So, used to seeing immature restorations that I had low hopes. But, this video is brilliant and looked at everything to make sure the engine works perfectly after restoration. I'm assuming- the better fitting piston and cylinder makes more power than before.
Awesome job brother. I also have pulsar 150 and I want to rebuilt its engine haven't seen someone doing clean work like this, how much cost does it requires to do so?
I think you did fine if it comes apart then you learn from your mistake and try again nobody learns without first doing great video keep up the good work
Do you find any difficulty in tying screws the exact amount at each side so you won't affect the engine or tighten a screw too much and it loosens the whole thing !?
You don’t clean the inside of a watch that doesn’t work with worn out gears and call it restored. Restoring an engine is making sure everything is to spec and it runs properly
Remo Peter he couldnt start it as he has not done a good job this engine will vibrate like hell when started, he has not set the timing of the balancing shaft and the scissor gear on top of it, this engine will vibrate itself to destruction soon and the whole bike with it
Palsar engines are so up to date at its time even till now. I ride a old 150cc it can reach 126kmph without any vibration because of the balancer and sessior gear
Viendo en 2024.... siempre me gusto este canal lo sigo de hace varios años y lo que me gustaba mucho era la musica y la voz del final, deberían volver al uso de las mismas 👋
Here's a useful tip- pour diesel inside engine, let it soke for 2-3 days, than disassemble the engine, it naturally cleans all the dirt & stuff, makes your job much easier.
Good job, but few suggestions 1. Lubricate bearings, gears and some other parts before installing. 2. Use proper tools. 3. Wash parts in the well manners.
Engine ka chalu hona jaruri hai khali part fix karke ya naya painting karne se jaruri nahi hai ki wo chalega bhi ekdum mast. To bhailog aage se engine start karke bhi dikhana. 😊😊
I am machanical engineer... I kno full engine working process.. like how fuel go inside how combustion take place how piston move how crankshaft rotate.... But again i ask question myself how engine works... 😂😂😂.. Its an amazing invention of man...
Curious where do you source all of your parts from? I've got a couple bikes I'm working on and can't find a lot of stuff. If I do find them they are super expensive from places like ebay or partzilla.
Scissor gear was not installed with proper tension, it is to be installed with two clicks in anticlockwise direction, and also match balancer gear's mark with crank's mark.
This video is incomplete until you fire the engine bro. I guess it will provide it a proper ending
Agree
Yeah
I expected that in the end engine will breath its life, but alas it didn't happened.
Agree
well as i can see the internal gears were not rusted or stucked
So, used to seeing immature restorations that I had low hopes. But, this video is brilliant and looked at everything to make sure the engine works perfectly after restoration. I'm assuming- the better fitting piston and cylinder makes more power than before.
Esti tare fac si eu mtoare dar. Nu piese asa micute B AFTA ln Meserie. %%%!!
You have given new life to that engine just how a heart specialist doctor does. It's work of an art, good job and keep it up.
zzcoxcocozcozcoczxosxozpzupzoxooxupzpgxoxpppxicocozoopoppozzzocozxxcoczoxoxoxozozzoz
Ozxfiodoxyoxpxzozpoxphzvozoocogzxzxoxizzzxxxizoxp0hozvoghgcxofpcozzozggzzpczoxpsfzdzocoxzozozzzszdpzzxizzpOzozpxzuopffFzxhixzzoozooxoxohziz
Bina timing milaye sisore gyr fiting wa wawa gajab fiting 😀😀😀
😂
14:03
right bro
SO MANY PEOPLE ON HERE CALL A CLEAN AND PAINT RESTORATION THIS IS REFRESHING TO SEE SOMEONE OF YOUR CALIBER DO A TRUE RESTORATION
Im from indonesia,and im always support this channel yuotube
you must start up the engine after restoration.
My cousin has pulsar 150 and it's fun to ride.👍👍👍
Awesome job brother. I also have pulsar 150 and I want to rebuilt its engine haven't seen someone doing clean work like this, how much cost does it requires to do so?
hey hii, may i help you..
8000/-
@@ranjanapawale3059how?
වටිනව අයියේ .
වටිනා උත්තර දෙකක් හම්බුනා.😍😍
The world's most beautiful thing is restoration and it is somehow equal to creation !
There is nothing to write about, just get to work! Good job. Regards :).
Installing the bearings dry Can damage/destroy them when you First Start that Motor
Pretty sure Emanual has built hundreds more engines than you have.
Xepreme is absolutely right.. I have worked on thousands of PULSAR DTSi engines in bajaj auto..
same with clutch discs
Bearings were already damaged by this hammering on inner raceway, so not an issue for dry start.
@Bia Tch it's true that he made the mistake
But he does the job
you want it cheap for a 150 cc bike?
go to him
you want it for your harley?
find a pro
samajh mein nahi aaya par dekh kar acha laga😁😍
I think you did fine if it comes apart then you learn from your mistake and try again nobody learns without first doing great video keep up the good work
you have restored a perfect engine
One day Bajaj company will see this. 🙂👌
Very good super bro good job 🤗
Bravo, am impress, merci from Québec, Canada
Hai bro I'm searching job for Canada any help me how to come to Canada and how searching job
Surgeon of machines.....👌👌👌🙏🙏🙏
Do you find any difficulty in tying screws the exact amount at each side so you won't affect the engine or tighten a screw too much and it loosens the whole thing !?
Da
Get a torque wrench.
@@varun009 a torque wrench, how do I know how much torque I should be applying ?!
@@laughahole397 why don't you go ahead and look up just what a torque wrench is and how it works.
wow cool,,the engine looks like new again...
OMG, hammering on new bearings, reusing the totally destroyed nut at 12:01, don´t use oil while assembling the parts......
at least he used a nylon hammer/
Very nice and appreciate all the efforts. Very good mechanic who never made any sound or took a breathe !!
Scissor gear is directly fitted without setting 😇
Yes bro he is mentel
Ur planning to make a 4 wheel mini from pUlsar 150 cc , even im doing it
Should of atleast wire wheeled the rusty crankshaft
Nice to see an almost died engine brought back to life. Good work!
Nice job. I'm sure it will run good with a new carb. Were the charge and pickup coils ok?
Amazing. Amount of effort that was put in 😍
You don’t clean the inside of a watch that doesn’t work with worn out gears and call it restored. Restoring an engine is making sure everything is to spec and it runs properly
may not have been worn out. maybe only had low mileage , but it's his anyway , he'll be satisfied.
@@zookster4701 yes
You earned my sub.
Well done bro
भाई मस्त काम करते हो मुझे भी अपने बाइक का करवानी है addres बता देना please भाई🙏🙏
Nice effort taken. Well done man.
Where this place please update..... I have discover 135 old engine... so am need restoration.
Kya baat hay...badi mehnat lagi
Do it with explaining each part so it is easy to understand
Good video i liked, shared and subscribed👍👍🔥
Gokart building. You should have started the engine for the satisfaction of completion of restoration.
Remo Peter he couldnt start it as he has not done a good job this engine will vibrate like hell when started, he has not set the timing of the balancing shaft and the scissor gear on top of it, this engine will vibrate itself to destruction soon and the whole bike with it
Excellent, mechanic, I am from Assam, India
I didnt notice any lubrication parts during rebuild? Dry start!
Doctor of abandoned motor ❣️👍
Oh man!. I don't know how he remember all the parts and fixed correctly.
This is called talent my friend.
@@sierrachief117 Plus he has the video to refer to
কোকিলের ডাক শুনলাম অনেক বছর পর।
আসলে সমাজ পরিবর্তনের নামে উন্নয়নের চরম পর্যায়ে যার ফলে অনেক পশুপাখি বিলুপ্ত 😔😔
for a Go kart project !! we also made a Go kart with Honda CBR 250 engine...
Very very very nice video Bhai gajab Maja aa Gaya Bhai........ AAP Bhi mera channel pradeep raajwaar Ko jarur dekhna Bhai
You didn't show scissor gear installation and timing
It's not a how to video man
@@perfectcell7995 Yes, but he showed most of the things so I told 😅
He installed scissor gear roughly
Palsar engines are so up to date at its time even till now. I ride a old 150cc it can reach 126kmph without any vibration because of the balancer and sessior gear
I am amazed at how you remember where every little part goes.
Thats the difference between a technician and Common man 😃😂
Отлично! Когда будем запускать?
What a talent broo.....Hats off to uh👌
Before placing the bearing in the crankcase, the seat must be heated.
degrease acetone sealant application
Pulsar 200cc ka video hai kya
We want part 2 of this engine .
Very nice and good to have you in India....nice video good knowledge love you brother keep it up☺️👍
i say it's gonna be on a go-cart :)
☺️ 🙂☺️ 🙂
Viendo en 2024.... siempre me gusto este canal lo sigo de hace varios años y lo que me gustaba mucho era la musica y la voz del final, deberían volver al uso de las mismas 👋
You're definitely working on a go kart..
Bhai aap kaha se ho
How much cost for full bore pulsar 150
1500
new bore -2002rs
reboring -700 piston + 200rs smoothening
Good job ❤️❤️
15:26 u missing seftmotor..
Here's a useful tip- pour diesel inside engine, let it soke for 2-3 days, than disassemble the engine, it naturally cleans all the dirt & stuff, makes your job much easier.
Happy he didn't use that nasty oil stuff during the assembly, heaven forbid you should get oil on those clean parts.
I smell lot of sarcasm
Hi bro 👋👋👋very good restoration 👍👍👍
Bro isme pistonringa aur sciccor gear wheel timing
I can watch this all day❤
"All day" ?? You're in desperate need of a life mate ..lol
he is using elbow grease. elbow tightening is no way to go. sorry man but i don't appreciate it. first learn the right way and then do it.
Great work and it takes great knowledge also. Very good
Do you ever forget where anything goes?
Everything is awesome......just 1 thing missing.....u should have started the engine
U should make 2jz restoration for your next video..
Who are watching this video in 2021 October 😊
He missed Scissoring gear settings
Good work !!😍👍👏
How to replace activa 3g scooter gear belt. I subcribe your channel. I hope your answer
What are those tools u have used? I want them 😍
You painted an air cooled engine? Wow. Also, not one bolt was torque. Half assed
Great restoration video without proper tools, Some of worn out nut and bolts not replaced...Hope he get to correct that in next videos
Start the engine lmao
Good work sir, nice vedio, ur Address,
Which paint did you use? Is it heat resistant?
kha se ho bhai aaplog
How much did it cost you considering you purchased many small components...
Good job, but few suggestions
1. Lubricate bearings, gears and some other parts before installing.
2. Use proper tools.
3. Wash parts in the well manners.
Все super, а мотор заведётся ?🙂
This dude knows his stuff...
No he dont any builder knows you gotta oil your stuff
Where is your workshop...?
Engine ka chalu hona jaruri hai khali part fix karke ya naya painting karne se jaruri nahi hai ki wo chalega bhi ekdum mast. To bhailog aage se engine start karke bhi dikhana. 😊😊
wow 👏👏👏👌👌👌👌🙏🙏
Bhai pulzer 180 kick laga saktey h kya
15:22 you forgotten motor fitting, 15:44 then you fit it👍
I am machanical engineer... I kno full engine working process.. like how fuel go inside how combustion take place how piston move how crankshaft rotate.... But again i ask question myself how engine works... 😂😂😂.. Its an amazing invention of man...
This man is simply phenomenal at polishing turds
Curious where do you source all of your parts from? I've got a couple bikes I'm working on and can't find a lot of stuff. If I do find them they are super expensive from places like ebay or partzilla.
Unbelievable 😳👌🏼👌🏼👌🏼👌🏼👍👍👍
engine chala ke dikhaye hi nai... fayeda itna sab kar ke... kya result aaya kaisa chal raha hai...ye sab bhi to dikhao
Con que tipo de pintura lo pintas?
Scissor gear was not installed with proper tension, it is to be installed with two clicks in anticlockwise direction, and also match balancer gear's mark with crank's mark.
Cant wait for the Go cart video....
Very interesting video, I enjoyed the work he has done.