Hello and thanks for the video. Can you tell me, please what pin on CPU on this board is door_check? Or where to find the schematics? dE error. Door luck, wirings - OK. Thanks.
Hi, nicely done you seem to know your stuff, maybe you could help me with my Samsung washer, it keeps cutting out randomly during washes - the washer goes completely dead and only way to turn it back on is by unplugging it for 20 seconds then when i plug it back in it comes on and starts the wash again - then cuts out again and again, it's mainly at times when the drum is spinning slowly just before the fast spin, it sounds like it tries to go into high speed but then carries on spinning slowly - after 2 or 3 attempts the washer then goes dead. but say 1 out of 10 attempts the washer will work perfectly - but the next wash always fails
hello, what is the current from the plate to the motor? I can't accept it, I flew through everything, there were two free connections. thank you very much for the advice
@@inventorgeant the screen turns off completely.. I press start and it works normally again for 1 hour and then it turns off.. visually, I did not notice anything burnt, inflated or similar..
@@inventorgeant the module was with an electronics engineer (Rimac group -Nevera cars) who says that the module worked without error for 5 hours but without load.. Is it possible that there is a "cold connection" somewhere under load?
Hi. I have the problem of drum not rotating. After a long time it display E3 error. The motor is tested good and brushes in excellent condition. All programs the same. It starts inputting water but no rotation at all until finally displaying E3 error. Please help. I’d be really grateful
Hello and thanks for the video. Can you tell me, please what pin on CPU on this board is door_check? Or where to find the schematics? dE error. Door luck, wirings - OK. Thanks.
Hi, If you can help? power supply failure. does not turn on. Changed ICE2QR2280Z but the same problem, what could be the reason?
Impressive!
thanks for watching
Hi, nicely done you seem to know your stuff, maybe you could help me with my Samsung washer, it keeps cutting out randomly during washes - the washer goes completely dead and only way to turn it back on is by unplugging it for 20 seconds then when i plug it back in it comes on and starts the wash again - then cuts out again and again, it's mainly at times when the drum is spinning slowly just before the fast spin, it sounds like it tries to go into high speed but then carries on spinning slowly - after 2 or 3 attempts the washer then goes dead.
but say 1 out of 10 attempts the washer will work perfectly - but the next wash always fails
hello, what is the current from the plate to the motor? I can't accept it, I flew through everything, there were two free connections. thank you very much for the advice
Hi friend, tkx for watching. I'm sorry i don't understand your question. If you can explain more. Thank you.
salut cotre contac scp
suggestion for Samsung - Motherboard model DC41-00203A turns off after 1 hour of operation ??
i ask if the washing machine show an error code at the display? if not if you can take a picture for the display at the moment when he stop.
@@inventorgeant the screen turns off completely.. I press start and it works normally again for 1 hour and then it turns off..
visually, I did not notice anything burnt, inflated or similar..
@@inventorgeant the module was with an electronics engineer (Rimac group -Nevera cars) who says that the module worked without error for 5 hours but without load..
Is it possible that there is a "cold connection" somewhere under load?
@@inventorgeant What is the marking and magnification of the microscope you use?
@@prkacro are you tray any other programe or same one avery time?
Hi. I have the problem of drum not rotating. After a long time it display E3 error. The motor is tested good and brushes in excellent condition. All programs the same. It starts inputting water but no rotation at all until finally displaying E3 error. Please help. I’d be really grateful
Same thing but with 3C error. New motor didn't help.
@@mikemaman1did you fixed it? change 3 relays on the board will fix