The Emergency Repaired of Broken Steering Box Rocker Shaft // Its Made Better Than New...
HTML-код
- Опубликовано: 28 сен 2024
- The Emergency Repaired of Broken Steering Box Rocker Shaft // Its Made Better Than New...
#brokensteeringboxrockershaft
#emergencyrepaired
#madebetterthannew
#pkprocess
Lesson learned from this video. You have two scrap pieces. You can weld them and create a bigger scrap piece.
Ha ha love it anyway its not important its only steering its not like it might kill someone
Pakistani men very creative n innovative in repairing and rebuild vehicle parts..
I confess that in more than 30 years in the field of mechanics and auto parts, I had never seen a steering gear break like this, normally there is wear and tear on gears, bearings and bushings.
A clean shop? Bravoooo.
Cut a pilot hole first on the flat first and you won't have to hold your drill bit and tighten your drill bit
Parabéns pelo seu conhecimento meu amigo
The weld may be satisfactory for the amount of torque and vehicle used. Or at least last until a new part is available. Aircraft parts that have weld repair are ultrasound/x-rayed.
Excelente trabajo los felicito 👍 👏 😉
Cuatro detalles que no aprecié:
1) Se omitió precalentar la pieza antes de soldar.
2) Viendo todo el procedimiento, me temo que no se ha usado un electrodo adecuado para ese tipo de acero.
3) En una reparación como la que nos ocupa, se debe crear una "Garganta" amplia para que la soldadura parta desde el centro mismo de la pieza en lugar de ser superficial como en este caso; el núcleo que se dejó para empotrar con la prensa hidráulica, sirve solo para centrar pero no aguantará ningún esfuerzo de trabajo.
4) Después de la soldadura, se debería dejar enfriar lentamente (en un recipiente con abundante cal en polvo por ejemplo) para evitar la cristalización del material.
No te preocupes amigo el trabajo no es para ti deja en paz a los demás no seas entrometido.. estas personas trabajan para vivir y lo hacen muy bien…
How can it ever be "better than new"? Look closely at the welding. There is very little "penetration", the root weld is hollow with lots of slag left behind and the actual welding technique leaves a lot to be desired. There is no way that this will even be anything near as strong as when it was first made.
Ohhh you picky I like to check your jobs.
@@jesus2391 All of my "Welding Jobs" are 100% x ray inspected or where that is not possible then NDI inspected after each and every "run".
But there again I am a proper welder with 40+ years experience on welding high pressure systems
Учебное пособие, как не нужно делать)))
When I always see that the turning tool is not aligned in the middle!!🤨😵💫
Considering the potential risk to absolutely everyone who ever comes with in 100 yards of this vehicle on the road, I would say going the cheap route and saving the 400 or 500 Rupee (Less than 2 dollars) over buying a new Gear. The owner of this vehicle and the shop that performed the work are complete Morons. Stupidity at this level should be criminal... Oh wait it is Criminal in most developed countries.
This steering box appears to be from a heavy vehicle, ie semi tractor. It probably was broken during a wreck so normal loading would never break it. The logic here is probably that it would never stress the repair during normal driving. However….. stress on the DRIVER or passenger or anyone knowing of this repair would be enough to avoid this vehicle forever.
RIP truck driver
Я так понял у них нет слова нельзя, всё можно сварить и расточить😀
I knew it was going bad when I saw him clamp that ceiling area in the vice
It's called a vise, dufus.
@@Jeff82556 Depends where you’re from! “Vice” in UK. You missed “ceiling” 🤣
The Showcasing Remarkable Mechanical Skills
Меня одного смутил тот факт, что поршень-рейка уже отсутствовал? Тогда как крышка вала сошки была затянута на все болты. Но ведь чтоб вынуть поршень рейку, нужно вынуть вал сошки!!! НАХРЕНА затягивать болты, при том все ??? !!! Ах да, нам же должны показать экшен, претендующий на конкуренцию с голивудом! 😂
will not last long since the original broke under preddure made one piece , how long will this welded one last ??
Hard to say, maybe it was welded before....
Nonsense repairs! They do all these "repairs" for the purpose of making youtube videos. You will never see these parts ever work again.
which may well be better - for everyone involved
Проще и быстрее было изготовить новую деталь, чем ремонтировать эту, при том, что ремонт этот бестолковый.
Good work 👍
I'm proud of you all..
It will work, giving time to order a new part.
Probably welded 10 times already....😂
Вот сколько смотрю - ни один балбес не подкидывает массу к заготовке. И действительно, а нахуя?
Надеюсь вы умеете также сваривать кости и позвоночник раз решились сварить вал сошки рулевого редуктора
Giỏi quá a thợ tiện
What on earth was supposed to have happened to that steering box rocker shaft to cause it to break the way it did.
Surely the splines would have been chewed off first.
Might have been welded before....
Drifting the truck.....
Hit a pothole at high speeds maybe?
These guys do these repairs because a new part is probably not available and a new vehicle is more than can be afforded. It looks like a lot of the stuff they have is very second hand.
Unexpected random loss of steering at some random point in the future right there, You never repair parts like that, they can not be trusted to be safe.
Super jest to wykonane pozdrawiam serdecznie 👍👍👍👍
jaja se robisz?
Рулевой механизм
Ở xứ sở này, phụ tùng thay mới là cái gì đó vô cùng xa xỉ và không có trong tự điển của họ.👍🏻👍🏻👍🏻
I'll bet when that broke, it scared the shit out of the driver.
Thẳng tuyệt đối không ?
ويكان جدتي رحمها الله هي من صنعتها
اخخخخخخ😢😢😢😢😢🎉
👍👍👍👍👍
Максимально всратый "ремонт". До следующего перекрестка не хватит.
Полностью согласен. Привет из Уругвая.
Totalmente de acuerdo. Saludos desde Uruguay.
Dios mio porque son así con sus semejantes solo critican me gustaría criticar tus trabajos,solo tú eres un genio ay ay ay.
@@jesus2391 Me equivoco? Por qué debería colmarme de elogios cuando veo gente haciendo estupideces?
How could you grip the sector thread on a vise you ruined those threads,and don’t you people have Crazy Glue at your Local 7-11?
It’s cheaper to use crazy glue
good job!
Have you ever done any structural steel fabrication?
Would you trust your life on this not breaking again?
I think the answer to both questions is a resounding NO.
Devia ter dado apenas uma solda e vai dar duas, alem de deixar a peça mais fraca.
Nonsense 😂😂😂
Nice 👍
ليس جيدة 😢😢😢😢😢
come on you downers didnt it say its better than new?
These parts do not last. I a country of no money you do what you have to even if it kills a bus load of people.
Poor repair decision. The repair weaker than the original hitch broke. Threader inserts would be better in my opinion.😊
Only you can do jobs the rest of us is not good….
с гамна и палок слепили гамно
Подобное я смотрю с одной целью: увидеть, как нельзя делать! (I watch things like this for one purpose: to see what not to do!)
The good thing is you know exactly where it’s going to break. Again.
I commend you guys for a nice clean orderly shop!
I wouldn't let these guys work on my enemies vehicle
I hope they don’t work on airplanes !
Did you know that 75% of pilots in india dont have pilots licences so it wont matter if they did a bad repair just blame it on the pilot when it fails
они сопромат и технологию металлов видимо не учили... только идиот на сварку будет соединять...
Just because it looks pretty at the end doesn't mean its reliable, durable part
Your root weldig is scrap metal.
1/2 the strength of the one that broke. The welding did not go %100 deep
Pouco penetração de solda, a qualidade deixou a desejar.
Сваривать лучше нержавеющим электродом (зелёным)🤔
Why? The welding rod should match the material to be welded and these people invariably use the very cheap PaK Bridge (6013 type) welding rods which are not optimised for welding cast steel.
Гнутым желательно
This is a safety part....such repair is not allowed....high risk of failure during work causing fatal victims
disaster
Das wär in Deutschland unmöglich
Stimmt. Nie gesehen im deutschen Stuff.
Nice 👍👍
Гарантия до ворот после сварки метал слабеет и шлицы сотрутса за пару недель.
Не успеют стереться, она сломается быстрее)) если они умудрились вал рулевого редуктора такой толщины сломать.
Very master!!!!😜👏👏👏👍👍👍👋👋🇮🇹
When you buy Chinese crap...
I don't know if you're English or American, but there is a factor called "material fatigue" that can occur from misuse or overuse.
I have repaired many "Leyland" brand bus axle tips (Made in ENGLAND) and they broke not necessarily because they were Chinese but for the reasons I explained above.
I think the only trash we can talk about here is your arrogance.
@@Fernando-dv2ogYou got my "like" for the respect not content reasons, though.
I never ever faced such an issue with German , US or British (Sheffield) made ones . As for my alleged "arrogance", I bought a graphics tablet of CHINESE manufacture. I've been so far an "orthodoxically" user of several tablets of a well-known American company that earned a monopoly position in the market for many years - which was honestly deserved for its quality and reliability. The Chinese tablet, to my absolute surprise, turned out to be of the same quality and durability of workmanship yet having better and more numerous features - but with the price ratio 1:5 in favor of the Chinese.
Is this really how " biased, arrogant nitwit" behaves as you suggesting?
Best regards.