This video actually is for Outside mitter. Could you make a video of Inside mitter? I have seen 100s you tube videos, But you are the BEST and only Best.
Waste left side, use Red snips, keeping the handle Above the metal. Means lock opener near thumb side 14. Waste right side, use Green snips, keeping the handle Above the metal.
I made all my "inside" corners following this video, when I got to the job site I was unable to fit them in the "inside" corners of the roof edge. Can you show us how to make outside corners.
Good video, i like the slat cut inbottom back mitre that locks them together. Only thing i wld change is to not have the extra length tab on bottom and no screws on bottom either
Please upload video for inside cornners. By mistake, it is outside corner video but should show inside video. You are the BEST. Title says inside video but it shows outside corner video
A solid method, but as stated it's an outside corner. Also don't think I like the jagged points in there for cleaning out. Also without any sealant during assembly seems like it's clearly going to leak. Looks like I go with the prefab corners for my installation as this looks like more work and tradeoffs than I want to go this route....
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
This video actually is for Outside mitter. Could you make a video of Inside mitter? I have seen 100s you tube videos, But you are the BEST and only Best.
How do you do this corner 30 feet above ground level?
How did you make that template?
Waste left side, use Red snips, keeping the handle Above the metal. Means lock opener near thumb side
14. Waste right side, use Green snips, keeping the handle Above the metal.
I made all my "inside" corners following this video, when I got to the job site I was unable to fit them in the "inside" corners of the roof edge. Can you show us how to make outside corners.
Someone should probably let him know, that was an outside corner.
Good video, i like the slat cut inbottom back mitre that locks them together. Only thing i wld change is to not have the extra length tab on bottom and no screws on bottom either
Around here that would be called an OUTSIDE corner, not an inside corner.
Blue72Red74 I think the title of the video should be learning to make gutters 😌😌😌😎 😛😛😛😛😛😛😁😁
Lol
Absolutely
sir, this is the same video as the outside corner. Can you please upload an inside corner video?
I'm starting a gutter gig tmr and probably only have the job tmr if I did this.
Please upload video for inside cornners. By mistake, it is outside corner video but should show inside video. You are the BEST. Title says inside video but it shows outside corner video
For a start that's an OUTSIDE corner. Did you ever make a mess of that? You dented the hell out of it. Practise makes perfect.
What is the name of the back ground music
Where do u get the template
What is your background music
where to get the template?
I remember when I first learned how to use tools too, I did the same type of stuff.
dat some homely looking corner brah
What type of square tool do you recommended for eaves trough? I noticed different styles and sizes at the hardware store
A solid method, but as stated it's an outside corner. Also don't think I like the jagged points in there for cleaning out. Also without any sealant during assembly seems like it's clearly going to leak. Looks like I go with the prefab corners for my installation as this looks like more work and tradeoffs than I want to go this route....
Absolutely
EXCELLENT!!! ❤️👍🏻👍🏻👍🏻👍🏻👍🏻
Хорошо
If you fold the sheet inside and never cut it you have best result the rivet and the joints never seen outside.
I prefer rivets over screws.Now days we use pre-made cast angles & only need cut the angle no laps required. This is a bit old school. 👍
Lee Bradley The pre made caps look like shit... the externals look seamless done like this
You need relief cuts on the straight edge before you bend the edge around. It’s a lot cleaner look and easier to bend.
I thought this video was for inside corner. LOL
That is an outside corner. Not an inside corner as your video states
Ahhh you dented the outside corner no good throw it out lol.
Rule number one, get a real fucking construction pencil
#chinamarker :p
Очен.хорошо.спасиба
Have to be honest, although I like the principle. It does look a bit rough. Hope it’s being fixed to a sky scrapper
If it was my house you'd be taking that mess off and escorted off the property. What a joke
Great job
no t preocupes del pencil aveces hasta con un clavo
😱
I'm no pro but looks a bit butcherd
Nou nou
Di ko need ng template...kahit wala akong template mas kaya kong gawin ng malinis at di pinupukpok ng gutter...you need more practice bro
Хлопи ти ухїв
good but no nice
No good
Butcher
lol u don't know anything about gutter specially about cutting a mitter system bro