PAUT SETUP AND CALIBRATION ON MX2.

[@ulia7521]

Really helpful for beginners to understand paut calibration, great job brother 👏

[@ndtsolutions2823]

thanks

[@rajeshchandan8116]

Helpful video if any new technican stuck during on-site calibration
Can you share the video of foundation bolt inspection done by paut

[@ndtsolutions2823]

Thank You Rajesh Ji
Hope you are doing good.
We have noted your request on foundation bolt inspection. Within a weak it will be uploaded.

[@vaibhavbhise3751]

Really good for beginners

[@saipeddakota78]

Thank you brother very helpful

[@badreenathmunnaluri7019]

Nice video, now I understand about calibration
Thank you bro

[@Manojkumar-bw6ob]

Sir, thank you ....your video is very useful to us...plz make more videos

[@ndtsolutions2823]

please let me know the specific topic.

[@prudhvikumard7542]

Sir it's very good session for beginners and we are expecting what is the purpose of TCG , wedge delay selection of probe etc.. in another video's And Thanks for the Video

[@tuskthiru2931]

Nice and superb.
Please share TOFD setup and calibration.

[@ndtsolutions2823]

WILL DO SHORTLY

[@arun_pal_8242]

Thanks a lot for uploading helpful videos. 🙏

[@shalumall1210]

👌👌

[@mohdhaziq8333]

maybe for upcoming videos you can upgrade the microphone for good and clear voice performance sir...thanks...anyway very good tutorial..proud of you...

[@ivoconsulting]

Thanks so very educative

[@mdshafaiz207]

Good for very beginner
Overall nice video

[@arun_pal_8242]

Nice video

[@biprodashmandal3150]

Excellent video

[@HassanHassan-qp6pn]

Hi..
Thanks for your video.
Why you are making threshold very low. Will be getting more noise signals
It is 20 threshold I think good.

[@saddamhussainz1487]

Great

[@mushrufsardar6717]

Nice

[@meenatiwari9441]

Very nice Supar

[@Its_YJ]

thanks a lot sir

[@yasararafath2692]

Please share PAUT scan plan video sir

[@arun_pal_8242]

Please more and more videos upload

[@husseinalwan3028]

ask about , ERVW blocks (small, medium, and large block) , is coverd the piping diameter range from 3 inch to 20 inch and can we used these blocks for wedge delay and velocity calibration ??

[@ndtsolutions2823]

Hi Hussein Off course we can do the wedge delay and velocity calibration with ERVW block. If you can do TCG rest also can be done

[@meenatiwari9441]

👌👌👌😍

[@dots5501]

plz make the video for TOFD

[@ndtsolutions2823]

Your request is noted. We will make ASAP.

[@dots5501]

@@ndtsolutions2823 thanks for response

[@ArunSingh-fy2jt]

Dear sir I'm looking for PAUT course can't you help to me

[@ivoconsulting]

Nice one give me encoder calibration

[@AkashSharma-do7ov]

🙏🙏🙏🙏🙏

[@AkashSharma-do7ov]

Sir please hindi me bhi samja do

[@ndtsolutions2823]

Hello akash it will be difficult. but if you have any doubt in any particular segment i will try to explain you in personal. You can contact me any time

[@deepakrawat3216]

Only time pass not clear introduction

[@ndtsolutions2823]

Deepak thank you for your reply, you may please let know what else can be added

[@rajraj-vl7ct]

Rawat its good for begginers ..don't watch the RUclips for time pass..

[@yashgamers9608]

Why you guys not covering entire weld in PA1 see on land area in PA1 some more position is balance

[@BalakumarPaulraj]

Nice video

[@mangeram2731]

Great

[@ganeshvasupalli4658]

Nice video