I've already programmed a key into a Megane with Renolink 1.87 EU, but didn't know the tip to let the door open. Last version is 1.99. Thanks for the information.
If I don't have any cards for the car at all and I get used 3 button cards and new transponders, can I just add them to the car? The only original thing I still have for the car is a transponder, but it is not recognized by the car, so I can neither open nor close it and I cannot turn on the ignition. If I find the cards again, I can turn on the ignition, but there are other transponders in it and I would now get 2 cards with the same buttons from a used car and swap the transponders in the cards and then teach them, I have to do each one Press card on Validate or only when I have put all the cards in one after the other?
how did you get a connection to the probe? I get rid of the red x but then I get this message Character spacing is invalid and cannot be removed. I just want to read the pin of the cards and then establish the connection for learning and programming and then after that has happened successfully cut the connection.
Hello, I did it the way you showed in the video for a Renault Espace 4, the cards were added to the vehicle and the vehicle can be started with both cards, but the central locking and Keyless Go don't work, I have to insert the cards into the card slot to start it. How can I check in Renolink whether the cards are running at 315 or 433 MHz? I also checked the door lock and the internal contacts are working, as well as the motors. I also replaced the sensor and attached new metal mirrors to the door handles, but unfortunately without success. Someone has an idea Best regards Kalle
@@KalleRenaud Hi , I believe you have problem with the key, it's not good quality, I'm sure you both from AliExpress and it happens many time to have this problems. Check also the antenna that reads the key signal.
@@YOYODiagnostic I have 2 original Keyless Go cards for my 2007 Renault Espace 4 that came with the purchase. With one card, the case was defective, and I opened it, then I lost the original pill, so I got a replacement pill and a new case. Now I have gotten the card where the chip was missing to the point where I can drive with both cards, but my Keyless Go and central locking no longer work with the card. According to the Can Clip, 2 cards have been read, but for the Keyless Go, it shows 0. How can I now add the maps to the Keyless Go? Can Clip says that all antennas are fine, the strange thing is when I park the vehicle and then after a certain time want to open another door, it only works if I put my hand in the driver's door handle and pull the handle, then you can hear all the doors unlocking, but this doesn't happen every time. When I drive at a certain speed, you can hear the vehicle locking the doors, and you can open and lock the vehicle using the switch in the headliner. It all works, including adjusting the mirrors, ventilation, child safety locks, window lifters, and the light at the bottom of the door. Didn't you also have a video where you explain with Renolink how to assign foreign cards to the vehicle by taking the VIN from the donor vehicle in Renolink?
Hello, I menage to program one new china card, but its only work to start a car not key lock. The card that before I use program was opening car ( but not start engine) now stop opening car and not recognise by computer program. Now I have 2card that start engine but no card that unlock car. I tried couple of times to reprogram, but renolink only recognise 2card (one is new) that start engine, but old 1card renolink dont recognise. What can I do to get opening car function back? Thank you
Hello mate I have Renault Zoe 2019 sealed the motor and inverter need’s both programmed to Ecu I have can clip what’s the best way to do it ?or could u do remotely?
That person is actually a scammer with the program. Sells the program to people on different platforms, than charges for the license separately in some cases. I could only get my license via the help of PayPal... The listing had the license, but the software I got with the device did not.
Can be just new key added to car, or you need to have all keys present while doing this process? Car is Clio Mk2. This part is confusing me. Thanks for reply.
1.You can program keys even if all are lost. 2.Another key can be added even if you have one present, but both must be learned because the old one will be deactivated after programming the new one, for this reason both must be learned.
Funktioniert es auch beim Renault Espace IV mit Keyless Go? Muss leider noch auf meine Bestellung warten. Mit dem Renault Clip braucht man ja ne PIN für nen Schlüssel anlernen.
@@YOYODiagnostic Hallo, wie versprochen bin ich wieder da. Also du kannst beim Renault Espace IV die Schlüsselkarte selbst neu machen. Ich muss nur noch rausfinden warum die Keyless Go und die ZV nicht mehr über die Karten geht. Auch kannst du deinen Kilometer stand per Renolink ändern, geht über extra und dann Tdb.
Hi! Thank you for the video Great stuff I Need to do what you did here on My Scenic2-2005. New (extra) Key. Can you point me to what hardware (OBD2) i need to connect to Renolink1.87? I Have downloaded already, will it work with Win10, or must I use Win7? Appreciate it! Best to you sir! David, Sweden.
@@Skinny-me Hi. I have a video dedicated to this programmer. I show you from where you can order the hardware and software, give a search, don't be lazy.
@@YOYODiagnostic Not Lazy Sir.. :) Just wanted to prevent bying something that does not work! I found A cable & software 2.10 on ETSY website for 60 Eur! Seems good, so I will go for that
hi dear friend, i comment you that my cards are disprograming include the original cards. you know how i can re programing my two cards? i have the original cards but this one is deprogrammed.
as far as I know with these cards it should work automatically if you order the right card. If you already have 2 keyless, the 3rd one won't work, you have to delete one from the memory.
I've already programmed a key into a Megane with Renolink 1.87 EU, but didn't know the tip to let the door open. Last version is 1.99. Thanks for the information.
👍
When I try to key programing,i finsh read pin and connect,but on start learning i get-7f3b22 Conditions not set or sequence error...Any help,thanks...
Great video man! Very helpful!
👍
If I don't have any cards for the car at all and I get used 3 button cards and new transponders, can I just add them to the car?
The only original thing I still have for the car is a transponder, but it is not recognized by the car, so I can neither open nor close it and I cannot turn on the ignition.
If I find the cards again, I can turn on the ignition, but there are other transponders in it and I would now get 2 cards with the same buttons from a used car and swap the transponders in the cards and then teach them, I have to do each one Press card on Validate or only when I have put all the cards in one after the other?
way you cut video 0n 3.09 the most important part, how we solve 7F8022 Conditions not set or sequence error
Hello friend, what is your cable(OBD)? Do you have a link?
Does it have to be a Reno link cable?
Great video! Does this work for megane mk1? I have cabrio 1997.
@@LambeLab Hi . Yes
Hello Interface disconnected by me how did you install that renolink?
Thank you.
how did you get a connection to the probe?
I get rid of the red x but then I get this message Character spacing is invalid and cannot be removed.
I just want to read the pin of the cards and then establish the connection for learning and programming and then after that has happened successfully cut the connection.
Hello,
I did it the way you showed in the video for a Renault Espace 4, the cards were added to the vehicle and the vehicle can be started with both cards, but the central locking and Keyless Go don't work, I have to insert the cards into the card slot to start it.
How can I check in Renolink whether the cards are running at 315 or 433 MHz?
I also checked the door lock and the internal contacts are working, as well as the motors. I also replaced the sensor and attached new metal mirrors to the door handles, but unfortunately without success.
Someone has an idea
Best regards
Kalle
@@KalleRenaud Hi , I believe you have problem with the key, it's not good quality, I'm sure you both from AliExpress and it happens many time to have this problems. Check also the antenna that reads the key signal.
@@YOYODiagnostic I have 2 original Keyless Go cards for my 2007 Renault Espace 4 that came with the purchase.
With one card, the case was defective, and I opened it, then I lost the original pill, so I got a replacement pill and a new case.
Now I have gotten the card where the chip was missing to the point where I can drive with both cards, but my Keyless Go and central locking no longer work with the card.
According to the Can Clip, 2 cards have been read, but for the Keyless Go, it shows 0.
How can I now add the maps to the Keyless Go?
Can Clip says that all antennas are fine, the strange thing is when I park the vehicle and then after a certain time want to open another door, it only works if I put my hand in the driver's door handle and pull the handle, then you can hear all the doors unlocking, but this doesn't happen every time.
When I drive at a certain speed, you can hear the vehicle locking the doors, and you can open and lock the vehicle using the switch in the headliner. It all works, including adjusting the mirrors, ventilation, child safety locks, window lifters, and the light at the bottom of the door.
Didn't you also have a video where you explain with Renolink how to assign foreign cards to the vehicle by taking the VIN from the donor vehicle in Renolink?
my open door sensor is not working(the door is closed all the time) and about 2 month ago i programmed a key and there is no problem!
Is it possible to program a new keys when the original one is not working ?
Hello.
Yes . You don't need the original key.
Hello,
I menage to program one new china card, but its only work to start a car not key lock.
The card that before I use program was opening car ( but not start engine) now stop opening car and not recognise by computer program.
Now I have 2card that start engine but no card that unlock car.
I tried couple of times to reprogram, but renolink only recognise 2card (one is new) that start engine, but old 1card renolink dont recognise.
What can I do to get opening car function back?
Thank you
Hello mate I have Renault Zoe 2019 sealed the motor and inverter need’s both programmed to Ecu I have can clip what’s the best way to do it ?or could u do remotely?
You need CanClip
good work bro
Thanks 👍
Respect Gabi Gafu !
Hello
This is true. Does a great job with this program. 👍
That person is actually a scammer with the program. Sells the program to people on different platforms, than charges for the license separately in some cases. I could only get my license via the help of PayPal... The listing had the license, but the software I got with the device did not.
Can be just new key added to car, or you need to have all keys present while doing this process? Car is Clio Mk2.
This part is confusing me. Thanks for reply.
1.You can program keys even if all are lost.
2.Another key can be added even if you have one present, but both must be learned because the old one will be deactivated after programming the new one, for this reason both must be learned.
@@YOYODiagnosticThanks for clarification.
@@JosipBasic ,,👍
@@YOYODiagnostic I have lost all key cards for my Mégane 2, could you explain how to code a new key with no keys available, thank you😊
@@Irritatedcodm ist the same procedure 👍
What happend between 3:06 and 3:09? Im Stock AT 3:06...
secret
Funktioniert es auch beim Renault Espace IV mit Keyless Go?
Muss leider noch auf meine Bestellung warten.
Mit dem Renault Clip braucht man ja ne PIN für nen Schlüssel anlernen.
Ich weiß nicht ob es funktioniert. Ich habe nicht probiert.
@@YOYODiagnostic ich werde es Probieren und dir dann Berichten.
@@kaller.9440 👍
@@YOYODiagnostic Hallo, wie versprochen bin ich wieder da.
Also du kannst beim Renault Espace IV die Schlüsselkarte selbst neu machen.
Ich muss nur noch rausfinden warum die Keyless Go und die ZV nicht mehr über die Karten geht.
Auch kannst du deinen Kilometer stand per Renolink ändern, geht über extra und dann Tdb.
@@kaller.9440 👍
Hi! Thank you for the video Great stuff
I Need to do what you did here on My Scenic2-2005. New (extra) Key.
Can you point me to what hardware (OBD2) i need to connect to Renolink1.87? I Have downloaded already, will it work with Win10, or must I use Win7?
Appreciate it!
Best to you sir!
David, Sweden.
@@Skinny-me Hi. I have a video dedicated to this programmer. I show you from where you can order the hardware and software, give a search, don't be lazy.
@@YOYODiagnostic Not Lazy Sir.. :) Just wanted to prevent bying something that does not work!
I found A cable & software 2.10 on ETSY website for 60 Eur! Seems good, so I will go for that
Hi there! is there any Renolink V1.87 software available for free?
thank you so much this was realy helpfull
👍
What is the name of the program?
hi dear friend, i comment you that my cards are disprograming include the original cards. you know how i can re programing my two cards? i have the original cards but this one is deprogrammed.
What is the obd that you used?
OBD link
Did you insert new key at first?
Yes,it can do all keys lost. If you lost your key, no problem it can program the new one, but use original software from Gabi Gafu.
Renolink code inyector?
How to activate hands free on new key ? Is this possible with renolink?
as far as I know with these cards it should work automatically if you order the right card. If you already have 2 keyless, the 3rd one won't work, you have to delete one from the memory.
Renolink can run on windows 10? Or only windows 7?
I don't know.
Does it work in megane ii ph 2? (2008)
Hello.
Yes . 👍
excellent video, where can I buy renolink safely, also do I need to buy the interface?
Thank you
Hello.
I did a review with this programmer. Watch that video and you will find answers to all your questions. Do not be lazy!
I have error:
7f3b22 conditions not set or sequence error
You are using a clone or the original?
@@YOYODiagnostic I have the original OBDlink SX with Renolink activation.
It's strange that Renault Pin Extractor reports wrong ISK
It may be that in the case of Megane 2 ph 1 2004, you should choose Megane 2 ph 2? The Russian website wrote that it might help.
@@coyotus77
select Megane 2 Ph2, open the driver's door and turn on the hazard lights.