I have a 4 strobe setup and can’t get it to work right. What do you do with the other pattern select wires? If I connect as per the instructions that came with the strobes 3 of the 4 stay off.
@@Towman1151 I got mine on Amazon. Just make sure you get the correct one. Its either going to be a ground triggered switch or a positive triggered switch.. I went my wire color and it was wrong.
For the 3 wire strobes, there isn't any sync wire so they could get out of sync with each other if they are on for a while. The only way to fix it would be cycle the power or change the mode.
i have 8 mini strobe lights with only a negative and a positive wire coming out of the back, i have the same switch as your using in this video, i wired all 8 lights together negative to negative and same with positive wires, now i'm gonna wire the switch to the wires from lights, the white wire that comes out from the switch, if i touch that to the positive wires to the lights, will it change the pattern ??
Never use wire nuts in any vehicle application. Those leads absolutely should be soldered. I get that you figured for demonstration it would be ok to use wire nuts. But many people take demonstration videos such as this literally.
We would absolutely recommend soldering these wires for a permanent installation. We added a note in the description to make that more clear. Thanks for watching!
How would you do this if you wanted to do a three light setup? I'd like to have two switches: Switch 1 activates the whites and some ambers. Switch 2 activates the same whites and some greens.
Do i need a 2ead harness for this which includes a rely and fuse or just get only a fuse or do i just install as it is?
how do you alternate the sync of a diagonal light group? A criss cross light pattern...
Can yo show how to wire the 10 mode controller please
Where can I get that type of switch
I have a 4 strobe setup and can’t get it to work right. What do you do with the other pattern select wires? If I connect as per the instructions that came with the strobes 3 of the 4 stay off.
Do you sell the box separately ? I need 2 sets of momentary switches
We do, here's a link to our switches. bit.ly/3oirCFv
Where can I order one of those switches with the on/off and momentary together?
Did you find out where to get the switch from?
@@Towman1151 I got mine on Amazon. Just make sure you get the correct one. Its either going to be a ground triggered switch or a positive triggered switch.. I went my wire color and it was wrong.
@@Justin-tp3lr can you post a link to one I can’t find one
@@Towman1151 if you search around there are other types as well including hard wired types.
Where’s this switch? I don’t see it on Amazon either…
How do you stop them desinking tho on 3 wire led strobes please
For the 3 wire strobes, there isn't any sync wire so they could get out of sync with each other if they are on for a while. The only way to fix it would be cycle the power or change the mode.
Where does the module get its power from
12v source from car either a fuse tap or a wire run straight to the battery with an inline fuse and or relay.
The fuse is good
Connections seem solid but the module has no power
Where do I check for a power source to it?
i have 8 mini strobe lights with only a negative and a positive wire coming out of the back, i have the same switch as your using in this video, i wired all 8 lights together negative to negative and same with positive wires, now i'm gonna wire the switch to the wires from lights, the white wire that comes out from the switch, if i touch that to the positive wires to the lights, will it change the pattern ??
Never use wire nuts in any vehicle application. Those leads absolutely should be soldered. I get that you figured for demonstration it would be ok to use wire nuts. But many people take demonstration videos such as this literally.
We would absolutely recommend soldering these wires for a permanent installation. We added a note in the description to make that more clear. Thanks for watching!
My LED on my truck doesn't flash any more, the light just stays on when switched on :(
Simple fix or is it of to the auto electrical?
How would you do this if you wanted to do a three light setup? I'd like to have two switches: Switch 1 activates the whites and some ambers. Switch 2 activates the same whites and some greens.
Works in sets
When you’ve linked both together with the sync wires do you still connect the second light with the program wire or not?
incomplete video.