Thanks for the great video Mike. Lots of great info. I have just gotten a couple of silly prices in the UK for a 1kw machine. Way over £100k. So good to know there are cheaper options that can work probably just as fine. I hope your machine will last for a long time.
Thanks, Ric08. I’d guess for that kind of money, you get great training, support and the laser might have more parameters. For the huge price difference, I’m prepared to learn by experiment and rely on support via internet. So far, so good.
Thanks for the video Mike. I’ve been looking at buying one of these for a while but the local suppliers are talking 140-180k and I’ve been hesitant to get one from China because the price difference is so huge it’s hard to imagine I would get a half decent machine but after watching your video I’m confident a machine like yours will do what I want to. Thanks again 👍
Thanks, Ramon. I’m sure the big dollar machines are excellent in every way with local support and training. Going the China route gets you started in a profitable line of work that could lead to bigger things. Good luck with your enterprise. Cheers.
Aussie Mike where are U located? Been thinking of purchasing a machine to remove rust in roof of a 4x4. Approx 4 m long X 100mm wide. Then I could bog and paint small holes and weld in patches on bigger ones. Would a 300watt do the job. Also would use to clean aluminium outdoor table and chairs that have several layers of paint. Thanks in advance for your reply. Regards Colin
Thanks for watching, Colin. You don’t want high power in sheet metal like yours, so yes 300w would do the job. Ideally, a pulsed laser is way better than continuous wave. You could have even lower power too, maybe even 100w. Pulsed machines are more expensive, but easily portable and low power consumption. If I had my time again, I would get a 200w pulsed laser. Mike
Let me add a little info. This thing is a continuous wave 1064nm laser. It will absolutely fuck you up. It adds immense amounts of heat to everything it touches including the substrate. It will melt steel. It will not however remove rust as such. It changes the surface of the rust leaving the impression that it removes rust, but unless we're talking very superficial rust there's gonna be rust underneath. If you want to remove rust you need a pulsed laser. A pulsed laser won't burn and is inherently more safe than this diabolical thing. But a pulsed laser is expensive. Don't focus on wattage btw. It doesn't mean much of anything.
Thanks for commenting, Whiskey Throttle. I agree, these things are potentially very dangerous. Just like… well everything in a workshop. Safe operation is down to the operator. Yes, pulsed lasers are much better. They remove contaminants more efficiently, less likely to damage the substrate, have lower power requirements and are smaller than CW lasers. Yes, the CW adds immense heat and can melt metal. I can’t say I agree that it doesn’t remove rust though. Sure, it doesn’t work as good as pulsed, but I definitely see rust removal. CW takes a lot of time and experimentation to get the right scanning pattern, width, speed, power and technique to remove contaminants,including rust with minimal damage to the substrate. It also takes longer than pulsed. Everything about pulsed is better than CW. Except the cost. If I had my time again I would’ve waited and chosen pulsed. If I were buying one of these to make a living I’d buy a pulsed. Why would anyone buy a CW? It’s way less capital outlay, great to learn on and gets a foot in the door of laser cleaning. Put the time in to get good at CW, you can make enough to finance the upgrade to pulsed. Or if it turns out that laser cleaning isn’t for you after all, then the loss isn’t as high.
Hi Mike, nice video thanks, How close can you get to the work surface? say removing rust from a car frame? Working under the car on all the different surfaces? Thanks.
Thanks, Gregory. Good question. Lasers have a fixed focal length determined by the lens. Maximum power on the surface is when the laser is held at that distance from the surface. It is possible to move closer to (or further from) the surface, but the power drops off. Mine is 400mm. You may be able to select a shorter focal length lens, but you don’t want the lens too close to the surface because the fumes may contaminate the lens reducing efficiency and shortening life. For working under a car, I’d have it on a hoist.
I have had corresponding emails with companies with the lasers and they are very conflicting. Some show the laser gone right over the guys hand without hurting it a bit and then you show this video of this laser actually vaporizing bees and burning wood. They say it doesn’t affect the substrate of whatever you’re working on and that is false . Thanks for the video
This is because people use different types of lasers. The ones used for corrosion and soot removal are expensive 100-300 watt pulsed lasers at 1064 nm. This one is a continuous wave laser, still at 1064, and will absolutely burn everything to shit. I've held my hand in a pulsed laser at 300w, but fuck me if I'd do it with a continuous wave laser. The CW will melt steel and the beam reaches hundreds of meters because they have no optics. The pulsed lasers have a very limited focal point and won't burn. But it will mess up your eyes though.
@@whiskeythrottle9369 I have a continuous laser, and you do have to be aware of how high your power is on certain things. It is the 1064. I do wear the safety glasses designed for it. As far as crossing my hand, no thanks, but this one does have a focal point, you can hear the difference in it when in use. If you get too close or too far away while using it, it’ll let you know. Just gotta have a bit of common sense. youtube.com/@Laserguy660
Thanks for watching. For the cleaner, only a small compressor is needed. It's only function is to stop residues contaminating the lens. As long as there's an airflow over the lens, the vaporised material can't touch it. If you get a laser welder, you'll need more specialised equipment. I only have a cleaner, so I've not looked into the welding side.
Good question, Eric. This is such a new option with the advantage of no mess. You still need to be competitive in your area, though. Look around to the pricing of sandblasting companies for paint and rust removal, graffiti removal, mould cleaning etc. Then charge more than that. Sell the fact you aren’t using chemicals or water or beads and there’s no mess. You’ll need to get those settings nailed, but that comes with practice and documenting. While you’re the only one in the area doing it, charge a premium while you can.
Hey Mike, thanks for the great video. I am expecting my machine from ACCTEC in the next few weeks and I was hoping you could give me some guidance with regard to stripping paint from wood. With a 1500 watt machine, what setting (power wise) should I be shooting for ? I don't want to burn down the building. Thanks in advance.
Hey Paul, good question. I haven't tested paint from wood removal yet. One of the things in the long list. You'll be aiming for low power and one of the patterns that prevent the laser staying on one spot too long. Getting the right settings is trial and error and loads of practice. It takes practice to get a feel for how high off the material to keep the laser and how fast or slow you move. Paint some scrap wood now, so when your machine arrives you can start experimenting and take notes of everything you test.
Good question, Robert. Laser works very well with paint on bricks. They’re used to remove graffiti on any surface. With the right settings, there is no damage to the underlying material. Laser also removes the soot from bricks and tiles after a house fire.
Hi again, would really like to know what its like on older car panels to remove paint and rust etc? Really concerned of the thin metal on panels getting to hot and warping. A heat gun reading would be good if possible? Keen on getting one to help restore my cars. How has the machine been operating for you? What sort of water are you using? Thanks again, it was a great video.
Hey Brenda, I can’t offer personal experience with old car panels. Maybe I can find some old rusty panels at the wreckers to experiment on and do a video. It’ll be a while though. I’m flat out at the moment. I use distilled water in the chiller. It’s a terrific machine, though I don’t use it enough.
Lasers of this type will absolutely warp car panels. You need a pulsed laser for that type of work and then you still need to be careful. And consider a laser a delicate brush. It will "paint" but very inefficiently so over large areas.
hey Mike thx .. I'm in the EU where there's a lot of stone buildings with discoloration due to types of lichen .. and I was wondering if you think this type of machine could clean this stone ? I know they're very expensive but this is just an idea ... thx
Yes, definitely the right tool for the job. I’d go with a 100W or 200W pulsed laser. It’s much smaller with lower power requirements than continuous wave like mine. For remote jobs you want an easy machine to move. The pulsed lasers are more expensive, but the technology means you get a lot more bang for your buck.
hello, sir, this is Gloria from ACCTEK company. Mike's sales, the laser cleaner machine clean the stone, and buildings is okkk:) and the machine price now is very effective, may i know your email address? then we can talk further, thanks in advance.
Thanks, Hank. It’s been so wet, I haven’t been able to do anything with the bees. Still waiting for an opportunity to transfer a colony into the long Lang.
Hey Pascal, thanks for watching. You’re best to contact AccTek for details. There are different models with a range of specifications to choose from. Mine was about US$7K plus shipping. They’ll arrange freight to your nearest port, then you deal with customs and last leg freight through a customs broker. It’s not difficult and way cheaper than buying a European or US machine.
Hi Mike how is the machine going . Im considering grabbing one for commercial use. Do you think it would hack day to day use. Did you look at other chinese companies. Any advice would be greatly appreciated Mike. Thank you
Hey Nik, My laser is going good, but I’m only an part time user. I have every confidence that it can handle full time duty. It’s a very solidly built machine. My experience with Acctek has been positive. They’ve responded to my requests for help whenever I’ve asked. If I had my time again I would choose a 200watt pulsed laser. Much lower power requirements, portable and more effective than the continuous wave. I did look at other manufacturers and found they were a little deceptive about pricing. Acctek were straight with every detail: the deposit to start the build, final payment before shipping and the shipping cost and details. The only extra cost is local import fees, customs and transport from port to my place. Mike
@@AussieMikesBees thanks for your reply mate. Yeah was considering the 200 pulsed laser but it does cost a few K more but my biggest worry is would it have the punch for heavier rust etc. I was going to throw the 1000 in a van with appropriate gennie. But I can see the downside with gennie costs and moving the thing around. Acctec are using your video in there promotion material. Just a heads up in case you are unawares Cheers
Hey Nikky, The thing with pulsed is they pack a punch above their weight class. Each pulse is higher power for short duration. I haven’t used one yet, but all I’ve heard indicates it’s more than capable of rust removal with lower risk of damage to the base metal. I think you would forget the extra outlay, when you have much lower power requirements and weight. Get a good fume extractor fo mobile jobs.
hello mike just got my machine but the peaple at acctek dont give full infermation on full set up your video and replys are very helpful what size commpresor do you use and will the laser work with out the compressor attached. you give more infermation than acctek good job and also is the commpressor just for keeping contamanets away from lens or dose it have other perpase
Hey Jake. The downside of buying Chinese at low prices is there is no training. The best teacher is experience and doing loads of trial and error taking notes on settings that work. I know people can fine tune these machines really well. I don't use mine everyday, so I've been surpassed by others that bought their's after me and you will too if you're making a living with it. Yes, the compressor is to keep the lens clear of contaminants. I wouldn't run mine without it. You don't need anything special, just capable of the run-time you'll be requiring. Mine is a better than handyman, less than pro model that I use for my CNC router and CNC plasma and general use around the shop. I recommend a drier of some sort.
Hi Mike, great video and it's so refreshing to see real world workings of this type of machine unlike most other videos on RUclips showcasing laser cleaners. I'm going purchasing one of these machines and found supply companies in China interesting to deal with on a technical level. Wondering what your experience was with AccTech as these machines are a lot of money, have you had to chase after sales assistance and what is the quality like etc...
Thanks for commenting, Trent. I’m pretty happy with AccTech so far. They seem keen to keep me happy. Not that I’ve needed tech help so far. The machine works flawlessly. Gloria from sales touches base with me periodically. Not to sell me anything, just checking that I’m happy with the laser. I would definitely buy from them again. I have no affiliation with them. I don’t make any money on referrals or any other way with them. It’s my opinion based on my experience. I’ll be shooting a video of cleaning my very dirty stainless steel bbq (grill for the Americans). I think it will work very well. It’s one of those jobs I detest.
Thanks, Ollie the Collie. Yes, I’m happy with the machine. If I had my time again, I would go with a lower power pulsed laser. They are easier to work, smaller and lower power requirements. Down side - higher cost.
@Ollie the Collie I haven't used one yet, but from what I now understand of the technology, pulsed can be dialed in with precision to get amazing results on a wide range of materials. CW is sort of a sledge hammer - you can hit the pin nail gently, but it takes more effort to get it right than using a pin nail hammer. CW can put a lot of heat into the substrate if you're not careful and that could damage the part.
Like, if you could remove the paint and keep the laser moving around and limit, or not burn the wood of the pencil. Im wondering how this would do on furniture if your careful.
Hi, have you used this machine on heavily rusted car panels, body or chassis? Also painted car panels? Thinking of buying a 1500 w machine. Appreciate any feedback? What state are you in? Thanks, Lee.
Hey Brenda, thanks for watching. Yes, the laser burns through thick paint and rust. It’s worth scraping loose material off first, so you’re only lasering bonded paint and rust. More power means more choices. You can turn down the power for thinner materials. Too much power can overheat and warp thin metal. It’s a bit of an art.
Hi Mike, Is there any chance you could reply with link of where you bought this from? I’m in Tassie and looking to buy one cheap enough to learn with before spending heaps on an expensive one. Also, can you give details on the power pack your using, Cheers, Paul
G'day Paul. I bought mine from Acctek through Alibaba www.acctekgroup.com/Laser_cleaning_machine/Fiber_laser_cleaning_machine_for_metal_1000W_5156.html Not sure what you mean by power pack. I use a 32A outlet that I share with my CNC plasma (running one machine at a time). Although the laser has a 32A circuit breaker, I believe it might be possible to run it on a 20A outlet.
Hi Mike cool video. I'm from Brisbane and am considering this as a business. I have a couple of questions hopefully you can help me with. Would not your 1000 model also fit into a van? How long is the cable Lead ? I see Acctec are using a part of this video to promote there products are you aware of that. What made you choose this company , I'm also considering DMK. Any advice greatly appreciated. Cheers
I'm sure it's gonna be hard to get an answer as you look to be a very busy man. I'm VERY interested in this company just worried about shipping, was everything shipped at a decent time?
I had no problem importing this laser to Australia. Acctek arranged the shipping to Sydney, then I was contacted by an import agent who organised customs. I paid them the fees and taxes, then picked up from the port. They would have arranged trucking from port to me too, but it was easier for me to pick up. You pay a deposit to start the order, then when the laser is ready to ship, they invoice the final payment. I did it all through Alibaba.
Hey Anton, my Acctek laser uses a Raycus C1000RFL source which is a continuous wave CW. Check out the details here www.acctekgroup.com/Laser_cleaning_machine/Fiber_laser_cleaning_machine_for_metal_1000W_5156.html I bought mine through Alibaba and it was a smooth process. They are under $10K plus shipping and import fees. European and US machines cost five to nine time more.
Thanks for watching. Good question. So far I have not done those surfaces, but I think that would be a good video. I’ll track down some test pieces and work it out. Cheers.
Hey Mike could you possibly paint a brick or a sandstone/ riverstone with masonry paint?? Give it a few coats let it really harden up. And try cleaning it off with the laser . I'd really love to see the prosses and the results. Cheers j the stonemason
Sounds like a plan, James. I’ll get a can of paint and put a few coats on some bricks and rocks. Might be a while before I get to shoot the video, kinda busy right now. Cheers, Mike
It’s been a solid machine, although I had a minor glitch a while back. Turned out to be an interlock problem, nothing serious. If I had my time again I would get a pulsed laser. Smaller unit, lower power requirements, better performance. I don’t remember what mine cost, but it was way cheaper than the European or US brands. You can check current prices at Acctek on Alibaba.
Good question. I don’t have any powder coating experience, so can’t offer a definitive answer. I know paint adheres very well, so I think powder coating would as well. The surface left after rust removal has a fine texture that I think help surface finishes bind better.
Hello Mike, You haven't got a video setting the laser up from scratch have you. Meaning from when you first plug the machine into the power plug then setting all of the perimeters right through to where you are ready to push the trigger. Enjoy all of your videos.
Hey Merv, thanks for the question. I haven’t done such a video, great idea. I’ll sharpen my pencil and put something together. The only videos I see tend to be Chinese factory demos and worksite videos with no commentary. That’s why it takes a while to learn how to operate.
Thanks for the video Mike! I actually ended up buying one of these recently and am about to get started with it... i had some quick questions for you though if you don't mind. What is the jumper cable for? Is it simply attached to the gun to ground it? And did your machine come it or did you fashion it up yourself? Thanks!
Thanks for watching, Mike. My laser came with the cable clamp attached. I couldn’t find a reference to it so I just leave it on the gun. It might be related to welding, though mine doesn’t weld. I don’t see a reason to earth the workpiece. I’ll ask next time a talk to tech support. Cheers, Mike
Thanks, Matt. I bought mine from Acctek through Alibaba. It can be a little confusing when checking prices. Some only show the deposit amount, but it looks like the full amount. You should find a suitable model within your budget. Ensure you know the shipping and import costs too. I engaged an import agent to arrange for the import fees and local transport costs. The factory arranges the shipping from them to your nearest port and the documentation needed for importation. Pass these to your agent, pay the fees and the rest should be easy. If I had my time again, I’d consider pulsed laser and combination cleaner welder.
@@AussieMikesBees thank you for the detailed reply I really appreciate it! Never bought from Alibaba before but since you did and seem happy I think I would give it a whirl. Also I will look into the 3 in 1 combo that would be splendid, thank you sir!
I’ve bought several different items from Alibaba with no problems. Ask plenty of questions. They’re very responsive. There isn’t really anything on the training side, though. You’ll have to put the time in to experiment with the settings to get the best results for each material and coating. Create your own chart and keep adding to it with each new job. Maybe one day there’ll be a user group where we can exchange ideas.
@@EasyFLtutorials Alibaba. AliExpress isn’t really set up for bulky, heavy items. I’ve bought many smaller items from AliExpress that use airfreight. Machines like the laser, honey pump and CNC plasma were sea freight and Alibaba seems to handle it better. You deal with the manufacturer instead of a reseller.
Thanks for the feedback. What do you use yours for? Have you worked out the best settings for material you work on, or still fine tuning? Has it proved to be better than alternative methods. Have you had any problems with it? If so, what was your experience with tech support to fix it?
Hey Mike, placing my order next month for your exact model. How has your machine held up over the year? any lenses burned out and are replacement lenses obtainable? I am beyond excited to join the laser cleaning game!
Hey Charles, congratulations on your machine. Mine came with a bunch of spare lenses and I still haven’t needed to change the first one. I’m not a heavy user though. Your experience could be different. Depending on your application, I’d consider going for pulsed laser in the 200W range. They perform very well and are portable with much lower input power requirements.
Good question, Lee. It’s possible to put a lot of heat into the metal causing it to warp. The idea is to use the lowest power that vapourises the material being removed. It’s also necessary to keep moving the laser around the material to minimise heating one spot too much.
Depends on your application. CW is like a sledge hammer. You can blast alot of deep rust using loads of power. It'll eat into the substrate too. It is possible to more gentle surface cleaning, but it doesn't have the fine tuning available in pulsed. Also pulsed machine can be much smaller for a similar effect. If you're going onsite to clean moulds or soot off bricks, remove paint from sheet metal then I'd go for pulsed. If you'll have a workshop where people bring their stuff to you for rust removal, maybe CW will do. I'm sure the manufacturers will steer you in the right direction. Enjoy the trip.
Thank you for the advices and explications! ill try to find the good one at a good price. If you pass by Tokyo someday let me know, i hope my laser cleaning company will be already on the good way
I have one but the head overheats and the chinese are awful to deal with. They never answer any questions. Do you use compressed air when cleaning? If so what pressure
Thanks for sharing your experience. It’s a gamble buying anything from China. I’ve been mostly lucky especially with my lasers. I have no trouble communicating with AccTek for tech support. So far I haven’t needed parts, so have no comment about that. What brand is yours? I use about 90-100psi compressed air to prevent the lens being contaminated by smoke. My head has is cooled by the chiller. If the lines were kinked, it might cause overheating.
Thanks for watching. I bought before everything exploded with Covid. For current pricing check with Acctek through Alibaba. You’ll need to factor in customs, taxes and internal transport above the shipping that Acctek arrange. It will still be massively cheaper than US or European brands.
Thanks for watching, Stephan. I bought mine from AccTek through Alibaba. They’re a pretty solid Chinese company and a fraction of the price of a European or USA machine. The flip side is no local training or support. If things go wrong you talk or email with the factory and get parts sent to you. I haven’t needed that yet, but Gloria from sales keeps in touch to see how things are going. Check current prices online. Watch it though, some companies advertise a really low price without saying it’s only the deposit. AccTek takes a deposit to start the order and the balance before shipment. They’ll tell you the full cost and shipping. You’ll need to sort import costs on your end.
@@FHGWoodworking I think it might have been around AU$12K. I picked it up from the docks, so factor in domestic shipping. They supply a bunch of spare lenses. As long you keep the airflow, the lens doesn’t get contaminated. I’m still on my first one, but I don’t use mine full time. It’s a secondary tool for me.
Thanks for watching, Christian. It uses compressed air to stop the vaporised particles contaminating the lens. I believe the welding version uses different gasses to match the metal.
@@AussieMikesBees Hello howare you Sir, sorry to bother you again. Which oil and water separation and filtering system do you use with your compressor to work with the laser machine? Thank you.
I don’t use anything fancy, Christian . It’s not as fussy as a plasma cutter. Just a simple cartridge filter is fine. Obviously, if you already have refrigerated drier filter you might as well use it.
@@AussieMikesBees Thank you very much for your answer Sir. I recently bought a machine similar to yours 1500w. The Chinese sales representative told me that I need a drying and oil removal separator system for cleaning, for cutting and welding needs nitrogen. I'll be sharing the results with you later. Thank you for your help. Best regards.
I've seen videos of laser cleaning on smoke damaged walls of a house. The laser machine was in the truck, power connected to the house, and a long hose with the handheld nozzle doing an effective job at a great distance. So this is 'portable' too.
I want one of these. I’d be spraying metal stuff in my garage with salt water….just so I could blast it. I’d also keep in it the back workshop area which I call “The laboratory “ where my wife is not allowed unless she accompanied by my dog, who I call my lab assistant, “J-Gore”….
Thanks for watching. I bought mine through Alibaba from Acctek. There are quite a few manufacturers and can be difficult to know which to trust. My experience with Acctek has been good. They’ve been around for a decent time and have a broad range of CNC equipment too.
Chaps & chapesses, you really need to consider fume extraction & filtering. Some of the small dirt particles raised by these machines can be quite nasty, you wouldn't want them in your lungs!
Yes, agreed. I use a powered mask and blower. If I were in a populated area a fume extractor is essential. Any good welding shop extractor would do nicely.
Very true! It takes a woman to point that out. Thanks to us, most men are still alive today. So I find it very funny when they get all macho about their male skills and domains.
I bought mine over a year ago and prices and shipping have changed. Look on Alibaba for current costs. Some vendors only list the deposit, so look out for full price. Way cheaper than European and USA machines.
@@AussieMikesBees Wire brushing and grinding the rust off my tractor wheels today for paint...kept thinking about that thing all day today. I'll put my wheels up on a big hill, point that thing at the U.S. and blast off the rust for me?
While it’s true there is no local support for me, they have been very helpful online. Of course, you can pay three or four times more for a European machine with local training and service, but that puts it out of my budget.
Yes, I watch some RUclips creators with insanely expensive equipment. I dream to have it, but I don’t have the time and often the skill to use it. Happy to be inspired by them sharing.
Thanks for that, Mike
It was more about doing the wrong thing as it is a powerful laser machine, so start up the correct way is a must
Thanks for the great video Mike. Lots of great info. I have just gotten a couple of silly prices in the UK for a 1kw machine. Way over £100k.
So good to know there are cheaper options that can work probably just as fine. I hope your machine will last for a long time.
Thanks, Ric08. I’d guess for that kind of money, you get great training, support and the laser might have more parameters. For the huge price difference, I’m prepared to learn by experiment and rely on support via internet. So far, so good.
Thanks for the video Mike. I’ve been looking at buying one of these for a while but the local suppliers are talking 140-180k and I’ve been hesitant to get one from China because the price difference is so huge it’s hard to imagine I would get a half decent machine but after watching your video I’m confident a machine like yours will do what I want to. Thanks again 👍
Thanks, Ramon. I’m sure the big dollar machines are excellent in every way with local support and training. Going the China route gets you started in a profitable line of work that could lead to bigger things. Good luck with your enterprise. Cheers.
Don't worry buying in China, I have my laser cnc cutter for over a year. Works fine
Aussie Mike where are U located?
Been thinking of purchasing a machine to remove rust in roof of a 4x4. Approx 4 m long X 100mm wide. Then I could bog and paint small holes and weld in patches on bigger ones. Would a 300watt do the job.
Also would use to clean aluminium outdoor table and chairs that have several layers of paint.
Thanks in advance for your reply.
Regards
Colin
Thanks for watching, Colin. You don’t want high power in sheet metal like yours, so yes 300w would do the job. Ideally, a pulsed laser is way better than continuous wave. You could have even lower power too, maybe even 100w. Pulsed machines are more expensive, but easily portable and low power consumption. If I had my time again, I would get a 200w pulsed laser.
Mike
Let me add a little info.
This thing is a continuous wave 1064nm laser. It will absolutely fuck you up. It adds immense amounts of heat to everything it touches including the substrate. It will melt steel. It will not however remove rust as such. It changes the surface of the rust leaving the impression that it removes rust, but unless we're talking very superficial rust there's gonna be rust underneath.
If you want to remove rust you need a pulsed laser. A pulsed laser won't burn and is inherently more safe than this diabolical thing.
But a pulsed laser is expensive.
Don't focus on wattage btw. It doesn't mean much of anything.
Thanks for commenting, Whiskey Throttle.
I agree, these things are potentially very dangerous. Just like… well everything in a workshop. Safe operation is down to the operator.
Yes, pulsed lasers are much better. They remove contaminants more efficiently, less likely to damage the substrate, have lower power requirements and are smaller than CW lasers.
Yes, the CW adds immense heat and can melt metal.
I can’t say I agree that it doesn’t remove rust though. Sure, it doesn’t work as good as pulsed, but I definitely see rust removal.
CW takes a lot of time and experimentation to get the right scanning pattern, width, speed, power and technique to remove contaminants,including rust with minimal damage to the substrate. It also takes longer than pulsed.
Everything about pulsed is better than CW. Except the cost. If I had my time again I would’ve waited and chosen pulsed. If I were buying one of these to make a living I’d buy a pulsed.
Why would anyone buy a CW? It’s way less capital outlay, great to learn on and gets a foot in the door of laser cleaning. Put the time in to get good at CW, you can make enough to finance the upgrade to pulsed. Or if it turns out that laser cleaning isn’t for you after all, then the loss isn’t as high.
@@AussieMikesBees Thank you for the detailed explanation! I thought that CW was pricier than pulsed.
Hi Mike,
Al from the uk. Is the laser still going strong ?.
Thanks, Alan. Yes, it’s rock solid. I don’t use it every day, but it’s never lets me down. I have no problem recommending Acctek.
Hi Mike, nice video thanks, How close can you get to the work surface? say removing rust from a car frame? Working under the car on all the different surfaces? Thanks.
Thanks, Gregory. Good question. Lasers have a fixed focal length determined by the lens. Maximum power on the surface is when the laser is held at that distance from the surface. It is possible to move closer to (or further from) the surface, but the power drops off. Mine is 400mm. You may be able to select a shorter focal length lens, but you don’t want the lens too close to the surface because the fumes may contaminate the lens reducing efficiency and shortening life. For working under a car, I’d have it on a hoist.
I have had corresponding emails with companies with the lasers and they are very conflicting. Some show the laser gone right over the guys hand without hurting it a bit and then you show this video of this laser actually vaporizing bees and burning wood. They say it doesn’t affect the substrate of whatever you’re working on and that is false . Thanks for the video
Thanks for watching, Grizz. I've seen video of a guy lasering his tattoo. He has a bigger set than me. No way I'm getting in front of that beam.
@@AussieMikesBees 😆
This is because people use different types of lasers. The ones used for corrosion and soot removal are expensive 100-300 watt pulsed lasers at 1064 nm. This one is a continuous wave laser, still at 1064, and will absolutely burn everything to shit.
I've held my hand in a pulsed laser at 300w, but fuck me if I'd do it with a continuous wave laser. The CW will melt steel and the beam reaches hundreds of meters because they have no optics. The pulsed lasers have a very limited focal point and won't burn. But it will mess up your eyes though.
@@whiskeythrottle9369 I have a continuous laser, and you do have to be aware of how high your power is on certain things. It is the 1064. I do wear the safety glasses designed for it. As far as crossing my hand, no thanks, but this one does have a focal point, you can hear the difference in it when in use. If you get too close or too far away while using it, it’ll let you know. Just gotta have a bit of common sense.
youtube.com/@Laserguy660
@@whiskeythrottle9369 by the way, my laser is a 2000 watt. 👍🏻
Hello, Mike, so good video, thanks for your introduction for this machine:)
Thanks, Gloria. It’s an awesome machine and great fun to use.
How big of a air compressor is needed? And what psi is used? Thanks
Thanks for watching. For the cleaner, only a small compressor is needed. It's only function is to stop residues contaminating the lens. As long as there's an airflow over the lens, the vaporised material can't touch it. If you get a laser welder, you'll need more specialised equipment. I only have a cleaner, so I've not looked into the welding side.
Any suggestions on how much to charge for this service?
Good question, Eric. This is such a new option with the advantage of no mess. You still need to be competitive in your area, though. Look around to the pricing of sandblasting companies for paint and rust removal, graffiti removal, mould cleaning etc. Then charge more than that. Sell the fact you aren’t using chemicals or water or beads and there’s no mess. You’ll need to get those settings nailed, but that comes with practice and documenting. While you’re the only one in the area doing it, charge a premium while you can.
Hey Mike, thanks for the great video. I am expecting my machine from ACCTEC in the next few weeks and I was hoping you could give me some guidance with regard to stripping paint from wood. With a 1500 watt machine, what setting (power wise) should I be shooting for ? I don't want to burn down the building. Thanks in advance.
Hey Paul, good question. I haven't tested paint from wood removal yet. One of the things in the long list. You'll be aiming for low power and one of the patterns that prevent the laser staying on one spot too long. Getting the right settings is trial and error and loads of practice. It takes practice to get a feel for how high off the material to keep the laser and how fast or slow you move. Paint some scrap wood now, so when your machine arrives you can start experimenting and take notes of everything you test.
Would it clean housepaint off brick? I suspect it may be too hot for bricks causing cracking or fissures....
Good question, Robert. Laser works very well with paint on bricks. They’re used to remove graffiti on any surface. With the right settings, there is no damage to the underlying material. Laser also removes the soot from bricks and tiles after a house fire.
Hi again, would really like to know what its like on older car panels to remove paint and rust etc?
Really concerned of the thin metal on panels getting to hot and warping. A heat gun reading would be good if possible? Keen on getting one to help restore my cars. How has the machine been operating for you? What sort of water are you using?
Thanks again, it was a great video.
Hey Brenda, I can’t offer personal experience with old car panels. Maybe I can find some old rusty panels at the wreckers to experiment on and do a video. It’ll be a while though. I’m flat out at the moment. I use distilled water in the chiller. It’s a terrific machine, though I don’t use it enough.
Lasers of this type will absolutely warp car panels. You need a pulsed laser for that type of work and then you still need to be careful. And consider a laser a delicate brush. It will "paint" but very inefficiently so over large areas.
hey Mike thx .. I'm in the EU where there's a lot of stone buildings with discoloration due to types of lichen .. and I was wondering if you think this type of machine could clean this stone ? I know they're very expensive but this is just an idea ... thx
Yes, definitely the right tool for the job. I’d go with a 100W or 200W pulsed laser. It’s much smaller with lower power requirements than continuous wave like mine. For remote jobs you want an easy machine to move. The pulsed lasers are more expensive, but the technology means you get a lot more bang for your buck.
@@AussieMikesBees yes thank you for you advise !!
hello, sir, this is Gloria from ACCTEK company. Mike's sales, the laser cleaner machine clean the stone, and buildings is okkk:) and the machine price now is very effective, may i know your email address? then we can talk further, thanks in advance.
Looks like it sure would be handy to have . Great to see a new video Mike .
Thanks, Hank. It’s been so wet, I haven’t been able to do anything with the bees. Still waiting for an opportunity to transfer a colony into the long Lang.
Wow 😅 what will be the total costs of this fine piece of machinery?
Hey Pascal, thanks for watching. You’re best to contact AccTek for details. There are different models with a range of specifications to choose from. Mine was about US$7K plus shipping. They’ll arrange freight to your nearest port, then you deal with customs and last leg freight through a customs broker. It’s not difficult and way cheaper than buying a European or US machine.
@@AussieMikesBees Thanks 🙏
Very interesting. Thank you for sharing.
My pleasure! Thanks for watching.
Great informative video Mike! Thank you.
What power pulsed are you considering?
If I were to do it again, I’d most likely go for a 200W pulsed. More than enough capability, much smaller and low power consumption.
Hi Mike how is the machine going . Im considering grabbing one for commercial use. Do you think it would hack day to day use. Did you look at other chinese companies. Any advice would be greatly appreciated Mike. Thank you
Hey Nik,
My laser is going good, but I’m only an part time user. I have every confidence that it can handle full time duty. It’s a very solidly built machine. My experience with Acctek has been positive. They’ve responded to my requests for help whenever I’ve asked.
If I had my time again I would choose a 200watt pulsed laser. Much lower power requirements, portable and more effective than the continuous wave. I did look at other manufacturers and found they were a little deceptive about pricing. Acctek were straight with every detail: the deposit to start the build, final payment before shipping and the shipping cost and details. The only extra cost is local import fees, customs and transport from port to my place.
Mike
@@AussieMikesBees thanks for your reply mate. Yeah was considering the 200 pulsed laser but it does cost a few K more but my biggest worry is would it have the punch for heavier rust etc.
I was going to throw the 1000 in a van with appropriate gennie. But I can see the downside with gennie costs and moving the thing around.
Acctec are using your video in there promotion material. Just a heads up in case you are unawares
Cheers
Hey Nikky,
The thing with pulsed is they pack a punch above their weight class. Each pulse is higher power for short duration. I haven’t used one yet, but all I’ve heard indicates it’s more than capable of rust removal with lower risk of damage to the base metal. I think you would forget the extra outlay, when you have much lower power requirements and weight. Get a good fume extractor fo mobile jobs.
hello mike
just got my machine but the peaple at acctek dont give full infermation on full set up your video and replys are very helpful what size commpresor do you use and will the laser work with out the compressor attached. you give more infermation than acctek good job and also is the commpressor just for keeping contamanets away from lens or dose it have other perpase
Hey Jake.
The downside of buying Chinese at low prices is there is no training. The best teacher is experience and doing loads of trial and error taking notes on settings that work. I know people can fine tune these machines really well. I don't use mine everyday, so I've been surpassed by others that bought their's after me and you will too if you're making a living with it.
Yes, the compressor is to keep the lens clear of contaminants. I wouldn't run mine without it. You don't need anything special, just capable of the run-time you'll be requiring. Mine is a better than handyman, less than pro model that I use for my CNC router and CNC plasma and general use around the shop. I recommend a drier of some sort.
Hi Mike, great video and it's so refreshing to see real world workings of this type of machine unlike most other videos on RUclips showcasing laser cleaners. I'm going purchasing one of these machines and found supply companies in China interesting to deal with on a technical level. Wondering what your experience was with AccTech as these machines are a lot of money, have you had to chase after sales assistance and what is the quality like etc...
Thanks for commenting, Trent. I’m pretty happy with AccTech so far. They seem keen to keep me happy. Not that I’ve needed tech help so far. The machine works flawlessly. Gloria from sales touches base with me periodically. Not to sell me anything, just checking that I’m happy with the laser. I would definitely buy from them again. I have no affiliation with them. I don’t make any money on referrals or any other way with them. It’s my opinion based on my experience. I’ll be shooting a video of cleaning my very dirty stainless steel bbq (grill for the Americans). I think it will work very well. It’s one of those jobs I detest.
What company are you getting these from? I try to look into it, and it always asks for my email and information. I jist want yo know how to buy it
Thanks for watching, Jason. I bought mine from Acctek www.acctekgroup.com/laser-cleaning-machine/ through Alibaba.
Hi Mike, thanks for the video, it's great. Are you still happy with your machine after almost a year?
Thanks, Ollie the Collie. Yes, I’m happy with the machine. If I had my time again, I would go with a lower power pulsed laser. They are easier to work, smaller and lower power requirements. Down side - higher cost.
@@AussieMikesBees Thank you for your reply. Do you think you would also have better results with a pulsed laser than a continuous wave?
@Ollie the Collie I haven't used one yet, but from what I now understand of the technology, pulsed can be dialed in with precision to get amazing results on a wide range of materials. CW is sort of a sledge hammer - you can hit the pin nail gently, but it takes more effort to get it right than using a pin nail hammer. CW can put a lot of heat into the substrate if you're not careful and that could damage the part.
Nice demo! would have been cool to see how it worked with the paint on the shop pencil .
Like, if you could remove the paint and keep the laser moving around and limit, or not burn the wood of the pencil. Im wondering how this would do on furniture if your careful.
Good idea, I’ll do a video of various finishes on wood including the pencil.
@@AussieMikesBees Im not trying to bug you just a friendly reminder if any progress has been made to make a follow up video :)
Thanks for the reminder. I’ve been slammed for time lately. It’s on the New Years list.
Hi, have you used this machine on heavily rusted car panels, body or chassis? Also painted car panels? Thinking of buying a 1500 w machine. Appreciate any feedback? What state are you in? Thanks, Lee.
Hey Brenda, thanks for watching. Yes, the laser burns through thick paint and rust. It’s worth scraping loose material off first, so you’re only lasering bonded paint and rust. More power means more choices. You can turn down the power for thinner materials. Too much power can overheat and warp thin metal. It’s a bit of an art.
Hi Mike,
Is there any chance you could reply with link of where you bought this from?
I’m in Tassie and looking to buy one cheap enough to learn with before spending heaps on an expensive one.
Also, can you give details on the power pack your using,
Cheers, Paul
G'day Paul. I bought mine from Acctek through Alibaba www.acctekgroup.com/Laser_cleaning_machine/Fiber_laser_cleaning_machine_for_metal_1000W_5156.html
Not sure what you mean by power pack. I use a 32A outlet that I share with my CNC plasma (running one machine at a time). Although the laser has a 32A circuit breaker, I believe it might be possible to run it on a 20A outlet.
Tried this link but no longer working. Just trying to see how much you paid in US dollars. Thanks!
Hi Mike cool video. I'm from Brisbane and am considering this as a business. I have a couple of questions hopefully you can help me with. Would not your 1000 model also fit into a van? How long is the cable Lead ? I see Acctec are using a part of this video to promote there products are you aware of that. What made you choose this company , I'm also considering DMK. Any advice greatly appreciated. Cheers
Very impressive ,thankyou for the video
Thanks for watching. I have another video in edit on laser cleaning stainless steel injection moulds.
I'm sure it's gonna be hard to get an answer as you look to be a very busy man. I'm VERY interested in this company just worried about shipping, was everything shipped at a decent time?
I had no problem importing this laser to Australia. Acctek arranged the shipping to Sydney, then I was contacted by an import agent who organised customs. I paid them the fees and taxes, then picked up from the port. They would have arranged trucking from port to me too, but it was easier for me to pick up. You pay a deposit to start the order, then when the laser is ready to ship, they invoice the final payment. I did it all through Alibaba.
Hi Mike is yours the CV laser ? or pulsed ? and what did you pay for yours if Iay ask ?
Hey Anton, my Acctek laser uses a Raycus C1000RFL source which is a continuous wave CW. Check out the details here www.acctekgroup.com/Laser_cleaning_machine/Fiber_laser_cleaning_machine_for_metal_1000W_5156.html I bought mine through Alibaba and it was a smooth process. They are under $10K plus shipping and import fees. European and US machines cost five to nine time more.
Have you ever tried to remove floor finish off tile or wood floors
Thanks for watching. Good question. So far I have not done those surfaces, but I think that would be a good video. I’ll track down some test pieces and work it out. Cheers.
Hey Mike could you possibly paint a brick or a sandstone/ riverstone with masonry paint?? Give it a few coats let it really harden up. And try cleaning it off with the laser . I'd really love to see the prosses and the results. Cheers j the stonemason
Sounds like a plan, James. I’ll get a can of paint and put a few coats on some bricks and rocks. Might be a while before I get to shoot the video, kinda busy right now. Cheers, Mike
Hello mike how is the machine holding up, any problems and are you still happy with the machine? What did u pay for it if you dont mind me asking
It’s been a solid machine, although I had a minor glitch a while back. Turned out to be an interlock problem, nothing serious. If I had my time again I would get a pulsed laser. Smaller unit, lower power requirements, better performance. I don’t remember what mine cost, but it was way cheaper than the European or US brands. You can check current prices at Acctek on Alibaba.
Good video Mike hope to see more different cleanings
You think it cleans good enough to powder coat?
Good question. I don’t have any powder coating experience, so can’t offer a definitive answer. I know paint adheres very well, so I think powder coating would as well. The surface left after rust removal has a fine texture that I think help surface finishes bind better.
Hello Mike, You haven't got a video setting the laser up from scratch have you. Meaning from when you first plug the machine into the power plug then setting all of the perimeters right through to where you are ready to push the trigger. Enjoy all of your videos.
Hey Merv, thanks for the question. I haven’t done such a video, great idea. I’ll sharpen my pencil and put something together. The only videos I see tend to be Chinese factory demos and worksite videos with no commentary. That’s why it takes a while to learn how to operate.
Thanks for the video Mike! I actually ended up buying one of these recently and am about to get started with it... i had some quick questions for you though if you don't mind.
What is the jumper cable for? Is it simply attached to the gun to ground it? And did your machine come it or did you fashion it up yourself?
Thanks!
Thanks for watching, Mike. My laser came with the cable clamp attached. I couldn’t find a reference to it so I just leave it on the gun. It might be related to welding, though mine doesn’t weld. I don’t see a reason to earth the workpiece. I’ll ask next time a talk to tech support.
Cheers,
Mike
Goodcinfo m8keHi mike how much air pressure and volume you running,mine shows up in about a week,got a 2000w and 300w pulse on the way😊
I've been eyeing these for a long time, did you get yours from a a dealer or Amazon? Price? I'm hoping to get one for just under 10000 USD
Thanks, Matt. I bought mine from Acctek through Alibaba. It can be a little confusing when checking prices. Some only show the deposit amount, but it looks like the full amount. You should find a suitable model within your budget. Ensure you know the shipping and import costs too. I engaged an import agent to arrange for the import fees and local transport costs. The factory arranges the shipping from them to your nearest port and the documentation needed for importation. Pass these to your agent, pay the fees and the rest should be easy. If I had my time again, I’d consider pulsed laser and combination cleaner welder.
@@AussieMikesBees thank you for the detailed reply I really appreciate it! Never bought from Alibaba before but since you did and seem happy I think I would give it a whirl. Also I will look into the 3 in 1 combo that would be splendid, thank you sir!
I’ve bought several different items from Alibaba with no problems. Ask plenty of questions. They’re very responsive. There isn’t really anything on the training side, though. You’ll have to put the time in to experiment with the settings to get the best results for each material and coating. Create your own chart and keep adding to it with each new job. Maybe one day there’ll be a user group where we can exchange ideas.
@@AussieMikesBeesdid you mean to say Alibaba or AliExpress?
@@EasyFLtutorials Alibaba. AliExpress isn’t really set up for bulky, heavy items. I’ve bought many smaller items from AliExpress that use airfreight. Machines like the laser, honey pump and CNC plasma were sea freight and Alibaba seems to handle it better. You deal with the manufacturer instead of a reseller.
l have a ACCtek also very happy with the brand
Thanks for the feedback. What do you use yours for? Have you worked out the best settings for material you work on, or still fine tuning? Has it proved to be better than alternative methods. Have you had any problems with it? If so, what was your experience with tech support to fix it?
Hey Mike, placing my order next month for your exact model. How has your machine held up over the year? any lenses burned out and are replacement lenses obtainable?
I am beyond excited to join the laser cleaning game!
Hey Charles, congratulations on your machine. Mine came with a bunch of spare lenses and I still haven’t needed to change the first one. I’m not a heavy user though. Your experience could be different. Depending on your application, I’d consider going for pulsed laser in the 200W range. They perform very well and are portable with much lower input power requirements.
How much heat is created on the sheet metal?
Good question, Lee. It’s possible to put a lot of heat into the metal causing it to warp. The idea is to use the lowest power that vapourises the material being removed. It’s also necessary to keep moving the laser around the material to minimise heating one spot too much.
Hi Mike. From adelaide would like to have a chat about your laser cleaner?
Happy to talk. 0418441951
technically its a continuous laser or a pulse one?
Mine is a continuous wave laser.
@@AussieMikesBees Thank you! still thinking about wich one to choice. im going in China this weekenbd for that
Depends on your application. CW is like a sledge hammer. You can blast alot of deep rust using loads of power. It'll eat into the substrate too. It is possible to more gentle surface cleaning, but it doesn't have the fine tuning available in pulsed. Also pulsed machine can be much smaller for a similar effect. If you're going onsite to clean moulds or soot off bricks, remove paint from sheet metal then I'd go for pulsed. If you'll have a workshop where people bring their stuff to you for rust removal, maybe CW will do.
I'm sure the manufacturers will steer you in the right direction. Enjoy the trip.
Thank you for the advices and explications! ill try to find the good one at a good price. If you pass by Tokyo someday let me know, i hope my laser cleaning company will be already on the good way
I have one but the head overheats and the chinese are awful to deal with. They never answer any questions. Do you use compressed air when cleaning? If so what pressure
Thanks for sharing your experience. It’s a gamble buying anything from China. I’ve been mostly lucky especially with my lasers. I have no trouble communicating with AccTek for tech support. So far I haven’t needed parts, so have no comment about that. What brand is yours? I use about 90-100psi compressed air to prevent the lens being contaminated by smoke. My head has is cooled by the chiller. If the lines were kinked, it might cause overheating.
Every guy should have one. I'm gonna try saving some money to buy one.
Thanks for watching. Yes I totally agree. They’re handy for cleaning wife things, like burnt pots. So completely justified.
Lol got a small one. Works great but much slower than yours and can't be used handhelt sadly. Like your justification though ;-)
@@weekendstuffhow much was yours?
How much is it that machine?
Thanks for watching. I bought before everything exploded with Covid. For current pricing check with Acctek through Alibaba. You’ll need to factor in customs, taxes and internal transport above the shipping that Acctek arrange. It will still be massively cheaper than US or European brands.
Hi wish to know more about prices and suppliers in gauteng sa
Thanks for watching, Stephan. I bought mine from AccTek through Alibaba. They’re a pretty solid Chinese company and a fraction of the price of a European or USA machine. The flip side is no local training or support. If things go wrong you talk or email with the factory and get parts sent to you. I haven’t needed that yet, but Gloria from sales keeps in touch to see how things are going. Check current prices online. Watch it though, some companies advertise a really low price without saying it’s only the deposit. AccTek takes a deposit to start the order and the balance before shipment. They’ll tell you the full cost and shipping. You’ll need to sort import costs on your end.
Can you send me your contact at Acctek?
@@AussieMikesBeeshow much did your unit cost landed in Australia? I’m in NZ and have been looking at these. Great video too. 😊
@@AussieMikesBeesalso do you know the life of the lenses? Cheers
@@FHGWoodworking I think it might have been around AU$12K. I picked it up from the docks, so factor in domestic shipping. They supply a bunch of spare lenses. As long you keep the airflow, the lens doesn’t get contaminated. I’m still on my first one, but I don’t use mine full time. It’s a secondary tool for me.
Hello, do the machine need gas nitrogen or compressed air to work?
Thanks for watching, Christian. It uses compressed air to stop the vaporised particles contaminating the lens. I believe the welding version uses different gasses to match the metal.
Thank you very much Sir, excellent video. I really appreciate your answer.
@@AussieMikesBees
Hello howare you Sir, sorry to bother you again.
Which oil and water separation and filtering system do you use with your compressor to work with the laser machine?
Thank you.
I don’t use anything fancy, Christian . It’s not as fussy as a plasma cutter. Just a simple cartridge filter is fine. Obviously, if you already have refrigerated drier filter you might as well use it.
@@AussieMikesBees
Thank you very much for your answer Sir.
I recently bought a machine similar to yours 1500w. The Chinese sales representative told me that I need a drying and oil removal separator system for cleaning, for cutting and welding needs nitrogen.
I'll be sharing the results with you later.
Thank you for your help.
Best regards.
A guy could make some $$ cleaning tombstones with a portable version of that.
Good idea, David. There’s backpack models that might be good for that.
I've seen videos of laser cleaning on smoke damaged walls of a house. The laser machine was in the truck, power connected to the house, and a long hose with the handheld nozzle doing an effective job at a great distance. So this is 'portable' too.
I want one of these. I’d be spraying metal stuff in my garage with salt water….just so I could blast it. I’d also keep in it the back workshop area which I call “The laboratory “ where my wife is not allowed unless she accompanied by my dog, who I call my lab assistant, “J-Gore”….
I like your thinking, Norm..
Where did you get yours?
Thanks for watching. I bought mine through Alibaba from Acctek. There are quite a few manufacturers and can be difficult to know which to trust. My experience with Acctek has been good. They’ve been around for a decent time and have a broad range of CNC equipment too.
Chaps & chapesses, you really need to consider fume extraction & filtering. Some of the small dirt particles raised by these machines can be quite nasty, you wouldn't want them in your lungs!
Yes, agreed. I use a powered mask and blower. If I were in a populated area a fume extractor is essential. Any good welding shop extractor would do nicely.
Very true! It takes a woman to point that out. Thanks to us, most men are still alive today. So I find it very funny when they get all macho about their male skills and domains.
@@mjremy2605 oo...kay....
Awesome
Cost ?
I bought mine over a year ago and prices and shipping have changed. Look on Alibaba for current costs. Some vendors only list the deposit, so look out for full price. Way cheaper than European and USA machines.
is this CW model
Yes it is.
@@AussieMikesBees have you tried cleaning on wood with 10 percent power .
I don’t think so. For what purpose? Bare wood, painted, oiled, stained?
@@AussieMikesBees varnished wood .
I’ll add it to the list of experiments. So far I’ve only done metal and concrete, but various coatings on wood will be interesting.
can you help us make a good video?
Hi razertekcnc. What do you have in mind? Tell me about yourself and what sort of video you want. Mike
Pretty neat
Thanks, Thomas. I’ve only scratched the surface (no pun intended) so far.
@@AussieMikesBees Wire brushing and grinding the rust off my tractor wheels today for paint...kept thinking about that thing all day today. I'll put my wheels up on a big hill, point that thing at the U.S. and blast off the rust for me?
Sounds like a plan. We could FaceTime or Zoom so I can see what I’m zapping. Hopefully no birds or planes get in the way.😁
That's Chinese item not a guarantee 😂😂👌
While it’s true there is no local support for me, they have been very helpful online. Of course, you can pay three or four times more for a European machine with local training and service, but that puts it out of my budget.
All I know is I want to use that on a wasp's, or fire ant nest.
Now that’s a brilliant idea. Never thought I’d hope for a wasp nest to set up at my place, but bring it on.
Nice, but a RUclipsr can't buy or use that. But we can be jealous of how much money others have.
Yes, I watch some RUclips creators with insanely expensive equipment. I dream to have it, but I don’t have the time and often the skill to use it. Happy to be inspired by them sharing.
Men who color their hair are always a bit suspicious to me… Sorry ‘bout that….
No need to apologise. In focusing on that, you might have missed my other suspicious traits.