Thanks for dumbing this down!😭 Absolutely no offense to anyone else who’s struggles with proffie. I’ve watched videos left and right and can NEVER understand the programming on proffie lol This is the best video I’ve seen so far🙏🏼
EPIC tutorial Obi-Dad! I can't wait to start customizing my Proffie saber fonts. Also I wanna share a tip. There are inexpensive rubber tipped tweezers "for hobbies" available. I use 'em for pulling batteries and SD cards as you did and even a stubborn chassis I have in one my sabers. These make it even easier to grab hold of stuff without slipping an provide extra damage protection. BONUS: No wives, girlfriends or moms when you get caught haha!
Ha, ha ha ha no way! I’ve been looking for some thing just like that! Because on the Anakin Saber, those tiny little metal pieces at the top are screwed in and I can’t get to them with my giant fingers. But I didn’t want to use metal tweezers and scratch them up. I will have to Google search them. Thank you so much.
Proffie is one of the most difficult to program. I leave that to kids that have the brain power to do that. I'm glad you have shown people how to instead change fonts the easier way. Just remember: Always back up your microSD cards before you do any changes. It can save you major headaches. PS: other saber font styles (Xeno, SNpixel, etc.) can be installed in most the same fashion. Some font crafters do fonts in packages to cover a wide range.
Great video. The move from leaving it as-is to elbow deep in Proffie is difficult and showing this is a great way to bridge the gap. As for the saber, a couple of things I've found so far. First, TXQ, the manufacturer is on its third version already. The first run had the dirty weathering look on the hilt. The second version has the dark anodized look. On the newest they have removed the hole and hex screw that is on the back of the hilt opposite the control box and instead hid it in the control box. I believe there are also some changes to the control box, but I'm not sure. As for the intent of what saber it is a replica of, I am sure the intent was to make a replica of the BOBF Luke saber. Anakin Starkiller on the RPF designed it with TXQ with the intent of replicating that saber (I think the screen hilt was resin). He specifically worked to replicate the angle of the cuts in the section above the control box area (there's a name for this part, but it escapes me). They are different than any other Luke saber before. TXQs belt clip is very wrong and the switch box is off, but the machined parts are dead on. Like you mentioned @halliwaxbasementbuilds has a couple videos about it. He has the first version. If you want to remove the anodizing from the newer ones you can't do it with steel wool like he does. There's a chemical that escapes me at the moment that will remove the anodizing. Someone used "Whink Rust Stain Remover" to do it I think.
Thanks for the compliment bud. You are right about all the fine details…. You sound super knowledgeable. I’m kind of… more of a plug and play guy. If it’s close enough, I’m pumped! 😆
Obi Dad. Huge fan of you videos and attitude! Thanks for what you do! I have been collecting sabers for a little bit and really just started playing with Proffie. It’s great. I, like most, started with Hasbro and then Disney. The. Upgraded to Neopixel with Xeno and SNpixel. Now have been playing with Proffie. I think if you did a deep dive into the SNpixel app, you would love it. For the small step of the the sound board, you gain with customization on the app. Flickers, hum are the easiest to make and will look better than what comes from the factory on Proffie. SNpixel v4 pro is coming out soon but the current is very nice. I think extremely underrated and will give you some more content to make. Idk if you buy your sabers but I’ve been getting them from TXQ directly. Save money and the difference between SNpixel and Proffie is only $20. Thanks again.
Thanks for telling me this info man. I appreciate it. I am actually planning on getting the artsabers Luke Skywalker lightsaber so I appreciate this. And I bet this will be helpful for others too
First of all excellent video. The easiest to go through step by step! I have the same exact saber from ArtsSaber Profile. Can I rearrange the fonts in order? I would like the one you just added as well as me to be the first font. I always wanted a true Luke sound from ROTJ one these things and I have no idea why they never seem to put the correct fonts on the character sabers for that character. Thanks in advanced.
Hey Jeff, thank you so much for the compliment. I really appreciate it. The only way to arrange the fonts in order is if you do the long and complicated reprogramming involving a data cable and a couple of computer programs. I like to have mine in chronological order as well, I know how you feel.
Do you know why my color of lightsaber didn’t change? I bought my first font from Kyberphonic ANI3. I replaced files in JURASSIC font (I also have proffie 2.2 Luke Skywalker from Artsabers). The sound changed but the color not. This tutorial is only for sound? Best regards
I saw you at Dallas expo I was gonna say hi but it looked like you were filming and didn't want to interrupt but me and my wife were the ones who asked Hayden Christensen to do our gender reveal
No Way!! Congratulations Man! 🎉🎉 you should’ve totally said hi, I was rushing around, though between autographs and photos. Only at the convention for one day. I was actually going to make a short video of your reveal with Hayden. 😃🙏🏻
@@FindingTheForce we were too lol only there for one day and I can't wait to see bro I told my wife that I watched your videos and you turned me on the plaques for props and I bought a plaque for my Signed Return of the jedi poster by Harrison Ford and they knocked it out of the park
@@FindingTheForce it still feels like a dream come true man I'm glad me and the wife got to share our gender reveal with some amazing Star wars fans like yourself and others
Well, thank you for such kind words, man, I am very lucky to have you as a subscriber. Super happy to hear that you got an awesome plaque from Harrison Ford. That must’ve cost a pretty penny, I remember seeing his autographs going for sale online. Good for you though, bro, I just purchased a Luke Skywalker from a guy who works with the autographed companies. Got a buy up those oldies while we can 😉
@@FindingTheForce yeah twincity was doing the Signing the minimum on a card by Harrison Ford was 950 I got a 11×17 poster for 1100 but definitely worth the money I'm going to get it professionally framed and I know man Mark hamill needs to do another Signing last one he did was back in 2017 in Orlando
If you go into the “Config” File within each additional sound font that you add to the SD card, can you permanently change the color in there? After following these steps everything works as it should except the color always goes back to default and won’t save when I change it by the color wheel. Thanks for any help!
Hey Obi-Dad Kenobi, Great job with the tutorial! The only question I have at the end of the video is it possible to have a profile lightsaber that only has the saber sound effects aka no fonts, tracks, quotes, etc. Basically I want a really expensive Hasbro Luke ROTJ saber except more accurate in size. Keep up the amazing work!
Ples help! have the exact same luke saber and when i open my chassis its the same as yours but my soundboard is slightly more toward the speaker and with tools and tweezers i cant even get a grip on the sd card. Is my board warped or something?
I bought a saber from Ultra Sabers and it didn't come with any sound. I don't want to send it back to them just to be charged a crap ton of money to add it. Is there a way to do it at home?
I have the Weathered ROTJ Saber from Artsabers but can't figure out how to get it to play the music files. Any chance you could help with how to do so? I reached out to Artsabers and no reply, and the instructions were confusing. I have the SN - Neopixel board.
I own this saber, but it’s the SN-4 version. Is there a way of getting that font on SN-4? If not, do you know if you can buy a proffie chassis to retrofit to this saber (to replace my SN-4)?
Hey Steve, that’s a good question. Sometimes you can access the SD card with a data cable, but I think that is a feature that has to be unlocked on the soundboard.
I have the same saber. Sometimes when I swing it, the blade flickers off as if it’s losing contact with the base. Am I not tightening the screw enough ?
Sorry buddy, this is for the Neopixel Sabers that have a specific soundboard Cole proffie, it’s very common amongst the reasonably priced sabers. It can just be tricky and very time-consuming to take the long route to programming them with their own sounds and blade effects this video is a shortcut 👍🏻
Voicelines and most music are absolutely the most annoying thing about these nice sabers. Cringey quotes from prequels at volume 900 when firing up a saber is irritating.
➡️ Best Luke Skywalker Neopixel Lightsaber For The Price!
ruclips.net/video/3MN6K_CpWl0/видео.html
More bots. Searching them and then reporting.
Obi dad is so cool and sweet. 😊
Thanks for dumbing this down!😭 Absolutely no offense to anyone else who’s struggles with proffie.
I’ve watched videos left and right and can NEVER understand the programming on proffie lol
This is the best video I’ve seen so far🙏🏼
GREAT tutorial! I keep hearing about Proffie being very hard to program, but this made it seem easy enough for even me to figure out
basically it's just copy and paste.
Absolutely love your enthusiasm and positive attitude in all your videos it's really refreshing!
I think your comment just made my day! I try to have that same attitude about Star Wars and in life. Lucky to have you as a subscriber
definitely one of the most helpful videos, you actually showed how to get the SD card out, I’ve been so confused about where it was
im glad you said not to share the files, you didn't even need to, and that's super cool.
EPIC tutorial Obi-Dad! I can't wait to start customizing my Proffie saber fonts. Also I wanna share a tip. There are inexpensive rubber tipped tweezers "for hobbies" available. I use 'em for pulling batteries and SD cards as you did and even a stubborn chassis I have in one my sabers. These make it even easier to grab hold of stuff without slipping an provide extra damage protection. BONUS: No wives, girlfriends or moms when you get caught haha!
Ha, ha ha ha no way! I’ve been looking for some thing just like that! Because on the Anakin Saber, those tiny little metal pieces at the top are screwed in and I can’t get to them with my giant fingers. But I didn’t want to use metal tweezers and scratch them up. I will have to Google search them. Thank you so much.
dudeeeeeeeeee thank you 1 year ago and still helping newcomers!!!!
Video also made following requests from viewers (myself included), isn't he generous? Thanks for that man, it'll help us 🙂
Oh man, thank you so much for that kind comment. I always make sure to come through for you guys. Thank you so much for watching.
Thank you so much Obi-Dad!!!
My pleasure Christian, thank you so much for watching 🙏🏻
Great tutorial. Just updated my SD card with Kyberphonic the return v2- so simple and works a treat. Many thanks
Proffie is one of the most difficult to program. I leave that to kids that have the brain power to do that. I'm glad you have shown people how to instead change fonts the easier way.
Just remember: Always back up your microSD cards before you do any changes. It can save you major headaches.
PS: other saber font styles (Xeno, SNpixel, etc.) can be installed in most the same fashion. Some font crafters do fonts in packages to cover a wide range.
grumpy v1 is my favorite too. I knew right from hearing ignition that it was gonna be my main font.
I have the Anakin ROTS saber from Artsabers. Learning a lot. This was helpful for when I’m brave enough to try it. 😂
“I’ve been looking forward to this” lol I was one of those people who asked for this!
Thank you so much Obi Dad! I needed this 👍🏾
That’s awesome, so happy to help, thank you for watching.
Great video. The move from leaving it as-is to elbow deep in Proffie is difficult and showing this is a great way to bridge the gap.
As for the saber, a couple of things I've found so far. First, TXQ, the manufacturer is on its third version already. The first run had the dirty weathering look on the hilt. The second version has the dark anodized look. On the newest they have removed the hole and hex screw that is on the back of the hilt opposite the control box and instead hid it in the control box. I believe there are also some changes to the control box, but I'm not sure.
As for the intent of what saber it is a replica of, I am sure the intent was to make a replica of the BOBF Luke saber. Anakin Starkiller on the RPF designed it with TXQ with the intent of replicating that saber (I think the screen hilt was resin). He specifically worked to replicate the angle of the cuts in the section above the control box area (there's a name for this part, but it escapes me). They are different than any other Luke saber before. TXQs belt clip is very wrong and the switch box is off, but the machined parts are dead on. Like you mentioned @halliwaxbasementbuilds has a couple videos about it. He has the first version. If you want to remove the anodizing from the newer ones you can't do it with steel wool like he does. There's a chemical that escapes me at the moment that will remove the anodizing. Someone used "Whink Rust Stain Remover" to do it I think.
Thanks for the compliment bud. You are right about all the fine details…. You sound super knowledgeable. I’m kind of… more of a plug and play guy. If it’s close enough, I’m pumped! 😆
Thanks for that really comprehensive tutorial. I'm just starting to learn about all the different sound boards, so this is very helpful.
THANKS Mr STAR WARS 👍👍👍👍👍👍👍!! I really enjoy watching all your awesome Star Wars videos
This is going to come in handy when i get the cal kestis saber :)))))))
ok gotta check if it works when i remoove that CRINGY voicelines ...
Obi Dad. Huge fan of you videos and attitude! Thanks for what you do! I have been collecting sabers for a little bit and really just started playing with Proffie. It’s great. I, like most, started with Hasbro and then Disney. The. Upgraded to Neopixel with Xeno and SNpixel. Now have been playing with Proffie. I think if you did a deep dive into the SNpixel app, you would love it. For the small step of the the sound board, you gain with customization on the app. Flickers, hum are the easiest to make and will look better than what comes from the factory on Proffie. SNpixel v4 pro is coming out soon but the current is very nice. I think extremely underrated and will give you some more content to make. Idk if you buy your sabers but I’ve been getting them from TXQ directly. Save money and the difference between SNpixel and Proffie is only $20. Thanks again.
Thanks for telling me this info man. I appreciate it. I am actually planning on getting the artsabers Luke Skywalker lightsaber so I appreciate this. And I bet this will be helpful for others too
you really deserve way more subs you make so good and enjoyable content i will probably buy this luke saber or the hero v1 from 89 sabers. :)
Thank you so much. I really appreciate your compliment. Lucky to have you as a subscriber. 👍🏻
@@FindingTheForce ty so much
You are a lifesaver dude thank you
Heck yeah, you are so welcome!! Thank you so much for watching 👍🏻
Great video helped me a ton
That’s awesome bud, so glad to hear that 👍🏻
Awesome video brother! Very helpful indeed
Thanks so much bro! 🙏🏻❤️
Great video! Thanks for the tutorial
You bet, appreciate the comment.
Top tip. Use scotch tape to tape a piece of ribbon to the battery. Now you can pull on the ribbon to pop the battery out
Yes!! thanks man, I forgot to mention that one. I was actually just looking around the house for ribbon the other day lol.
Hey obi dad kenobi, do you know how to change the programmed blade color with the sd card? I have a Mac book and can’t figure it out
All I want to know is where you got that cool folder full of Luke voice clips from TLJ.
Kyberphonic my guy... tell him FTF sent you 😉👍🏻
First of all excellent video. The easiest to go through step by step! I have the same exact saber from ArtsSaber Profile. Can I rearrange the fonts in order? I would like the one you just added as well as me to be the first font. I always wanted a true Luke sound from ROTJ one these things and I have no idea why they never seem to put the correct fonts on the character sabers for that character. Thanks in advanced.
Hey Jeff, thank you so much for the compliment. I really appreciate it. The only way to arrange the fonts in order is if you do the long and complicated reprogramming involving a data cable and a couple of computer programs. I like to have mine in chronological order as well, I know how you feel.
Do you know why my color of lightsaber didn’t change? I bought my first font from Kyberphonic ANI3. I replaced files in JURASSIC font (I also have proffie 2.2 Luke Skywalker from Artsabers). The sound changed but the color not. This tutorial is only for sound? Best regards
Thanks for this!
Thank you so much for watching. Feeling a little relieved that this is not common knowledge and everyone was not laughing at me. Lol 😉
Nice video, cheers fella
I saw you at Dallas expo I was gonna say hi but it looked like you were filming and didn't want to interrupt but me and my wife were the ones who asked Hayden Christensen to do our gender reveal
No Way!! Congratulations Man! 🎉🎉 you should’ve totally said hi, I was rushing around, though between autographs and photos. Only at the convention for one day. I was actually going to make a short video of your reveal with Hayden. 😃🙏🏻
@@FindingTheForce we were too lol only there for one day and I can't wait to see bro I told my wife that I watched your videos and you turned me on the plaques for props and I bought a plaque for my Signed Return of the jedi poster by Harrison Ford and they knocked it out of the park
@@FindingTheForce it still feels like a dream come true man I'm glad me and the wife got to share our gender reveal with some amazing Star wars fans like yourself and others
Well, thank you for such kind words, man, I am very lucky to have you as a subscriber. Super happy to hear that you got an awesome plaque from Harrison Ford. That must’ve cost a pretty penny, I remember seeing his autographs going for sale online. Good for you though, bro, I just purchased a Luke Skywalker from a guy who works with the autographed companies. Got a buy up those oldies while we can 😉
@@FindingTheForce yeah twincity was doing the Signing the minimum on a card by Harrison Ford was 950 I got a 11×17 poster for 1100 but definitely worth the money I'm going to get it professionally framed and I know man Mark hamill needs to do another Signing last one he did was back in 2017 in Orlando
Hey Obi-Dad, quick question, can you ADD more fonts?
or does Proffie restrict you to just the fonts on it and edit those?
More fonts can be added! Get searching for those ones you want as there’s some great ones out there.
Is it work the same with a two boutons lightsaber ? 😮
I got my anakin ep 3 replica proffie and i don’t have the anakin sound font or can’t access it
If you go into the “Config” File within each additional sound font that you add to the SD card, can you permanently change the color in there?
After following these steps everything works as it should except the color always goes back to default and won’t save when I change it by the color wheel.
Thanks for any help!
How do you activate the Force Effects with a ONE button Proffie Lightsaber Hilt ?!!
Hey Obi-Dad Kenobi,
Great job with the tutorial!
The only question I have at the end of the video is it possible to have a profile lightsaber that only has the saber sound effects aka no fonts, tracks, quotes, etc.
Basically I want a really expensive Hasbro Luke ROTJ saber except more accurate in size.
Keep up the amazing work!
You cannot change the pre-programmed colo(ur)s on a Proffie Lightsaber, right / correct ?!!
Cool
How can I add one if I don’t want to exchange it for one you used an Ordner that’s already there Is it possible to just add one ?
Does the proffie already have battle of heros installed inside
if i wanted to add a whole new font from kyber is just drag the whole file into the sd card?
Ples help! have the exact same luke saber and when i open my chassis its the same as yours but my soundboard is slightly more toward the speaker and with tools and tweezers i cant even get a grip on the sd card. Is my board warped or something?
I bought a saber from Ultra Sabers and it didn't come with any sound. I don't want to send it back to them just to be charged a crap ton of money to add it. Is there a way to do it at home?
Can I add sound fonts that I purchase this simple
Will attempt this 1 day ....thanks may the force b with us ......always 😂...or the farce...as it will b with me attempting this😂
I have the Weathered ROTJ Saber from Artsabers but can't figure out how to get it to play the music files. Any chance you could help with how to do so? I reached out to Artsabers and no reply, and the instructions were confusing. I have the SN - Neopixel board.
Hey, What About Golden Harvest?!
Cooooooooooooooooooooooool!!!
Haha thank you so much bud
Any thoughts as to why I can’t delete the files out of the SD card?
Figured it out, my SD card adapter has a lock switch and it was set to lock
Nice! Glad you figured it out. I forget that they have those sometimes.
When I replace an audio file (hum or font) with the same name and format, it doesn’t go through🥲 What would I have to do to execute it?
I own this saber, but it’s the SN-4 version. Is there a way of getting that font on SN-4? If not, do you know if you can buy a proffie chassis to retrofit to this saber (to replace my SN-4)?
I believe SN-4 boards read Proffie files natively.
Hey bud, that’s a great question. I would message Kyberphonic on Instagram 👍🏻
@@FindingTheForce thanks for the suggestion!
@@FindingTheForce Thanks for this! He replied within a minute to confirm that SN-4 reads proffie files!
I do SNv4 installs all the time and Kyberphonics Proffie ones are so easy to add to it. Just change the folder name to the next sequential number!
Can you program with a data cable or does it have to be SD card reader
Hey Steve, that’s a good question. Sometimes you can access the SD card with a data cable, but I think that is a feature that has to be unlocked on the soundboard.
I just took some wrapping tape and made a tap around my batteries for my saber. 😅 i dont want to damage anything lol
Obi dad is 🔥🔥🔥🔥🔥🔥🔥💯💯💯💯💯🥹🥹🥹🥹🥹🥹
Dude… so nice of you… thanks man. 🙏🏻
And also, anytime. may the force be with you my new friend. May we be friends?
Agreed...I'm really not liking proffie...if you can't change the fonts with out programming than what's the point.
I have the same saber. Sometimes when I swing it, the blade flickers off as if it’s losing contact with the base. Am I not tightening the screw enough ?
Mine does the same. Probably because of the lack of blade depth, it gets a little wobbly.
You showed how to change the font but how can you add a font
Quick tip, you can actually tap the battery out instead of pulling it out! It pops out pretty easily :)
👍
Why does everyones lightsaber have a micro sd card. My neopixel proffie saber never came with one
This changes for original Galaxys Edge dark sabers?
Sorry buddy, this is for the Neopixel Sabers that have a specific soundboard Cole proffie, it’s very common amongst the reasonably priced sabers. It can just be tricky and very time-consuming to take the long route to programming them with their own sounds and blade effects this video is a shortcut 👍🏻
Can I have your Plastic darksaber And a anakin plastic Lightsaber
7:15 - it MUST be a data one tho ; not a charge one!
Wouldn’t they have the right to sue you for pirating their sound fonts anyway if you shared them?
Voicelines and most music are absolutely the most annoying thing about these nice sabers. Cringey quotes from prequels at volume 900 when firing up a saber is irritating.
worst lightsaber in terms of components .... I own it sucks .... the blade does not stay connected correctly and is also crooked. Artsabers sucks
Artsabers resells sabers lol they def suck and the price too 😨
@@Tofu6969every lightsaber company resells lightsabers. You clearly haven’t done your research on the matter. The manufacturer would be at fault.
Not artsabers. The manufacturer.