Hi I have the same problem can you tell me if you fixed it and what work was done to repair. Thank Jose
U guys ever fix this problem? I too now have this problem.
my chrysler sebring 01 doesnt shift properly recently it jerks, sometimes the car is on drive and the car doesnt move while the engine accelerates. the shifts take way longer to lock in to shifts. whats the problem. would this help?
If the check engine light comes on, you may want to have the code pulled as it may help to point you in a direction as to what the issue is. If the transmission oil hasn't been changed, you may want to have the transmission fluid changed and have a new filter put in. Hope this helps you out. 1aauto.com 866-403-3393
1A Auto Parts hey im getting codes po734, p1782, p1781, po700, po732, Po736, can you give me some help?
hi I have a PT cruiser, would this work for my car awell. is it the same.?
+W&A Goals This part also fits these PT Cruiser years 2001-2010 Chrysler PT Cruiser Transmission Shift Solenoid for Models with A604 4 Speed Automatic Transmission Here is a link to them www.1aauto.com/transmission-shift-solenoid/i/1atrx00005?RUclips&CTA+Comment&CY5uPlDc