Why remove all that stuff? Watch the magnetron replacement video - take it out and the thermal fuse is on it. Much easier than disconnecting all the blower stuff! By the way, how about testing the fuse before you assume that is the issue? Just sayin'
Hello we have an LG Microwave. Our microwave turns on when we press start to heat something example if we click one minute then in a few seconds the light turns off and not heating but timer on display is still going any suggestion? Can it be the the Magnetron Thermal Fuse?
My microwave aint heating i changed all the door switches an the little black diode connecting to the capacitor an to a ground i dont know if its the magnetron r the transformer any ideas
What is the symptom when the thermal fuse is failing ? I have a microwave heating up food at 50% speed as usual. Is the problem on the Magnetron or the fuse ? or maybe the capacitor ?
We recommend using the repair help section of our website at: www.repairclinic.com/repairhelp?TLSID=1773 Using your model number will give you the most useful information.
congtusacto Disconnect the power cord and remove the top grille and control panel and you should be able to gain access to the fuse. That is a good place to start. www.repairclinic.com/RepairHelp/Microwave-Repair-Help?TLSID=1773
i have a ge that would start then stop and display PF. i tried unplugging and plugging it back up and now it wouldn't turn on unless i hit the side of it.
So how do I know if its the thermal sensor gone bad? Mine keeps popping fuses. When I place amuse the light fan clock all works. Heat water fuse pops. It may have been used to cook a potato and overheated
If the thermal fuse is bad it will not normally blow the fuse when the magnetron comes on. If the magnetron itself is shorted or the high voltage capacitor is shorted, it can blow a fuse when heating. These things can be checked with a meter but we recommend you have a qualified service person look at them for safety reasons.
It's funny at this day and age you're still using regular screwdriver instead of a power pocket drill that speeds up the assembly/disassembly time by three times.
+surapong sivi There is likely a separate fuse for the control panel, my GE had one. It was located right above the control panel under the cover. $1.50 from RadioShack.
Nice video but manufacturer should be ashamed they made it this damn tough to replace a fuse!!
Why remove all that stuff? Watch the magnetron replacement video - take it out and the thermal fuse is on it. Much easier than disconnecting all the blower stuff! By the way, how about testing the fuse before you assume that is the issue? Just sayin'
ge microwave jvm3160rf2ss stopped working altogether. How do I know if it’s the fuse in this video or the ones that look similar behind control panel
Nice video, some things can really be a pain in the backside to test / replace.
Hello we have an LG Microwave. Our microwave turns on when we press start to heat something example if we click one minute then in a few seconds the light turns off and not heating but timer on display is still going any suggestion? Can it be the the Magnetron Thermal Fuse?
My microwave aint heating i changed all the door switches an the little black diode connecting to the capacitor an to a ground i dont know if its the magnetron r the transformer any ideas
thanks for this video its helps.
What is the symptom when the thermal fuse is failing ?
I have a microwave heating up food at 50% speed as usual.
Is the problem on the Magnetron or the fuse ? or maybe the capacitor ?
We recommend using the repair help section of our website at: www.repairclinic.com/repairhelp?TLSID=1773
Using your model number will give you the most useful information.
thanks for the video. my GE XL1800 went out, no lights, power etc... Where can i find the fuse or where do i start? thanks
congtusacto Disconnect the power cord and remove the top grille and control panel and you should be able to gain access to the fuse. That is a good place to start. www.repairclinic.com/RepairHelp/Microwave-Repair-Help?TLSID=1773
my microwave only runs 3 seconds then turns off, any hints on whats wrong?
No post R&R, uninstalled test? Just going to trust in the Force?
i have a ge that would start then stop and display PF. i tried unplugging and plugging it back up and now it wouldn't turn on unless i hit the side of it.
So how do I know if its the thermal sensor gone bad? Mine keeps popping fuses. When I place amuse the light fan clock all works. Heat water fuse pops. It may have been used to cook a potato and overheated
If the thermal fuse is bad it will not normally blow the fuse when the magnetron comes on. If the magnetron itself is shorted or the high voltage capacitor is shorted, it can blow a fuse when heating. These things can be checked with a meter but we recommend you have a qualified service person look at them for safety reasons.
where is the fuse on the model number JES1142WD03
I have about 4-5 thermals
It's funny at this day and age you're still using regular screwdriver instead of a power pocket drill that speeds up the assembly/disassembly time by three times.
We do that to make sure we don't lose anyone. Not everyone has a drill.
GE designers solder in the green wire. Now I have to buy a soldering iron to remove it! I will try my big propane torch first!
Porq el vetilador no se apaga
Key pad control not work
You'll find our website's free troubleshooting and repair help system to be helpful: www.repairclinic.com/repairhelp?TLSID=1773.
+surapong sivi There is likely a separate fuse for the control panel, my GE had one. It was located right above the control panel under the cover. $1.50 from RadioShack.
Thank U