How To Calibrate InMotion Electric Unicycles
HTML-код
- Опубликовано: 20 окт 2024
- Have you ever felt your pedals dipping forward or backward when turning or spinning your electric unicycle? Time to calibrate! We'll show you how to do it using the Forwarding and Turning Adjustment in the InMotion App.
Electric Unicycles supported: Solowheel Glide 2, Glide 3. InMotion V5, V8, V8F, V10, V10F
InMotion App: www.myinmotion...
Get plugged into the EUCO Electric Unicycle Collective at www.euco.us
Thanks very much! I didn't know the positioning it also work for changing the light effect pattern. Cheers
I have tried to adjust the pedal tilt. I tried anti spin button on and off, I tried forward tilt, backward tilt and holding it straight up and down . Also lifting it up in the air. Always get a ’return vehicle to the upright position’ error message. Can’t make any adjustment with slide bar. Any advice for someone who doesn’t know what they are doing?
recently change the fuse on my BMS and I put a new motherboard in my V 10 and now
When trying to connect the Inmotion app I’m getting a message code that says the current serial number is abnormal (but I’m putting in the correct number)and the app Function cannot be used temporarily? Any idea? 🤷🏽♂️
Oh man, that's it? Haha... after a few falls, my pedals tilt back a bit, and I swear they tilt in turns, but I never bothered getting right into it because I figured I'd need a level or some stairs at least. Just prop it up and hit calibrate... nice
Can we do this for kingsong S22 pro too?
Is this a guitar stand?
Is this why I am always turning left and have to fight to go straight or right?
In case of set up problems can the secrets be found in the operation manual? :-)
Hola si me pueden decir como se prenden la luces del monociclo v10f gracias vendiciones esque no se la berdad
I did it but with the wheel tilted backward, same as for firmware upgrade. Is that a problem? It looks like it was successful. Thanks
As long as it showed the success message and you are on the latest firmware, you're good to go! If the app is showing that you're still on an earlier version, try again tilting it forward this time.
Appreciate the answer! It did work. I did that prior to your video and the pics in the procedure was not clear on which side to lean the wheel on. Seems like both work ;-)
Thx again
I did all of that and still says failure?? Idk what else to do
Wheel keeps going forward.
Is this the same for the v11 ?
is this the same for the v12
Dude thanks
I did forward calibration and it succeded. Problem is that since then it looks like my wheel has constantly the handle button pressed (even when I am not pressing it). Basically the wheel does not self balance vertically. It has become dead. I am on latest firmware 2.28 and do not know what to do as I cannot use the wheel at all :(. Any help?
Hey Marco - go ahead and fill out the form in the following link so our engineers can point you in the right direction: www.myinmotion.com/pages/service
Done. Would appreciate an answer asap. My wheel has never worked properly :(
Confirming our engineer here at the US HQ got your request, so keep an eye out for his response. If he's unable to help you remotely, you'll need to reach out to your seller to ask about exchange or repair as we are only able to service US customers.
i Don't know whats wrong with mine and i already did all this and it didn't help. It starts to go backwards by itself… without me on it offcourse. i neveer had this before
You should adjust "Pedal horizontal adjustment" also. You might need to push on the anti-spinning button to be able to adjust this setting.
What stand is that bro
This one is my personal favorite for EUCs: www.amazon.com/Foldable-Aluminum-AGS8-Adjustable-Protection/dp/B06XPCNFRQ/ref=sr_1_17?keywords=guitar+stand&qid=1571254082&sr=8-17
-J
You make it wrong whell must be on "rear" mudguard frontlight UP. you give Frontlight down thats wrong. Or V10(F) dont care fron or back mudguard?
in this link official : www.inmotionworld.com/blog/what-is-zero-offset-calibration-of-inmotion-unicycle
in this link i dont understand this: Special Note: After calibrating the offset in this stationary state, your Inmotion one wheel unicycle will clear the body zero setting, so it is necessary to re-adjust the "zero offset", as what we said in the Part 1. How readjust zero offset after calibration on mudguard? explain please?
I believe that is referring to the pedal angle adjustment