Each column (strip of LEDs) is wired in parallel in this video, so the signal from the controller is controlling every column same way. That's why this demo doesn't look like a spectrum alalyser. To wire this up so each column can be controlled independently you need to wire the data line in series. The power lines (the outside two wires) can be wired from either end (or both ends for really long strips) but the data line should go from the controller to the first strip and be soldered to the end with the white arrow pointing "in", then wired from that same strip's "out" end (the white arrow pointing out), then from there back into the next strip's "in" end, then out from the same strip's "out" end into the next strip's "in" end, and so on. Freeze at 1:21 to see how this video shows the wrong wiring. Keep in mind that the SP107E controller shown here also cannot actually be used as a spectrum analyser ait doesn't properly divide frequencies and so cannot generate the values needed for the display. You would need to find another solution for that even after the correct wiring is set up. Hope that makes sense to anyone confused by the wiring shown here. If that's still confusing have a look at the following video that shows that even with the proper wiring the SP107E can't display an audio spectrum.ruclips.net/video/Tfhw17CAoiI/видео.html
friend. This scheme there just turn on the sound they start to flash? or do you have to connect your cell phone via cable or computer for the leds to start flashing??
2:34 i spotted an ant walking on left of screen lol 😂 Your channel is awesome btw! I found ur channel off a comment but i like diy and ur logo so came and subbed 👍🏻 edit. Such a satisfying video.
thanks for the video but why you didn't make it matrix wiring you will get more affects and you dont need to connect your mobile to SP107E there is microphone build in
I had no idea it was that easy. wow. I should have invented that little module myself; I was looking for something more complicated, dang. Off to Ebay. Thanks this helps. I have built these really sweet book shelf speakers and had them hooked up to a PC sound system. The main unit has the ported base speaker type of thing. I went and built an LED VU meter; simple 7 LED device. It worked great. I was thinking of adding one of these to each speaker. I played around with it for a month or so, never driving it too hard for fear the ohms were not correct. Then one day after extended play, walked in the room and the system was dead. Figures right? I looked up the Transistors and found the exact, almost exact amplifier on line, and ordered it. I tested it and it works reasonably well, not sure about the base, but it was not in a ported box. kind of distorted base. speaker jumps all over if I crank the base. question is what caused the previous amp to fail? the LED lights, wrong ohm speakers, all of the above, or just old age. how does adding LED lights to the speakers affect the amp? Is this doable? or this module that you have shown here can it be directly connected to an amplifier? Guess I'll figure it out. Thanks for this cool tip. I like it. nice job.
You've incorrectly wired the strips! those strips have an input and output what you have done is wired all the strips inputs to the controller. What you should have done is wire the first strips input to the controller then wire the first strips output to the second strips input and repeat for all strips.
@@MrCT2012 thats not possible. You will need other equipment to build real spectrum according to the music. Or Just wait if they invented another app and music receiver with real spectrum
@@shakilahmed6870 no not at all I just start playing with Arduino, my dream project is 7 band music visualizer with RGB strip when it will be done I will upload surely
Achha h bhai ji par wtps no bhi sath video m hi likh diya kro sab padhe likhe log nhi hote kuch hamari tarah ke hote h jo khridana ya apna kaam karna to chahte par unko imail or gmail or link dekhna nhi ata h
Sir can u supplying led series n pixel led bulbs for detail decorations. I am in need of raw materials. Please send me the catalogue n prices and also finished products. I want to purchase in bulk quantities.
U didn't get me in order for getting the spectrum analyser effect on that app u need to put segments , for eg 10 seg of 10leds don't need keep the data line continuous
beto hola, buena sugerencia, pero ese efecto que se ve en cada línea se vería en una sola al estar conectados en serie. Igualmente se podrían hacer cosas divertidas conectándolo en serie
mon Jita mmm si ocupas muchos Leds tendrías que usar un transformador, o bueno, creo que sí usar esos controladores de wish aguantan para bastantes Leds. Si usas arduino, si no te sirve para muchos
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
this channel is hit
Each column (strip of LEDs) is wired in parallel in this video, so the signal from the controller is controlling every column same way. That's why this demo doesn't look like a spectrum alalyser.
To wire this up so each column can be controlled independently you need to wire the data line in series. The power lines (the outside two wires) can be wired from either end (or both ends for really long strips) but the data line should go from the controller to the first strip and be soldered to the end with the white arrow pointing "in", then wired from that same strip's "out" end (the white arrow pointing out), then from there back into the next strip's "in" end, then out from the same strip's "out" end into the next strip's "in" end, and so on.
Freeze at 1:21 to see how this video shows the wrong wiring.
Keep in mind that the SP107E controller shown here also cannot actually be used as a spectrum analyser ait doesn't properly divide frequencies and so cannot generate the values needed for the display. You would need to find another solution for that even after the correct wiring is set up.
Hope that makes sense to anyone confused by the wiring shown here. If that's still confusing have a look at the following video that shows that even with the proper wiring the SP107E can't display an audio spectrum.ruclips.net/video/Tfhw17CAoiI/видео.html
what is VU meter? the strip different? I saw the strip looks a bit similar, how to differentiate them?
well said. the wiring is wrong here
Perfect! thx a lot :)
friend. This scheme there just turn on the sound they start to flash? or do you have to connect your cell phone via cable or computer for the leds to start flashing??
2:34 i spotted an ant walking on left of screen lol 😂
Your channel is awesome btw! I found ur channel off a comment but i like diy and ur logo so came and subbed 👍🏻 edit. Such a satisfying video.
The two waiver gose to?????
hey, can i use 12volt led with this it looks like your stepping down voltage to 5volt im guessing yes?
Love channel you got some support
Can i use the ws2811 and weld in the same way as the ws2812b? Thanks!
Thanks. Anyway, this is only vumeter, not spectrum analyzer, so it seems strange to have the columns organized like that.
Prob. It is happening because of volume differences in song gets bass boost or slowing down
But its difficult if you build spectrum analyzer
I disagree, looks cool still.
@@deafmouse- Yeah, agreed, looks nicer than a single strip VU meter.
how many leds ws2812b can support this controller? or what's the maximum amperage draw of this controller?
Bro kya isko 65w ke home theatre se chela sakte hai
Amazona! 👏🏻
how many leds you can put in the same row?
thanks for the video but why you didn't make it matrix wiring you will get more affects and you dont need to connect your mobile to SP107E there is microphone build in
can you make that strip lights to wireless all of them by using bluetooth something so that strip light can be put anywhere in corner hop you got me
Nice work man🤟🤟
Thanks 🔥
Pretty cool. I think I might have the stuff to make one of these.
Why do you use a 2812 rather than a 2811 LED? Is 2812 better?
which power adaptor did u use in this one
very very helpful from other video on youtube..thank a lot...thankyou friends..
You are most welcome
where 4m you? i m 4m India..
Mas pq as.barras estão todas.acendendo por iguais não deveria oscilar
Did these products will delivered to India please reply
yes
where can I get this kit, it is great...
Is it important to have those many lines or can I have just 2 lines of LEDs? Please reply soon.
'
wow i like that color LED audio sound
Is it left right stereo or just Mono. How to do separate led bar strip for left / right speaker .
sackan18 its mono
Use two modules and wire left hand set of strips to one and right hand set to rhe other.
Bri may i know its power supply rating needed?
Hi i love this but im not sure about the late black and red wire go's
Can i directly connect it to speaker output ?
I had no idea it was that easy. wow. I should have invented that little module myself; I was looking for something more complicated, dang.
Off to Ebay. Thanks this helps.
I have built these really sweet book shelf speakers and had them hooked up to a PC sound system. The main unit has the ported base speaker type of thing. I went and built an LED VU meter; simple 7 LED device. It worked great. I was thinking of adding one of these to each speaker. I played around with it for a month or so, never driving it too hard for fear the ohms were not correct. Then one day after extended play, walked in the room and the system was dead. Figures right? I looked up the Transistors and found the exact, almost exact amplifier on line, and ordered it. I tested it and it works reasonably well, not sure about the base, but it was not in a ported box. kind of distorted base. speaker jumps all over if I crank the base.
question is what caused the previous amp to fail? the LED lights, wrong ohm speakers, all of the above, or just old age.
how does adding LED lights to the speakers affect the amp? Is this doable?
or this module that you have shown here can it be directly connected to an amplifier? Guess I'll figure it out.
Thanks for this cool tip. I like it. nice job.
Bro you invited this vulizer it's work or not plz reply
Do u have this piece for sale ?
Muy bueno felicidades por ese trabajo y por compartir tu experiencia saludos desde Florida USA
leds seems to be diffused, how did you do tht?
You've incorrectly wired the strips! those strips have an input and output what you have done is wired all the strips inputs to the controller. What you should have done is wire the first strips input to the controller then wire the first strips output to the second strips input and repeat for all strips.
then it will have separated spectrum by using the same controller is it?
No. You are wrong. He intended to connect strips in parallel so they have the same ups and downs. Gets?
@@rigidhammer7376 How if want to see separated spectrum?
@@MrCT2012 thats not possible. You will need other equipment to build real spectrum according to the music.
Or
Just wait if they invented another app and music receiver with real spectrum
@@rigidhammer7376 what equipment to build real spectrum according to the music?
How do I change the vu meter effect?like top to bottom, bottom to top,middle to top and bottom.
Hope you get my question.
by the app
@@pitu-s which app?
@@shakilahmed6870 the app you will get by the controller
@@pitu-s thanks...you build it?
@@shakilahmed6870 no not at all I just start playing with Arduino, my dream project is 7 band music visualizer with RGB strip when it will be done I will upload surely
What is the name for the led wire
Achha h bhai ji par wtps no bhi sath video m hi likh diya kro sab padhe likhe log nhi hote kuch hamari tarah ke hote h jo khridana ya apna kaam karna to chahte par unko imail or gmail or link dekhna nhi ata h
Hey creator, I connected all of the things correctly as this video but
it's not working noh, Can you help me
Perfecto 👌 👌 👌 👌 👌
Super ✌️👷♂️
what color is the led strip or model
Bro uska height Kitna hai ? Kaun sa application mobile mein plz reply me
Bro ye project maic se karke dikhao
Matlab withaut mobail connecting mic se song lekar led flash kare
Ager nahi samjha to
Call 7058124843
I want to connect i too pc what should I do
My dear, do you think this analyzer faithfully respects the frequency bands?
Yes, the music is just overlaid. His favorite music is "rhythmic white noise"
Sir can u supplying led series n pixel led bulbs for detail decorations. I am in need of raw materials. Please send me the catalogue n prices and also finished products. I want to purchase in bulk quantities.
What power adapter did you use for this?
ffxggtf
Looking for advice on a similar project I'm stuck on if any good Samaritans could help I'd be appreciative. Hard for a noob jumping into this stuff.
I'm using this controller , but not working properly. I want same model . How to change same as. Wt do do. Plz help me sir
Hey DIY builder did you just soldered the next strip to previous strip. Like yoh soldered it on top of the soldered strip already?
what is this application?
Sar aise saman kish market se milegha
Very nice
Me podrías pasar el link de donde lo puedo conseguir
Por que estaran de moda las canciones con voz de ardillita? 🤔
Dis you program it?
If you want like a spectrum analyzer (but not totally) you should cut leds in different sizes.
You got the idea? 😊
U didn't get me in order for getting the spectrum analyser effect on that app u need to put segments , for eg 10 seg of 10leds don't need keep the data line continuous
Ya item khaa mil saktaa h
Very good work bondhu....cary on....
Keren kak👍👍👍
Thought that it's gonna be a spectrum analyzer
I am working on it
@@DIYBuilder and how are you doing? it would be very cool!
@@denisratskov
ruclips.net/video/GtKIkkLkrwU/видео.html
What kind of power supply do you need for this?
5V 3AMPS
Parabéns pelo belo trabalho quê fez e ainda deixou os links de aonde comprar os materiais. Seu mais novo inscrito de Salvador/Bahia-Brasil...
Você comprou os produtos? Conseguiu montar?
Nice circuit
how to do it by sound frequency, the led lights are all the same levels
it's coming soon
Video LED Ws2812b 30ıp65 ? İp70 ? Op 140? which model, there are many models, thank you
What power supply did you use?
good Super
Thank you
Sugerencia, si lo conectas en serie seria mejor, ese controlador tiene diferentes funciones y no solo que prendan igual saludos
beto hola, buena sugerencia, pero ese efecto que se ve en cada línea se vería en una sola al estar conectados en serie. Igualmente se podrían hacer cosas divertidas conectándolo en serie
@@keilotalvarado cuantos leds soporta el controlador , o sea una sere
quiero hacer el proyecto de 2 controladores , o sea estereo , y 27 leds por canal, se podra
mon Jita mmm si ocupas muchos Leds tendrías que usar un transformador, o bueno, creo que sí usar esos controladores de wish aguantan para bastantes Leds. Si usas arduino, si no te sirve para muchos
Прикольная светомузыка надо тоже собрать👍👍👍
не получится, она не будет работать, автор не полностью все раскрыл, да и к тому же контроллер такой нигде не найти
Epileptic light.
The transistor lights go out smoothly and move to the next lamp.
How long is this LED stripe?
rgb controller buy where?
Bro I need to do this in exhibition in school
So plz teach correctly
In which we should solder
Plz reply...
the way it is made, it would never function the way it is shown
if you use in pc make sure you use another usb power supply such as phone charge .do not plug the usb power to your pc..it can cause ground looping.
It work with sound sensor?
Apakah dia menggunakan adaptor lg?
Circuit ka naam to bataiye
is code are needed ?
Nice
There is almost NO DIY here. You just assembled a kit...
This is not kit at all. He just glued led strip to acrylic and connect to controller. In kit you can atleast solder resistors, capaciotors, chips.
F*ck ya bich
@@DimaLegoFUN yes it
Shauna Antony someone with more experience than you
It's not DIY unless you mine the raw materials for the wire, fabricate the silicon chips and so on
the sp107 does not work as a led panel. use only one ribbon
but where is the speaker ? got no detail setup here
Saya pesen bisa om buat gabungan salon, sound
ekta BT module lagay dawal a lagaile seiiiii lagggbe 🤩🤩🤩
Bhai eta Bluetooth diye chole. Tui light effects, colour, speed sob phone diye control korte parbi
Pls ws2811 LED strip to Bluetooth control
Just buy bluetooth music receiver in market
It's simple to add
U get bluetooth controlled
Can it be done with arduino?
yes
@@DIYBuilder I mean the matrix effects,
Can you give some info/youtube tutorials/ any web link? It will be pleasure
Nice...
The connections of leds are awesome. Thanks!
Ps: no adruino needed
How did you do it without an arduino?
Can I make it bigger and the more LEDs to it
Ta ligado errado, ligou em paralelo tem que ligar em serie
This mono or 1 channel its not 2 channels or stereo.
klw beli dmn itu tolong info nya y
Itu gak beli
Subscribe Now 🔻
ruclips.net/channel/UCsvNUZrSPpWIY37qQOvQ_rw
Oi amiho como e o nome dessa fita de led
Bai yeh led kaha se multi hai
If using a LED RGB strip type SMD5050, 3528/2835, can it work?
can I do this with arduino by any way?
Yes you can, the arduino can control WS2812B led strips however for the audio input you will most likely need a arduino shield to take in the audio.
@@JtagSheep WITCH TYPE OF SHIELD?
Não ossila diferente ?
Cara sambung di load speaker ikut irama musik
bro which soldering iron u use?
Xin hỏi cục phát đó tên là j jay mn cam on nhjeu ạ