How to Replace an Electric Water Heater Element | DON'T MAKE THIS MISTAKE
HTML-код
- Опубликовано: 20 авг 2023
- Don't get caught in hot water! 🔥🚿 Learn the essential steps to replace an electric water heater element flawlessly in this video guide. Avoid a costly mishap as I walk you through the process, highlighting the crucial do's and don'ts.
Link to Product: amzn.to/3KnPOyd
OTHER VIDEOS:
🎬 VAN TOUR: • VAN TOUR | ford transi...
🎬 2 MINUTE VAN BUILD TIME LAPSE: • VAN TOUR | ford transi...
📺 Subscribe to the Channel: bit.ly/31tQDi8
📬 Email: vanheeradventures@gmail.com 
Хобби
🤣🤣 I'm absolutely gonna laugh at you !! I'm also gonna give you respect for venturing out of your comfort zone and doing the work yourself. That being said, if you don't fail at anything, you don't learn anything, so keep learning and soon you'll know everything you need to ! Great video !!
Great point!! Appreciate the watch!
Thank you thank you thank you!!!!
After watching this video I realized that I too have made the same mistake. If it makes you feel better… I made it twice 😢.
I’m going to attempt to get those freakin elements screwed in…
But once I do, I’ll be sure to fill it before firing it up:)
Seriously thank you. This is actually the first comment I’ve ever left in RUclips… I’m really that thankful:)
Man this is so great to hear. You're not alone!
I give you a thumbs up just for your watch. What a classic. Great taste brother.
whyyyyyy thank you :)
Never open the t&p value if you're doing work on an older water heater as it tends to get slightly corroded over time and sticks open if messed with which will cause it to continually leak causing you to replace it as well.
thanks for the help!
Some electrical advice for you and others watching: Always check both phases of your circuit to ground. It's possible to get a false negative if you're just checking phase to phase. Also, you need a proper nm connector where it goes into the water heater or better yet use an armored flex cable with the proper fittings.
Yes! Great advice.
Another way a dry-fire can occur is if there's an air pocket in the tank when the power is switched on. Perhaps your proactive and drain/flush the once a year or every couple years depending on the water quality to remove sediment buildup, and that's great and can extend the life of the tank. However when refilling the tank its important to open a hot water faucet, preferably the highest or farthest one from the heater until water flows steady without gusts of air, to be sure all the air is purged from the tank before restoring power.
Great tip! Thank you!
Actually the closest is fine when refilling. You want the furthest fixture when purging air from the supply piping in the house : )
Just had to replace mine on my new water heater, when i wasn't home my water main broke and then a pipe under the house decided to freeze and also break draining my water tank. Such a fun surprise to come home to lol
that's my worst nightmare
Our professional plumber did it…training someone working for him…so don’t feel bad.
That makes me feel better
2:25 Give it a quick twist and it comes right off... "UNLESS" your water heater has been in service for a couple years then that cheap screw driver assisted wrench you are demonstrating will just deform and twist out of shape.... at which point you have to buy a 1- 1/2" deep socket and use your impact driver.Your bottom element was spared because each element has its own thermostat, and only one element runs at a time. The top element turns on first to start the warming process. Once the water in the top half of the tank reaches the set temperature, the top element turns off, and the bottom element turns on to heat the rest of the water.
Thanks for educating!! Very helpful
I just did the same thing! Uhhh!
You’re not alone
Bro I know this is completely off topic and has nothing to do with the video, but you look like the flash from the TV series...
Look at the other comments, you're not alone on thinking this