BATTERY MANAGEMENT SYSTEM | WHAT IS A BMS ? | LITHIUM BATTERIES ? | EXPLAINED IN HINDI |
HTML-код
- Опубликовано: 3 окт 2024
- FOR BEST EXPERIENCE WATCH IN 1080p
Support me by contributing-
Paytm-p-y.tm/P9-BHCr
UPI ADDRESS-parvgupta001@okaxis
This video is only intended for educational and learning purposes and does not promote any brand or any product,it is a non sponsored video.
I would like to give credits to the RUclips channels and other organisations whose video clips i've used in this video.
Hope you like my work and thus don't hesitate to share the good stuff keep spreading knowledge and do tell me what you feel about the topic in the comment section below.
TOPICS COVERED-
BMS
TYPES OF BMS
EBIKE BMS
BATTERY MANAGEMENT SYSTEM
LITHIUM BATTERY
ALTERNATIVE OPTIONS
This video explains about the aspects of the topic in a very brief way and does not include any paid promotional advertisement
It is intended specially for Indian audience and is in HINDI language.
Here are a couple of useful video links for further reference-
www.renesas.co...
www.jttelectron...
www.rec-bms.com...
3CELL 12.6V 25A BMS MODULE FOR 18650 CELL-s.click.aliexpr...
Battery management system: • What is a Battery Mana...
I started getting into DIY recently but I always thought or hoped of a Indian DIY channel by someone and finally found you. Keep more DIY stuff coming up it would be if it is more on electronics though :p Thank you.
Amazing.
Please clear we always connect parallel cells with series so how the BMS will control parallel cells to overcharge , over discharge etc . For example 3s 4p battery pack .
Thanks for sharing your knowledge
I have questions with respect to cell balancing please help me
1.when this cell balancing will occur is it when charging the battery or when any cell goes more then rated voltage.
2.can you please explain how changing in battery will happence
3. please explain how this scenario works
Suppose a battery contain 4 cell in it
0v is minimum 5v is maximum
3.5 is the normal operating voltage
If one cell goes to 1.5v and am using passive cell balancing method and remaining cell are at 3.5 voltage
Please explain when charging will happence and when cell balancing will occur
1. When cell goes more than 4.2v its ic dwo1 cuts off that cell
2 . To change entire battery just desolder and resolder the entire battery
In order to replace any single cell just complete one charge discharge cycle
3. Thier is individual cell monitoring not the battery pack as a whole so this problem won't occur in the first place
So it is certainly a problem with passive cell balancing thats why individual cell balancing is used in BMS boards
However if your cells are totally identical which is very rare then they won't drift apart much.
However i would have to say your questions were really great...
sir 14 ampere ki baterry hai 40 amp ka bms hai betrry me 9 volt currnet huta hai phr trip o jata hai ap batae bms zyada discharge kitna voltage huna chaiye
My friend.. when you upload some videos from another channel it would be good to put the URL of original video on descriptions...
Thanks for the reminder ,Sure will keep that in mind...
Hello young man, you have good knowledge and very good presentation skill.
Thank you
@@DIYININDIA Can I share your video on my Community tab for my subscribers?
Yes offcourse
can bms charge battery and supply voltage at the same time
bhai... lithium ion battery charger me mosfet switching kaise hota hai.? iska video bana sakte ho...
Bhai Apne Mere Dil Khwahish Poori Kar Di Mene BMS Ki Jankari K Lie Apko Msg Chhoda Tha .
Thanks Dear Bro . Apko Happy New Year In Advance 😊.
Thank you ,happy new year for more information about BMS be sure to check out the video description...
make more video on the battery management system
Sir me ne step up module lagaya bms ke 12 volt current ko stable krny ke liye lekin jesy hi step up module bms ke output pe lagaya to 12 volt se 0 volt ho gaya output sir please koi hal bta den
Sir this video is Crisp and Clear nice video. Kindly clarify my doubt. How to identify BSI and BTEMP on battery protection board ( batteries ). Some batteries are written as P- ID TH P+ in some battery protection board written as P+ SCL SDA p-. Please let me know what is SCL and SDL on battery BLP571
SCL is the clock and SDA is the data line used to connect to an external microcontroller this is the I2C communication protocol.
For the information about bsi and btemp refer to the datasheet of the board...
BMS can give cranking power starter motor two wheeler four wheeler ???
Bohat kob bohat lajawab
32700 battery 12amp me bms konsa lagega
Nice presentation helpful for me thanks
Good sense of explanation
Kya bms se 4brushless motor chala sakta hu
sir 18650 (3 cell)ko 30 amp bms se jod kar drone uda sakte hai
Internal resistance of 18650 is too high
It's not designed for such high current applications
You will be degrading the battery by doing so
Thank you for the useful links in the description.It was informative.
Thanks brother
Merry Christmas
What are the Design & development consideration of BMS?
How to make it for suitable application?
Waiting for your positive response.
Thanks
Bms are designed on pcb for application specific tasks and does the following as mentioned in video.
To design own customised Bms, industries use the specific ics according to thier requirements from several brands like ti or vishay and sometimes even fabricate the entire board ground up....
How do you select Which BMS capacity in Amps like 30A, 60 or 100 A to choose for eg 48V 250, 500 & 800 Watt Motor
thankx bro
jio hazaroon saal
Nice video sir thanks
भाई बैटरी पैक बनाने के बाद बैटरी चार्जिंग के लिए बीएमएस को इनपुट वोल्टेज मैक्सिमम कितना वोल्ट देना चाहिए
Battery voltage equivalent
A BMS is having 3 point , namely B-, P-, & C-. C- & B+ve is for charging port, P- & B+ve is for discharging/power port and B- connected to Battery pack -. But I purchased one BMS which is having only B+ve and PACK-, the single port come out for charging and discharging/power as I presume. Another point B- is connected as usual to battery -ve. Will you pl clarify the single port can make is both for charging and discharging?
Yes it is possible to have a single port but that is not a very good bms as it only offers balance charging but no over current or low voltage protection.
Bro I have lots of 18650 batteries so I want to make a 20amps battery pack but in future I should be add more so can I use 40amps bms on my present battery pack, please reply?👍👍👍
Yes indeed you can do that for sure
aap achhasa gyan diya dhanyavad
Kya 17S bms ko 16S bms me badal sakte he kya🧐
Good and useful information thank you
Hello ! Your teaching is very good, I'm learning a lot. I want to know how can I connect an AC generator in the bms system to have an infinite system?
Thanks a lot.it means a lot to me...
Sorry to say but Thier is not anything such as an infinite energy system or free energy...
However if you want to connect an ac generator, connect it to the output terminals of the BMS of your battery pack where you connect your load terminals...
Bhai Maine bms 25amp ka use kiya hai vo bettery charge ke siris me ampere meter lagaya hai vo charge hote time kuch minute baat ampere meter 0 ho jata hai or short karne par vapas kuch minute charge hoga fir vahi step
Try using a different setup
Lithium battery ko cpu me lgane ke liye bms lgana chahiue
Gracias por la explicación, un saludo desde Madrid
Hello. Sir Aap Lithium solar Battery phosphate 12.8volt 150ah lske bare mein bataiye Thank u.
Bhai ola k bsm kese kam krta h bo btaye
There are two types of bms enhance and balance pls tell us about these
The balance one provides cell balancing while charging and discharging the other one doesn't
Superb
Brother,,,can i use laptop battery circuit as a BMS,,,for charging 18650 batteries and also Li po mobile batteries,,,,
Yes you can
@@DIYININDIA thanks bro
Hello! I need help to choose a BMS..I have a 14s 51.8v 23ah battery and a brushless sss 56104 790kv motor and an ESC 300 A from 3-16s and I would like to know how much voltage and how many amps I need. to buy BMS..Thanks
12 वोल्ट 7Ah के साथ bms लगा सकते हैं?
Is bms required for 3 parallel li ion cell??
That basically depends on the application for the parallel cell battery
Can we use it as UPS
12vat 8 ahm vali battery banani he to konsa BMS chahiye
Solar battery 12.8v /30AH ka bms repair kasay kare
Dear sir 48100T battery me over voltage ka alarm kiyu aata hai agr koi puche to kese btaye
one question
what is the meaning of load in ebike battery setup with BMS?
Does it mean the 2 cables that come out from the controller?
I know what is charging point but still confused with Load. Please t.
It refers to the total amount of powerdraw from the motor
Mera baitrry output voltages nhi bata raha hai
bhai mere pass 88 battery hai lithium 3.2 v ki main 4 battery series karke 12.8 v banta hai baki 4 battery ke 11 bank hai to bms ki jarurat hai 144 amp 12 v ban gaya inverter pe laga sakta hi direct
Get daly BMS from any hobby platform for cheap
Plz plZ sir Kya bms rc helicopter m use karna h plz reply as soon as possible plz plz
Yes for sure if your battery is multiple cell
Very good explanation. 👍👍
Thank you Friend
Bhai 24v bms ko normal 24v kay adapter say charge kar sak tay kay bolo?????????????????????
Yes
But kay hum 12 smps ko 24v bms say lagay to 6 lithium battery charge hoga ?????????
Bms ke badle main agar Lithium battery tp4056 module se charge kare to kya protection milega?
Tp4056 comes with a dw01 ic which may provide protection to individual cell but for a multiple cell battery a BMS is recommended which have a dw01 ic for each cell...
@@DIYININDIA give thanks for reply
main two lithium sell ek sath charge karta hoon tp4056 module se. es se koi problem to nahi hoga?
केसे पहेचाने की BMS कितनी अंपीयर का है और उसमें अधिकतम कितने सेल लगा सकते है
Datasheet of BMS
If that aint available then you need to reverse engineer the board itself
Sir motorcycle ka battery banae Hain Bms se to battery self Marne per Kam Nahin kr rhahai load nahi le raha hai
Could be the issue of the BMS
Please try without BMS
If it works Upgrade to a higher power BMS
Mere pas xyl30a hai kya iise lto battery charge ho ga bhaiya.
That can be checked in that ics datasheet itself
Will it require for drone
Its a compulsory thing for drones due to thier high current draw which causes cell imbalance
Nice information
Bhi ma 72volt 150ah ka ak battery banana chatahu isma konsa bms lagega?
Please answer me 🙏🙏
Thank you. I thought BMS was used for charging cells.
Bms does the monitoring to keep cells in safe operating region
Thank you very much
Sir BMS kitne se kitne Rs. tak mil jata hai, mere paas 22 Laptop sel hai mujhe aisa kuch banana hai ki ghar ke liye Lite aur Mobile bhi bhar sake Please Sir
what is the required bms for 14.4v 30ah lipo battery pack ?
Agr me 20 volt se isko charge krn to kia ye hr cell ko apne hisab se charg krega?
Yes
Thanku for useful information
can this BMS handle back EMF from DC brushed motor ? Why i am asking is i want to power a 12V DC motor for electric drill application.
Yes they are designed for such application
However a reverse protection diode is still recommend across the motor
My 17s battery pack is not charging above 69v
I have series 13s and 4s bms
There is a bit of unbalance in the cells about ± 0.05 volts
Also the bms cuts the power at only at 61 volts about 3.56 per cell
Please 🙏 tell me the reason so I can repair it
(About two times the positive and negative terminal also get short fow a few second with bms installed)
Please go through the BMS datasheet or contact the BMS manufacturer
Very good video
Hi.... I wanted 17s or 19s bms fpr lithium ion battery.... Pls reply where it is available
You can get it from elint India website
एक भी में चाहिए 48 volt ampere patient प्राइस कितना है
Nice
Sir over discharge kitni volt karti hai
Depending upon cell type
2.5v for LFP
3 to 3.2v for NMC cells
does it balance the temperature of the battery
Not really
Sir mujko 12v 4ah ke 5 battary ka set yani 60v 20ah ka battery charge ke le kitna watt ka solr chaheye
Bms कितने भी लगाकर चाज कर सकते हे। 12 के दो। bms लगाकर 24 लगाकर
How to check that the BMS LITHIUM ION battery charging module is working or not
By hooking it up to a multimeter and testing its cutoffs and cell balancing
I like your video
Can i exchange lithium ion batteries (with BMS) from ups battery ?
Yes you can theoretically do that for sure
@@DIYININDIA ok fine... i try.
Brother, I have around 20 no's lithium ion batteries of cordless drill machine's having voltage 3.7 each and 1500mah i want to make battery for bike so please suggest me how can I make a 12 volts battery or if it requires a BMS circuit board then please suggest type.
Thank you.
Use a 3 s bms and make a 3s battery pack and assemble rest in parallel
Hi got bms which is having b- p- and pc- terminal.. Can you pl tell what is pc- terminal is for..
but super explaination
Please guide me my motercycle pulser 150cc self start ke liye lithium battery pack kaise banaye kitni battery lagani chahiye
You need a high discharge lithium battery pack
Sir kitni battery lagani chahiye
Vai 6 lithium ion battery k liye konsa bms lagega pls bolo
India
Which programing language is used in BMS
C
Kya Sir BMS par 5A Horn Chala Sakte Hain Is Par Video banaye Zald se Zald
Mujhe Bms14s48volt chahiye adras bataye thenkue
Wonderful
Vai video accha tha. Par kafi technical chize skip kar diye ho
Namaste. I need to build a 18volt power pack for a cordless drill. What type of bms do I need. Thanks.
Dwo1 ic based balance charging
लिथियम सेल 12 हो तो उस पर कितने 3s या 4s बीएमएस बोर्ड चाहिए
BMS KI BARE ME OR JANKARI DO.....OR HI-Ah LITHIUM cells ki bhi video banao...or good quality battery kaha se Liya Jaye. 3.7volt--100ah kaha milega..thanks👌👍
For more information about bms check the video description links,will be making more videos on the topic soon,for a good quality battery contact sellers on indiamart and conduct load capacity test on the sample cells...
14S 48V 30AH BMS LINK DIJIYE
Sir mere pass ek bms 3s bird hai Mai ye janna chahata hu ki agar bord me Mai input point par 12 volt deta hu to bord ke
b- point se b1 par volt Kay hoga
B- se b2 par volt Kya hoga
B- se b2 par volt Kya hoga
Bina battery pack jode
Bas test karna cahta hu ke Mera BMS circuit board theek hai ya nahi
0v at - ,4.2v at b1 ,8.4 at b2 and 12.6 at +
Pc ups me pawer back ka 12 battery 4-4-4 ke हिसाब se lgaya hai kiya usme bms lgana chahiye
Yep
Bhai mai 9 sell se 12v battery banaya hu battery3.7 volt 3+3+3=11.1 v battery me kaunsa bms lagau plzzz reply bro 2600 mh ki battery hai
3s bms
Bhai Kya Baat He Bohot Time Se Apka Koi VDO Nahi Aya He
Shayad Apki Padhai Chal Rahi He Isliye
12v ke liye BMS jaruri ha kya lagana