Edgebanding curved Corners by Hand
HTML-код
- Опубликовано: 12 сен 2024
- In this short video tutorial I will share my trade secrets on how to edgeband your manufactured board products where you have curved corners. This can be quite tricky to achieve nice clean and tight joints between your PVC edging and the edges of your board. With a few simple but effective steps you too can get perfect professional results.
Video Links:
EDGE MELAMINE | The Best 3 Ways to Edge & Trim Your Board At Home!
• EDGE MELAMINE | The Be...
How To Edgeband & Trim Melamine | Edging Melamine Board | How To Apply Edgebanding Pro Tips
• How To Edgeband & Trim...
Affiliate Links:
End Trimming Tool:
amzn.to/3JZ5bOz
Chamfer Tool:
amzn.to/3RCpUJM
Planner Blade:
amzn.to/3HrYktW
Vacuum Pump (NOTE: NOT THE SAME PUMP AS I PURCHASED BUT SIMILAR! - check the pump has your countries power-point plug):
amzn.to/495AeSy
Pneumatic Foot Pedal:
amzn.to/3HCUyxL
High Strength Spray Adhesive:
amzn.to/41xcRgr
Contact Adhesive:
amzn.to/3KLeTmq
Heat Gun:
amzn.to/3IS9f21
Flush Trim Router Bit Set:
amzn.to/3mDtoAE
Recording Equipment (Please note I am NOT Sponsored by these brands in any way):
Rode Wireless Go II:
amzn.to/3IYGKOK
Rode Lavalier Go Professional Mic:
amzn.to/3J2ITcq
Sony ZV-E10 Digital Camera & Vlogger Kit:
amzn.to/3AEGsJm
I really like the use of the edge planer blade for trimming. I've never seen that done before. Seems like the perfect way to do it after watching you do it. Your skill in placing the blade to trim the banding is notably experienced. Well done, and thanks for the tutorial. Happy to subscribe.
Thanks for watching and your support 👍
Wow, it turned out pretty good but then again everything you do turns out good and neatly done! Good vidio
Thanks so much for your support Antoinette 😁
@@geoffsjoinery4990, You're welcome keep up the good work I enjoy watching you 🥰
Hi Geoff; great video as always, greetings from the UK. Is there any chance of some more cabinet building guides? I have learnt so much from you're channel, anything on bedroom furniture would be of great interest. Thanks again.
Thanks for the great feedback, have you watched my two videos on the bedside tables? Also there is a built in wardrobe but I do need to get around to showing some basic kitchen style cabinets.
Thanks for watching 😁
i can guestimate but wondering if you could say the min radius this will work well for ? what you have tested.
Thanks for sharing your knowledge. I wonder if such 90 degree curved angles can be covered with 2 or 3 mm veneer? Or it's too thick?
It will be a similar process using a heat gun to soften the edging and making it pliable. Thanks for watching
@@geoffsjoinery4990 will this method work as well for beveled edge (bending along the grain contrary to opposite to the grain which is shown in the video)?
Yes of course you may need to get a wider edge tape to compensate for the bevel.@@olegx.8173
Hello, which Filter do you use on your vakkuum pump ? - searching for a suitable one.
Hi there, I simply just use a small automotive type inline fuel filter to capture the dust, I have left an Amazon link:
amzn.to/3reWhVu
Thanks for watching and good luck:)
@@geoffsjoinery4990 very friendly - Thank you
This kind of work efficiency is too slow. Now there are curve edge banding machines on the market. A plate can be finished in three seconds. Why not choose curve edge banding machines and edge trimming machines?
Yes of course there are machines for this but as the title says "Edgebanding Curved Corners by Hand". Not everyone can afford a machine to do this or it may just be a one off job. The purpose of this video is to demonstrate "how it can be done by hand"!