RV LED Under-Glow Installation | STEP BY STEP
HTML-код
- Опубликовано: 10 сен 2024
- 0:45 - General overview of LED placement
1:50 - Cleaning surface with alcohol
2:16 - Applying 3M promoter
3:23 - Where to attach LED strip on right side of rig
3:53 - Drilling hole through battery bay for wires
4:00 - Attaching LED strip to right side
4:55 - Attaching LED strip to left side
5:46 - Running side power leads back to battery
6:22 - Attaching LED strip to front
6:39 - Attaching LED strips to rear
7:59 - Running rear power leads back to battery
8:30 - Overview of completed installation
8:43 - Controller module we used
9:10 - Testing the lights
In this video we show you everything you need to know about BoogeyLights multi-color RV underglow light kit. Watch as we walk you through step by step how to install these simple LED light strips on the bottom of any rig!!
This installation uses 1 of our multi-color RV under-glow kits found here:
www.boogeyligh...
And 4 of our multi-color add on strips found here:
www.boogeyligh...
This was an In-House installation done at BoogeyLights HQ in Florence, KY!
Call 800-847-1359 or go to www.boogeyligh... to schedule your install today!
=============================================================
For more information about Boogey Lights installation resources please visit: www.boogeyligh...
And don't forget to give us a follow!
Facebook: / boogeylights
Instagram: / boogeylights
Twitter: bo...
Light em up and travel safe!
I ordered my RV LED Under-Glow for the Flagstaff E-Pro E20BHS by Forest River. My installation will almost be the same except instead of the longer strips along the side I needed shorter strips, instead of two strips across the rear I needed four strips across the middle/rear section, and I have an adequate flat area all the way across the front.
We appreciate the business (and measuring beforehand)! Give us a call with any questions during installation: 800 847 1359 - enjoy!
Nice.
Definitely want to do mine to.
😁👍👍👍
Much appreciated!!
These are bad ass. I want a set for my Thor Windsport
Much appreciated! Give us a call: 800 847 1359 or check us out online - www.boogeylights.com
These are super cool!
why didn't you show us how to find the power to bring it into the bay?
We ran 8AWG cable directly from the battery on the tongue of the trailer into the storage bay. We'll show that in more detail on our next video. Here's the wire we used for this installation: www.boogeylights.com/8awg-parallel-battery-cable/
Very cool!
What’s a typical install like this cost for a 42 foot fifth wheel? Parts? Labor? Etc.
Parts can range from $500-1,000 depending on options. Typical installation time requires 6-8 hours labor for perimeter under-glow. Here's a link for our Installation options: www.boogeylights.com/boogey-lights-installation-services/
What is the cost of these lights and what’s the cost of installation
Depends upon vehicle, design, controller, etc. here's a link for our RV price estimates: www.boogeylights.com/rv-led-light-kit-price-estimates/
How much did you charge to do this???
It all depends upon size and amount of lighting. Our full-perimeter underglow package starts at $679.99 for a 5th wheel setup. In-house installation typically requires 5-8 hours depending on vehicle: www.boogeylights.com/contact-us/
we have underbelly cover, how do we install with that being there?
We typically mount aluminum flat stock (www.boogeylights.com/aluminum-flat-bar/) or angle (www.boogeylights.com/aluminum-angle/) to the frame/underbelly. Give our technical support a call: 800 847 1359 (M-F 9am-5pm ET)
I would have loved to see the wiring but good video otherwise 👍🏾
What was that sealant you used to plug the hole? Just a RTV Silicone?
We always use Lexel on any in-house installations: www.sashco.com/products/lexel/
what is the power draw on a set up like this ?
Our standard multi-color under-glow (2 - 16' strips) will pull 7amps on the highest setting (bright white). General rule is 3.5amps per 16' LED strip at 12.6vdc
Wire nuts on 12v dc. No...
DIY application. Welcome to solder, heat shrink, etc.
Can you run the power and ground up to your battery
Yes, all of our lighting is standard 12vdc.
So you just ran the wire to the house battery up front?
@@dbl-BLeiby Correct. We ran an 8awg wire from the battery to our controller module mounted in the front bay. A 10awg wire would be sufficient as well.
How much does an install like this cost?
Typically $700-1k depending on options/setup. Fill out our RV Lighting Form with specifics on your installation (www.boogeylights.com/rv-lighting-suggestions/) or give us a call for a quote: 800 847 1359
Why have you not showed an install for a Volvo semi truck? Don't care about an RV.
Videos require extra time during installation. However, we plan on doing more moving forward.
What justifies your insane prices on just some LED lights?
Here is a link as to what makes our lights different than other cheaply made brands www.boogeylights.com/why-boogey-lights/. And please feel free to check out the hundreds of reviews on our website! Thanks for your interest!
@@BoogeyLightsLEDs "The LEDs and electronic components we use are of the highest quality manufactured to our specifications..."
What are those specifications precisely that justify a $299 introductory price. That's what I'm hoping to understand.
@@AUDIOMIND That passage is from the introductory paragraph on that page. If you continue scrolling you can read the 10 reasons our lights are different right below that. Here's a link to a video about the differences as well ruclips.net/video/vM6-LqNdi6k/видео.html. Hope that helps!