OMG, cannot believe it actually worked. I was just about to give up and start looking for a new wireless mouse because opening up the mouse and cleaning all the lint inside did not fix the problem. Had some plumber's tape on hand and used it as in the video, and now the scroll wheel works. Thanks a lot!
What a life saver! I would give this video ten THOUSAND likes if I could! You just saved me from having to buy a new mouse! What an absolutely ingenious fix! It's like a brand new mouse now, I cannot thank you enough.
Brilliant! I repaired my Microsoft Wireless Mobile Mouse 3500 using PTFE plumber's tape. The center mouse wheel lost its scrolling grip years ago and now it works! I was so close to shopping for a new one! Gotta love YT for these brilliant hacks! Thanks!
Thanks man, it works! In my case, I've used micropore as I didn't have the thread type. The key is, you need to make the shaft thicker to reduce the gap between the shaft and rotating wheel in my opinion.
If every product have a RUclips tip for malfunctions the world wide waste will be reduced by half !! well done !!! In click switches wd40 works perfect but for wheel malfunction your solution was genius.
Thanks because your video encouraged me to try and fix my mouse insted of discard it. In my case, a wireless Genius, the encoder was rolling smooth, nothing seemed to be malfunctioning, so I decided to use a Wahl oil (yes, the electric hair clipper) on it, and it started working again from almost being unusable. Afterwards, I removed the excesss of oil and got back to work :)
Thank you so much for the solution! I've been struggling with the mouse wheel for a while and couldn't find a fix. I guess, at least in my case, the plastic must have worn down over time, which is why it became too thin to make proper contact.
Thank you Sir! The cogwheel not moving was the issue and the critical clue to my fix! Yaaay! I found it easier to layer a small square over the cogwheel hole and push the shaft through rather than trying to attached the tape to the shaft (not much shaft to work with).
The tiny shaft of the wheel is hexagonal shape, and fixs in the hex hole, but with the use, the plastic cornes get round so the tape trick works fine, thanks!
Thank you so much for this video. ive been struggling with my mouse for a while and your humble and to the point video was the answer i needed. thank you so so much
I had a slightly more extreme problem. The shaft of the wheel had snapped where it enters the encoder. I was able to retrieve the tiny nub that was still in the encoder. I then pushed a hot needle down the centre of the nub and into the shaft of the wheel. I then dusted the joint with bicarbonate of soda and put a few drips of superglue onto it. After allowing it to set completely (about 10 minutes) I then cut off the excess needle (that was still sticking out), reassembled and it works.
Thanks for the video. It helped to find the root cause of the issue. Tape didn't work properly. So, I used thread instead and my mouse working perfectly now.
Well, I at first just cleaned it and that worked for that particular mouse as it had some hair + dust all over the scroll wheel. Thank you for taking the time to make this tutorial and let us save some money from buying a new mouse :D hope you have a lovely day! ❤
NAHHH, i found others video fixing their mouse but my mouse just broke cuz their fixing is hard, and this video makes my mouse fix cuz he fix easy. this video is great bro thanks
A high tech version of the Red Green Show using teflon tape instead of duct tape. "So, if the women don't find you handsome, they should at least find you handy."
This is the solution that worked for me. New Hama mouse started having scroll problems after 1 week of heavy use. I guess germans don't make things like they used to...
I got my mouse wheel fixed thanks to this video! I cleaned it first (there were a lot of cat hair in it lol) and tried different tapes but my mouse wheel had different kind of nub at the end so tapes just didn´t work, but I but a little dab of hot glue and let it dry and that did the trick!
Thx.... basically what I did though instead of that because it didn't work as well kept slipping anyway was cut the tape about the size of the hole or a little bigger, basically a square, layed that over top of the hole where the wheel goes in, then attached to push the wheel through it.......works perfect 👌
i have an adorable little "mouse mouse", as i like to call it - my mouse looks like a little hamster! i was having this problem and i was so sad because i totally thought i'd have to replace him :( but once i opened him up for surgery, all i had to do was jostle that little gear a bit and it went right back to scrolling normally! thanks for your help! :)
Thank you for this!. Now, I'm feeling effing dumb for not thinking about that before. I mean, it's clear the scroll wheel was losing friction, duh!. But, I'm just using a little piece of tissue, and it works again!.
Threw it in the bin, after 40 minutes of trying to get the top part of the case back on enough was enough. I'd love to speak to the engineers of some of these products and ask them what they are thinking.
In recently bought a “Logitech M189” wireless mouse to replace my old one as the “scroll wheel” stopped working. Everything on it worked okay, except for when I tried to type text, even in the “Search box “it wouldn’t show. Has this happened to anyone, if so, how did you fix it?
Thanks bro, i am a lefty gamer and i have trouble finding good mice that are somehow symetrical let alone good gaming lefthand mice in a reassonable price range. this video helped me put back in track my favorite mouse which even thou is about 10 years old still outperforms the chinese c**p i can afford these days.
my days of trying to fix my Razer Viper mini leads to cleaning dust from the wheel, to noticing the lack of resistant of the scroll wheel and ended w/ the same treatment. it seems like the wheel shaft being dislodged case the wheel to slip and lose contact why the scroll jumps back and forth. cool!
What if the green mini wheel spins but it still doesn't scroll? Like it only goes sometimes. And usually I kinda fixed it, then I scroll for flawlessly for 5 seconds and then it is busted again. Edit: Okay, I had to fix the green mini wheel casing. Glad I didn't break my mouse and fixed it. Thanks for your video.
I had a different problem with my hp wireless mouse, the whole part which goes inside the scroll wheel sensor thing was broken off somehow.used super glue to stick it back on it its place
Went to try this on an Onn. mouse, but there are no visible screws on the bottom. The feet are plastic, and peeling back the corner damages the plastic, so I'm not sure if there are screws to remove underneath, meaning this fix might not be possible on models like this. Granted, the mouse itself costs about $12 these days, but I'm more annoyed by the disposal requirements of electronics than the costs of a new one.
Hey! im 12 years old and im looking foward if you know a little more info for this. Because when i did the tape method all it did was turn the tape around adn the plastic thing that makes your spin wheel work didnt move. PLEASE HELP 🙏
quick tip guys if this problem doesnt work use another method which is press the circle thing you scroll down with and move your mouse up and down slowly Hope it works actually it should work for all mouses Bye have a great day or night
When you click on the wheel, it should have unrestricted movement up and down. So I suppose, a flexible (silicone-type) glue may work. But not the super glue.
thank you, but there is no like thumb only thumb down.👍So here is my thumbs up. I see that on other peoples sites. Maybe you guys need to report that. your presentation was very good.
This man deserves an award! What a simple and brilliant 5 minute hack that saved me time and money.... Simply outstanding!!!
Glad it helped.
OMG, cannot believe it actually worked. I was just about to give up and start looking for a new wireless mouse because opening up the mouse and cleaning all the lint inside did not fix the problem. Had some plumber's tape on hand and used it as in the video, and now the scroll wheel works. Thanks a lot!
Good to hear it!
Teflon tape worked perfect. Was considering throwing the mouse away but this was super helpful! Thank you!
What a life saver! I would give this video ten THOUSAND likes if I could! You just saved me from having to buy a new mouse! What an absolutely ingenious fix! It's like a brand new mouse now, I cannot thank you enough.
Great to hear!
Excellent. Worked perfectly using Microporous Surgical Tape out of the first aid box. Great to have the scroll wheel back in action.
Good to hear it!
when it started working ahaa moments for user
Brilliant! I repaired my Microsoft Wireless Mobile Mouse 3500 using PTFE plumber's tape. The center mouse wheel lost its scrolling grip years ago and now it works! I was so close to shopping for a new one! Gotta love YT for these brilliant hacks! Thanks!
Thanks for sharing!
Sitting here high af at midnight with that problem. Now i sit here crying from your help. Thanks man!
using tape around the shaft is a great solution.
it worked perfectly. thank you so much.
Glad it helped
Thanks man, it works!
In my case, I've used micropore as I didn't have the thread type. The key is, you need to make the shaft thicker to reduce the gap between the shaft and rotating wheel in my opinion.
If every product have a RUclips tip for malfunctions the world wide waste will be reduced by half !! well done !!! In click switches wd40 works perfect but for wheel malfunction your solution was genius.
Thanks for watching.
thankfully I found that white tape laying around in the house, worked like a charm, thanks a ton
Good to hear it!
Thank you! The final fix worked! Increase the shaft size worked for me! 🥰
Excellent!
Thanks because your video encouraged me to try and fix my mouse insted of discard it. In my case, a wireless Genius, the encoder was rolling smooth, nothing seemed to be malfunctioning, so I decided to use a Wahl oil (yes, the electric hair clipper) on it, and it started working again from almost being unusable. Afterwards, I removed the excesss of oil and got back to work :)
Good to hear it!
ty for your video :P you also help me selffix my 20$ mouse
Really helpful, i couldn't find Wahl oil tho, so I used cooking oil, and it still worked fine. Thanks for the inspiration.
Thank you so much for the solution! I've been struggling with the mouse wheel for a while and couldn't find a fix. I guess, at least in my case, the plastic must have worn down over time, which is why it became too thin to make proper contact.
Great to hear!
Thank you Sir! The cogwheel not moving was the issue and the critical clue to my fix! Yaaay! I found it easier to layer a small square over the cogwheel hole and push the shaft through rather than trying to attached the tape to the shaft (not much shaft to work with).
Thanks for sharing.
The tiny shaft of the wheel is hexagonal shape, and fixs in the hex hole, but with the use, the plastic cornes get round so the tape trick works fine, thanks!
Cool, thanks!
Thank you so much for this video. ive been struggling with my mouse for a while and your humble and to the point video was the answer i needed. thank you so so much
Glad it helped!
I had a slightly more extreme problem. The shaft of the wheel had snapped where it enters the encoder. I was able to retrieve the tiny nub that was still in the encoder. I then pushed a hot needle down the centre of the nub and into the shaft of the wheel. I then dusted the joint with bicarbonate of soda and put a few drips of superglue onto it. After allowing it to set completely (about 10 minutes) I then cut off the excess needle (that was still sticking out), reassembled and it works.
Thanks for sharing.
Please let me know if this worked for you as well. If not, how did you fix it?
Thank you very much. My scroll wheel was acting weird but it's fixed thanks to your video.
It’s worked Dude Thanks Alot for helping Me
Thank you so much! It worked perfectly with the Teflon tape on a wireless mouse (Hama AM-7300) 😊
Glad it helped!
Thank you! The tape trick worked and I would have never figured what was the problem if not for this video :)
Glad it helped!
Thanks for the video. It helped to find the root cause of the issue. Tape didn't work properly. So, I used thread instead and my mouse working perfectly now.
Thanks for sharing
Well, I at first just cleaned it and that worked for that particular mouse as it had some hair + dust all over the scroll wheel. Thank you for taking the time to make this tutorial and let us save some money from buying a new mouse :D hope you have a lovely day! ❤
Thanks for watching!
Fixed my mouse wheel perfectly with the plumber tape which I had at hand. Thanks!🎉
Good to hear!
genuine life saver, i cant thank you enough
NAHHH, i found others video fixing their mouse but my mouse just broke cuz their fixing is hard, and this video makes my mouse fix cuz he fix easy. this video is great bro thanks
Thank you so Much , Your video helped me a lot and saved me from buying another mouse
Great to hear!
bro you really helped me fix my wireless mouse.
Good to hear it!
I'm glad I found your video! THANK YOU SO MUCH, SIR! ❤❤❤
Happy to help!
A high tech version of the Red Green Show using teflon tape instead of duct tape. "So, if the women don't find you handsome, they should at least find you handy."
That tape idea worked in first try I was about to throw my mouse but now it's working fine .. thankss
Great to hear!
The tape trick actually worked! Thank you! 👍
Great to hear!
It fixed my wireless mouse....using a Teflon tape...Thank you...
Excellent!
This is the solution that worked for me. New Hama mouse started having scroll problems after 1 week of heavy use. I guess germans don't make things like they used to...
Thank you so much. I was able to fix my mouse scroller with ease.
Great to hear!
I got my mouse wheel fixed thanks to this video! I cleaned it first (there were a lot of cat hair in it lol) and tried different tapes but my mouse wheel had different kind of nub at the end so tapes just didn´t work, but I but a little dab of hot glue and let it dry and that did the trick!
I was thinking of trying the hot glue myself )))
Thanks for sharing!
Thanks man.....your video still is a life saviour!🤗
Glad to hear it!
Thx.... basically what I did though instead of that because it didn't work as well kept slipping anyway was cut the tape about the size of the hole or a little bigger, basically a square, layed that over top of the hole where the wheel goes in, then attached to push the wheel through it.......works perfect 👌
Thanks for sharing!
great idea. wish I would have read this before I fixed mine.
Your technique was perfect. Thank you.
So glad!
Worked for me too! Was going to throw this favourite mouse (Rapoo) but it now has a new lease of life...
Good to hear it!
Perfect! Thanks for the video, and for probably a few more years life for my HP mouse!
Great to hear!
I was literally going to throw it. Thanks man! 👍
No problem 👍
Turns out mine didn't even need the tape, it just needed 5 years' worth of dust and hair removed🤣
The plumbers tape worked like a charm!!!!
Good to hear it!
Omggg that seriously works , thank you so much .Love from India
Good to hear it!
Great fix. I added scotch tape on mine and it worked
Good to know!
Amazing...! Thanks. That little white tape trick really works for me...
Great to hear!
Thanks man, you saved me $20 bucks on a new mouse!
Good to hear!
It works for me. Also using plumber's tape. Thank you!
Excellent!
Thanks for the idea! I used masking tape and it works like a charm :)
Good to hear it!
How do you take of and put back the rubber feet ?
Not sure. The feet could be glued or just inserted.
You could try a small screwdriver to prime them off.
Thanks a lot, the plumbers tape helped😊
Great to hear!
tried it with some paper tape and it worked! thank you!
Awesome!
i have an adorable little "mouse mouse", as i like to call it - my mouse looks like a little hamster! i was having this problem and i was so sad because i totally thought i'd have to replace him :( but once i opened him up for surgery, all i had to do was jostle that little gear a bit and it went right back to scrolling normally! thanks for your help! :)
Good to hear it!
Thanks so much! Looks scary but it was actually pretty easy. I used elastic electrical tape and it worked great it seems
That's great!
@Your-Self Damn that is an impressively quick response lol
Thank you for this!. Now, I'm feeling effing dumb for not thinking about that before. I mean, it's clear the scroll wheel was losing friction, duh!.
But, I'm just using a little piece of tissue, and it works again!.
Thanks for sharing!
The only way that worked for me, thanks a bunch ❤❤
Glad to hear that
thanks i was trying to figure this out for a long time
Glad I could help
Still working bruh with my logi g703 because of you. Thx you sir!!!!
Awesome!
Threw it in the bin, after 40 minutes of trying to get the top part of the case back on enough was enough. I'd love to speak to the engineers of some of these products and ask them what they are thinking.
Thanks I was able to fix it after watching your video
Just WONDERFUL! Thank you so much, Man!
Enjoy!
Simple and effective tutorial, will try on my non functional scrolling mouse.
Good luck!
My wireless mouse was peed on my cat 😢then i tried to fix it with this video and it worked a bit thanks
Thank you for sharing this video. I fixed my wireless logitech mouse(M275) the same way. :)
Good to hear it!
thank you, very simple and it works!
Great to hear!
In recently bought a “Logitech M189” wireless mouse to replace my old one as the “scroll wheel” stopped working. Everything on it worked okay, except for when I tried to type text, even in the “Search box “it wouldn’t show. Has this happened to anyone, if so, how did you fix it?
Thanks bro, i am a lefty gamer and i have trouble finding good mice that are somehow symetrical let alone good gaming lefthand mice in a reassonable price range.
this video helped me put back in track my favorite mouse which even thou is about 10 years old still outperforms the chinese c**p i can afford these days.
Good to hear it!
Thank you, it such a pain when come to scroll button mouse broken 😮💨
omg!! Thank you so much dude!!! It perfectly works with the Teflon tape on my Genius NX-7000 T__T thank you so much!!!
Good to hear it!
my days of trying to fix my Razer Viper mini leads to cleaning dust from the wheel, to noticing the lack of resistant of the scroll wheel and ended w/ the same treatment. it seems like the wheel shaft being dislodged case the wheel to slip and lose contact why the scroll jumps back and forth. cool!
What if the green mini wheel spins but it still doesn't scroll? Like it only goes sometimes. And usually I kinda fixed it, then I scroll for flawlessly for 5 seconds and then it is busted again.
Edit: Okay, I had to fix the green mini wheel casing. Glad I didn't break my mouse and fixed it. Thanks for your video.
My wife thinks I'm such a beast now.
LOL, you're welcome :)
in my case the mouse wheel rotates backwards from its direction and because of that the wheel doesn't work properly, can this method also fix it ?
yeah if it jumps try it, sometimes 8 out of 10 the mouse wheel shaft gets dislodged or its material wears and the surface lose contact , so tape works
I had a different problem with my hp wireless mouse, the whole part which goes inside the scroll wheel sensor thing was broken off somehow.used super glue to stick it back on it its place
Thank you!!! It worked for my HP wireless mouse!😃😃
Good to hear it!
Went to try this on an Onn. mouse, but there are no visible screws on the bottom. The feet are plastic, and peeling back the corner damages the plastic, so I'm not sure if there are screws to remove underneath, meaning this fix might not be possible on models like this. Granted, the mouse itself costs about $12 these days, but I'm more annoyed by the disposal requirements of electronics than the costs of a new one.
Worked for me! Mine was skipping randomly. Fixed my double click issue as well.
Hey it worked!! Thanks a lot for the video❤
Good to hear it.
Hey! im 12 years old and im looking foward if you know a little more info for this. Because when i did the tape method all it did was turn the tape around adn the plastic thing that makes your spin wheel work didnt move. PLEASE HELP 🙏
Thanks bro, It scrolls like new now.
Great to hear it!
i spilt wateer on my razer deathadder v2 pro and now the scroll wheel doesnt work at all. is there a way to fix that?
quick tip guys if this problem doesnt work use another method which is press the circle thing you scroll down with and move your mouse up and down slowly Hope it works actually it should work for all mouses Bye have a great day or night
helped alot, but my problem was the the part that went into the thingy broke off
oh god it worked! thank you so much!
Glad it helped!
thanks a lot now my mouse is working
Good to hear!
woah tBeside from the fact I need to put tape is that the small metal is crooked that is why it is not moving,but thank you so much mate!!!
thank you it work on me. i think i can use glue but it works when i used double sided tape.
Great!
Thanks bro, it worked perfectly
Good to hear!
Thank you for this great demonstration!
Glad it was helpful!
Great video man
You will be now known as the grand mouse saver🤣
Why not just super glue the wheel to the rotary encoder eliminating the chance of slip?
When you click on the wheel, it should have unrestricted movement up and down. So I suppose, a flexible (silicone-type) glue may work. But not the super glue.
@@Your-Self micro switch is normally the other side and just a tilt movement, the axle mounts allowing for this.
How can you fix a expensive one
thank you, but there is no like thumb only thumb down.👍So here is my thumbs up. I
see that on other peoples sites. Maybe you guys need to report that. your presentation
was very good.
Thanks for the info
thank you! Worked perfectly!
Glad it helped!
May god bless you you a true life saver
I just got on my computer the play games and I couldn’t really scroll I checked a few videos but I think this was the one that works
i dont have the screw at the bottom and its not a cheap mouse i need another way to fix it
I have the same problem with a hp x220 gaming mouse can you tell me how to fix it? Edit: this might work with it just I might break it