Raptor 660 starter clutch Removal/Install Pt. 2
HTML-код
- Опубликовано: 11 окт 2024
- In part 2 I go over the visual diffrence in 01-03 and 04-05 Raptor starter clutch. I install the starter clutch and do some cleaning prep for new starter clutch. Starter clutch is about a 2 hour job from removal to full assembly with all correct tools on hand and Parts.
There is always haters when making a video. I love when someone fixes their own. We learn from our mistakes. And if we don't make mistakes we are not learning. Yes there is specs,not everyone has the proper tools. I would give you 2 thumbs up just for the effort. A lot of people just want to see how hard something is knowing that they will never do it themselves but try to talk down the person that is. I think you did good you did it yourself.
Thank you. Can't make everyone happy. But you should know I have not had one issue with it. Running great. Again thank you for you courteous reply.
MoneyPit Garage very good keep up the good work
Wish you could find tutorials like this for all parts relating to raptors. It’s always a learning experience because I have to do things without knowing what to do! For example I cracked my starter cover in half the first time when replacing my stator. Lol, great tutorial my man!
Thanks man!
Can put the link for the part please please 🙏🏾💯💯💯
Good video, I know it's a few years old. NEVER oil the tapered shaft or the inside of the tapered flywheel where the woodruff key goes - that needs to be a dry fit or use loc-tite. Torque wrench!!! Almost everyone can relate to this video, especially if you work on your own toys.
Rob Cure getting ready to put mine back together. What all needs to be oiled up?
so when he oiled up that shaft, pretty much dont do that ? lol
It’s a one way bearing replacement and it’s attached behind flywheel not clutch. Clutch is on other side!! Great job on replacement I’ve seen peeps really struggle doing this
That's the starter clutch.
Only use an impact to loosen not tighten.The only thing that needed loctite was the flywheel nut. But not a bad job. My raptor would crank but wouldn't fire, I found a blown 20 amp fuse on the solenoid, replaced it and haven't had a problem since.
Scott Bowers I found that out the hard way. Cracked the smaller cover reinstalling it with a impact.
I cringed so hard when you where using the impact driver on the side cases. You don't tighten them like wheel lug nuts lol. You use a ratchet and torque wrench by hand. Or else next person that pulls it apart is gonna have aluminum threads on all the bolts you over-tightened
I was about to say yea you got to torque them at around 100 some pounds I know that gun didn’t do that😂
I’m not hating on him but tht was one thing tht he did wrong. Gun probably only did like 50 pounds or so. But it was a good tutorial
Ya they are only 7.5ft lb. I’m currently fixing 4 threads that the previous owner of mine jacked
@@IluvMikel100 pounds for the cover?! You crazy?!!!
I broke that bolt stator bold not with 1/2 inch impact 😂
When I did this I numbered each bolt and location with a sharpie to make sure everything went back where it came from
I feel sorry for who ever needs to remove the side casing next. All that damn lock light and impacting
I paused the video at 11:37. That pin dowel I'm missing. What's the purpose of it? Do I really need it?
Looks like all it does is help hold the gasket in place
Does need oil in the case after you did the job ?
No, It gets oil in that area from crankcase
How come u didn’t use the big gear behind the one way bearing u took off? Does it actually even need the new gear or just the bearing?
I need help. Between the cover and starter motor is there a O-Ring?
Be careful not to break the cover.. its only magnesium and impact drill strong enough
Hey bud where did you get the whole kit from?
I'm in the process of replacing mine RN but I can't get that one way barring nut off
Im changing my one way bearing but I discovered that the fly wheel Nut Is welded I bought it a few weeks ago and when I open it was line that like WTF Does that weld a fly wheel nut Really ???? Lol
i cannot believe i just witnessed someone tighten down 8mm bolts with a damn impact and didnt break or strip any. you sir are one lucky son of a bitch not to have any problems there
Bean Shooter skill, lol.
Do I really need to put loctite on the cover bolts? Is it recommended?
Where does the negative wire on the upper right hand side go? I can't figure out where it goes and you don't put it on anything in your video. My starter isn't working and I think that's the reason why it just clicks. Any help would be appreciated
Are you sure it's the starter clicking and not the relay under the seat?
It just bolts in with one of the stator side cover bolts
Did the starter clutch keep it form working let me no please
Is it normal to have oil in that side of motor
Was that carb cleaner that you used to clean it off?
What brand parts did you use?
I installed a new one way in my 2008 raptor 250 and I’m still having issues with it starting ? It does the same as before, the starter turns but nothing happens 🤷♂️battery is good and starter is good
Have you confirmed the bendix is shooting out?
SCBB MEDIA thanks for the info and I took it apart and looked at my starter and hit the ignition and what I see is my starter is spinning the wrong way . Could that happen ?
Is the big gear in the back supposed to move forward and backwards a little? I just installed mine and that gears moves in and out. When removing didnt pay attention if it did that initially
2 years late but for y'all reading these comments in the future. That big gear shouldn't have much play at all, there should be a washer between it and the more inner side of the shaft. I didn't replace that washer and I learned quick when I started it that something wasn't right. (Loud grinding sound) The bigger gear was making contact with the smaller one and that play pushed it over and had it skipping around in there damaged the edges of both gears. They do a lot better with that small washer in place.
Have you gotten rid of the 05 clutch? If not I will pay you to have it shipped to me. I’ve been researching and cannot find an 05 one way for my raptor.
Ebay
Where did u bolt your black wire to ?
Do I need that clutch bearing puller, remove it? is there something ican substitute with?
I would recommend proper tool. I think it's only about $30 in eBay.
Can a dr650se starting clutch work on a 1000 Suzuki
Where does that wire go that is hanging there I think it's a ground
toeder420 can you give me a time so I can check?
Sweet thank you. I'm almost finished video helped a lot. I can take a pic and shoot you a text of the picture
+toeder420 can you give me a specific time?
I think he's talking about the black wire, time 10:50. Great video by the way. Thanks
toeder420 yes sir if it's the one 'dangling" it's a. Ground to the case
But you didn't connect the ground wire
When doing this does it mess with the timing at all?
No
What brand starter clutch you use
I am unsure. I do know that I ordered it off ebay. I have had no issues. Still own the atv.
@@markchapman8101 was it the ideal brand? I don’t wanna get shitty parts of yours is working for you is really appreciate it if you check. Should be in your history on eBay purchases if you do t remember
Where did you get your parts?
Ebay
Link the part please
I need to do mine. Where did you buy the kit and what is the kit called??? Thanks in advance.
Ebay! Starter clutch tool.
Good Job! But,....kind of dangerous way to tighten them with powertool..., you should find out correct torque for all the bolts, you easily drip/ overtighten them!!! Just saying.......
Eero Laukkanen defiently should have as I have a PDF manual on my phone but I didn't and I believe I recommended doing it the correct way. But I have had no issues with this four wheeler run perfect and my son loves it.
Lucky you,...those engine blocks are aluminum, so be careful =)
Eero Laukkanen What I don’t understand why he didn’t start the bike to show us that everything was intact. If you’re going to start a project such as video recording the project why not show us the fun part it’s starting up with no issues?
Jay33 Ford yeah that pissed me off I was waiting for him to do it so I know everything still works and I don’t screw up my bike because if I do I am going to be pissed!!!!!!!!
Will that fit my 250cc ?
Does anyone know the torque on the bolts?
Holy christ man, where is the torque wrench.. this was painful to watch
Bike still runs strong though.
impact on aluminum makes me cringe hard
people need to chill on the case bolts