Can-Am Outlander Rear Diff rebuild

This is a rear diff rebuild on a 2016 Can-Am Outlander 450. The pinion bearing on this one was worn out. This may be the same process for other can am models as well. I know the Diff looks very similar to the larger bikes but I am not sure if the internals are the same. #ad
The Diff tool that I made in the video is Can-Am Part # 529035649.
Link to tool
ebay.us/1O8bzM
The link to the bearing and seal kit off Ebay
ebay.us/qEJXSZ

[@epitt906]

Wish I live close to you, can learn alot hanging with you....Great job...👍👍👍

[@FourwheelerDoctor]

Thanks and thanks for watching

[@Dakota-ish]

Hey brother , just wanted to say thanks for guiding me through . I just wanted to add on my methods of getting the job done in a apartment !
-Bought a bearing a seal tap kit & seal puller tool from Harbor freight
-bought a 1-7/8 socket to tap pinion seal in
-bought a grinder bit for a dremel , cut the needle bearing on opposite sides , once i seen i cut all the way through , i took a screw driver and with one hammer swing she split in half and fell out . (Took me 5 mins for needle bearing)
-bought a 1-1/2 socket , took a dremel with cutting wheel and cut me a key socket for the pinion nut.( wanted to make one for front diff aswell)
To remove pinion bearing , i sat it bearing on 3 Deepwell socket , and hit the pinion through. And used 2 sockets to put new bearing back on .
You made this way simpler and saved me alot of time my man !

[@m.b8257]

I don’t think Canned Ham’s have the same quality as a Honda. Great video. Happy New Year!

[@TurmiteRS]

Too much horsepower and torque, that's why stuff gets worn fast lol

[@alansmith7950]

I think I am about to have to to this to my can am. Thanks for the video it will be very helpful. Really would enjoy borrowing them custom tools lol.

[@FourwheelerDoctor]

Thanks and thanks for watching

[@alanjahner-yl9uw]

Nice job just let ya know 1 1/2 “ square tube fits the 4 grooves on that pinion nut perfectly turn it out with a pipe wrench on the tube have a piece in my tool box for this job way cheeper than can am tool lol

[@FourwheelerDoctor]

Thanks man

[@LogicAppleby-zj2ep]

Doin one of these soon. Shouldn't be as much bother as this one.

[@636STUNA]

Need to get a blind bearing puller

[@loluspololus]

Great video !

[@thedudeinthestude6442]

I like the axle puller. I'll have to make me one.

[@FourwheelerDoctor]

They can be a life saver at times. I think I have three different ones for different size axles.

[@prospermlilo-mc1qt]

How to change diff direction? My bike is turning opposition way , if i put in foward gear the diff is turning the opposite side

[@md1120]

Hi, great video. I didn't see you change the ware ring on the drive shaft. I'm scratching my head working how to do this on the bike.

[@jakealexander5777]

These models don't have a wear ring. You have to replace the yoke. It's about 30 bucks.

[@matasm7818]

You didnt use screew glue? In manual written loctite🤔

[@racerx143]

It's not a rebuild if you're not checking / setting the preload and backlash. This is just swapping seals and bearings. Not the complete job being done.

[@bballracer92]

Where did you get that hoodie?

[@FourwheelerDoctor]

My good buddy gave it to me lol

[@MiguelFernandez-xw9kd]

Haphi new year