As a General Electric Company Field Engineer, I installed many turbine rotors like this one. Usually I put them in a little slower.... I'm certainly glad these guys emptied their pockets before getting near the open casing.
You wouldn't happen to know the old guy who worked on the sl-7 ships awhile back? I worked with him on a couple of ships back in the early 2000's,he must have been in his early 70's back then...Nothing he didn't know about steam ships. Could be an ornery old bastard though.lol.didnt much care for black folks. cant remember his name only that he was a GE rep.
I know, I cringed sooo hard when I saw him do that. Imagine getting impaled by houndreds of compressorblades and then crushed by the whole shaft assembly.
I have worked around cranes for 36 years. Driven them about 12.I have never seen one fail that way.Generally people working beneath cranes seem to think they have nine lives.
"Psh... why order a fancy lift system for tens of thousands of dollars when I can get what's basically the exact same thing for only $599.99 at 'Harbor Freight.' I mean come on, no one will know the difference anyways!"
Yikes! The blade damage is dramatic, but really, the whole thing is junk now: all blades, disks, the shaft, the stators, the bearings. They're now back way farther than when they first started the overhaul. At colossal expense, for sure.
Lol Will, the stator is the name of the part that goes in between the turbine blade sections in order to prevent the gas from rotating as it flows through the turbine, and the bearings are clearly visible in this video…
Out of all the crane accidents I've seen in videos or read about, this is the first where a winch failed. It's usually a cable or some part of the actual rigging that fails. Either way somebody is out a chunk of money even if nobody gets hurt. Glad nobody was hurt in this one.
no body will go under load in any way...that guy was also doing the same to check installation...safety guys never allow to stand under even when one blade is being installed that was a whole set of Compressor and turbine with rotor...
Yup - love to know more about this one. So sad, seeing finely constructed hardware destroyed by cheap shit castings in the crane. I'm guessing that was some sort of transmission shaft with busted off engagement dogs. It explains that mechanical scream just before it came ALL the way loose. No excuse for not using forged components in that drive train.
"Uh, yeah... I just pissed myself... Over." "That's a big 10-4. So did I. Over." Christ those two guys down in the area close to where that turbine is mounted were very luck to have been able to clock themselves out that day!
I used to work for GE as a project specialist, One of the engineers gave me a copy of this 3 years ago.... This was in a plant in Germany... I remember this. thanks for posting it...
+bonjourmssr Yes its salvageable but very expensive, and it will cost 1-2 years. The rotor is too damaged. 180 degree on the underside, and in the upper center from the traverse impact. Even the underside of the housing, wont look well. Mostly there will be replacement from another powerplant, which has gone offline. If there are more turbines of the same type in one plant, there is often a replacement rotor in stock.
This poor Crain Operator most likely received a lot of "Atta-Boy's" & pats on his back for the many good lifts in the past. But it only takes one "O-Shit" to wipe all them Atta-Boy's all out and lose your job.
Worked on many a steam and gas turbine rotor swap as a millwright with no problems, that rotor would weigh less than the cover which was removed first, the crane would be rated to handle the cover weight, it appears the hoist coupling failed.
Yeah looked like they had it rigged right. Spreader beam and plenty big enough straps. I have been involved in many rigging evolutions and you can get complacent sometimes.i worked in the shipyard and sometimes because of space constraints you HAD to get under the load in order to land it. or refuse and lose your job.
I’ve done every part of this procedure many times, mostly as the crane operator, the notorious weak link of those crane’s were the load brake being not adjusted right, that one was having trouble holding the load, you can hear the motor over rev, this can cause multiple things to fail, usually the gearbox or coupling. They dropped the stator at my plant after I retired and killed a boy on the turbin deck.
Wow, thanks for the inside info with the load brake. I'm gonna say that you are spot on with your diagnosis. I'm assuming this isn't stateside so no OSHA report to read. Again, thanks. - Surry Virginia
Kousheng nuclear power plant in Taiwan has an old turbine rotor on display at their entrance, sitting out in the rain, of all places. I wonder just how long it took to decon that thing to free release it, considering it's a BWR plant, and the turbines run on primary steam. :-o
Luckily, it seems that no people were injured in this accident. That's a very positive piece of information. Yes, the turbine is completely destroyed (since it cannot be balanced properly again, no matter how carefully it is repaired), but it's just a block of metal. A value of $6.5 million can be produced pretty quickly by a small team of people, but there is no monetary value that could compensate for human health or life.
+semmtexx thats a "fenner"coupling- used in the EU -fenner taperlocks adapt the coupling to the shaft--seen these in screening plants--when one looked like this on a plant, someone took a maul to it,because they forgot to loosen the 2 allen head screws around the taperlock to close the gap between the coupling halves.
The crane operator must've been so relieved when it became clear that the failure occurred because of the actual crane breaking, rather than his negligence
I saw a replacement gas turbine on its stands waiting to be put in at a Nuclear Power plant around ten years ago. It didn't look to be real heavy. Not over 50000 lbs. A crane like the one that failed must have gotten their parts cheap or it wouldn't have failed. I'm sure it was rated well over what ever it weighed. But then a worker removing the cover of the turbine being replaced was throwing/flipping a wrench in the air while standing on the cover. This was in PA so who knows.
+A.H. Shukry IMO, lack of daily inspections especially before heavy lifts like this---looks like the bearings at the input shaft of the gearbox failed, causing the shaft to load sideways under load, when the fenner coupling failed the input shaft broke thru the brake band asmby., causing the gearbox to freewheel, dumping the load, but thats my 25 cent review of this--mgt. saved a dollar, but they f%$#@ed themselves here!!!
janj0n whups!, ya let the bean counters do the talking, save a few bucks!, are you sure that part needs replaced?, this part is the new, and improved version!, it'll work much better.
Don't worry Jim....the maximum load rating is a guideline...these things can handle twice the recommended max...OH HOLY SHIT!!!! What do we do Jim? Jim??? JIM???? where are you running Jim????
Stress point- where forged hardened steel should have been used instead of cast on that particular component? I do not know, just saying. Thank you for the excellent video. It is definitely a learning experience for all, and I am glad no one was hurt.
Go pee in the cup... Seriously though, it sounds to me like the winch broke. you can hear gears screaming and stripping right before the earth-shattering KABOOM!
Viewed it again and you're correct. I was still thinking about the accident when I typed that. That fellow in the yellow hard hat doesn't know how lucky he is to be alive. What failed?
i work on gas and steam turbines for a living and this is a gasser. you could say this is the quick way of setting the rotor.the rotor itself is around 15mil let alone the other damage to the turbine itself.
+Jochum Bakker No way, this is not GE machine. It's not a Gas Turbine at all so Frame 9 shouldn't be mentioned in first place, it's a steam turbine and rarely this type of turbine is used in power plant because of its inefficiency.
That should serve as an explanation why you never ever stand under a suspended load. Like the guy to the left did shortly before it came crashing down. At least it looked like he was under it.
That turbine rotor had to weigh at least 50 tons. When that rotor fell everyone in the power plant must have felt the floor jump under them and heard the sound of the crash.
Nomeclature Issue: STEAM TURBINE is a device that extracts thermal energy from pressurized steam and uses it to do mechanical work on a rotating output shaft. GAS TURBINE, also called a combustion turbine, is a type of internal combustion engine. It has an upstream rotating compressor coupled to a downstream turbine, and a combustion chamber in-between.
Thanks to God no one was hurt, there was one technician very near the incidnet. The Turbine rotor is badly damaged. It seems either the safe working load of the overhead crane was close to the turbine rotor weight or the overhead crane was not inspected and certified for such critical heavy lift for long time.
Who has been doing the Crane inspections? Also when we did a heavy lift at the Power Plant on a Steam Rotor fitting in place and I was the Crane Operator when I worked there during one of our turnarounds. There was eyes on everything and QUIET during the lift. Wow very expensive. Thank god no one was killed.
+kc5hgv I was wondering why there was so much noise and normal day to day sounds going on during that lift. I even said out loud to the screen....Yo shut the fuck up....we are moving something heavy here... Everyone needs their ears on and eyes open at this moment.
+SquillyMon +SquillyMon Almost seems like they didn't have a foreman there at all. Just a bunch of grunts told to get it done with no former experience doing so.
+CafeBikeGirl Or you should, a good reminder to get your equipment inspected and tested by competent test companys and to never stand under a load. Nothing like a good graphic example to get safety messages across.
One of the blades of the turbine was bent in the mishap. A worker was able to take a ballpen hammer and tap out the metal. The turbine was up and running after only a minute and twenty-two seconds after occurrence.
As a General Electric Company Field Engineer, I installed many turbine rotors like this one. Usually I put them in a little slower.... I'm certainly glad these guys emptied their pockets before getting near the open casing.
You wouldn't happen to know the old guy who worked on the sl-7 ships awhile back? I worked with him on a couple of ships back in the early 2000's,he must have been in his early 70's back then...Nothing he didn't know about steam ships. Could be an ornery old bastard though.lol.didnt much care for black folks. cant remember his name only that he was a GE rep.
People in charge '' Oh, look at the time, Im off to Mexico!''
This aged well lol
at least they dropped it I the right spot
yeah.. ye know the bends and stuff thats fine itll work.
02:33 thank you sir.
Close enough! Lol
@@jakelencher817 only wobbles a little looks legit as they say and give a thumbs up
😂 fucking nailed it. Hate to see something like this, but the signal guy was on point.
!!! at 2:25 . Never never never walk under a load !
Some put way too much trust in machinery, if it's made by a man it will wear out tear up fail break, size means nothing
yeah he was kinda scaring me there
if he decided to do that a couple seconds later then he would be dead
I know, I cringed sooo hard when I saw him do that. Imagine getting impaled by houndreds of compressorblades and then crushed by the whole shaft assembly.
@@tinyjudoka6024 you mean turbine blades, correct?
I have worked around cranes for 36 years. Driven them about 12.I have never seen one fail that way.Generally people working beneath cranes seem to think they have nine lives.
Why would it fail if it was rated to carry that load? would it be a maintenance issue? or was it most likely exceeding it's load limit?
@jackthecat6225 in this video or in general?
@@jackthecat6225It wasn't, I read the crane was rated for 60 tons and the turbine was 75 or so
"Like a glove!"
Utterly painful to watch.
I find mans folly quite amusing.Should have been a fail safe crane system.Oh well,live & learn.Atleast there was no loss of life..
"Psh... why order a fancy lift system for tens of thousands of dollars when I can get what's basically the exact same thing for only $599.99 at 'Harbor Freight.' I mean come on, no one will know the difference anyways!"
Especially when it's carrying stuff 100 times its own value :D
@@ejnaygfantzcg That's over 10,000 times its value if you could get such a lift at Harbor freight for $600
I just started working in this business and man, this drives home one very important lesson: stay out from under the load!
Yikes!
The blade damage is dramatic, but really, the whole thing is junk now: all blades, disks, the shaft, the stators, the bearings.
They're now back way farther than when they first started the overhaul.
At colossal expense, for sure.
Non replaceable ..Scrapped
A turban has no stators or bearings
It can be repaired and my plant the same thing happened a 50 megawatt was dropped a strap broke 1 year later GE delivered it and installed it.
You have no knowledge of turbins,thete ate no stators or bearing on a turbin.
Lol Will, the stator is the name of the part that goes in between the turbine blade sections in order to prevent the gas from rotating as it flows through the turbine, and the bearings are clearly visible in this video…
Thats the most expensive bang i ever heard....
QUICK FIX: manually bend each blade back and just eyeball it.... before the boss finds out. :p
wouldn't want to be around it during startup though!
@@prestonburton8504 Balance-smalance... Onwards and upwards.
Nope!
Out of all the crane accidents I've seen in videos or read about, this is the first where a winch failed. It's usually a cable or some part of the actual rigging that fails. Either way somebody is out a chunk of money even if nobody gets hurt. Glad nobody was hurt in this one.
"At Farmer's Insurance, we know a thing or two because we've seen a thing of two!""
Also at Farmers insurance: Drops are not covered
That guy at 2:25 should thank his lucky stars he wasn't a gooey puddle under that. A few seconds later he would have been.
That guy sure had a guarding angle that day.
Oskar Enback Junkka was it an obtuse or acute angle?
***** Obviously, obtuse.
***** msotil
I would guess on an (a)Cute Angel ;)
no body will go under load in any way...that guy was also doing the same to check installation...safety guys never allow to stand under even when one blade is being installed that was a whole set of Compressor and turbine with rotor...
Ooops.
P.S Skip to the 3 minute mark to save yourself the *agonising suspense* of waiting for the inevitable.
Yup - love to know more about this one. So sad, seeing finely constructed hardware destroyed by cheap shit castings in the crane. I'm guessing that was some sort of transmission shaft with busted off engagement dogs. It explains that mechanical scream just before it came ALL the way loose. No excuse for not using forged components in that drive train.
"Uh, yeah... I just pissed myself... Over." "That's a big 10-4. So did I. Over."
Christ those two guys down in the area close to where that turbine is mounted were very luck to have been able to clock themselves out that day!
I used to work for GE as a project specialist, One of the engineers gave me a copy of this 3 years ago.... This was in a plant in Germany... I remember this. thanks for posting it...
Ohhhh, that grain and the clean snap of cast metal failure.
Harbor freight crane.
I spit my drink out over that. Oh my God, so true.
Still, I can't stop buying certain crap from them.
phuturephunk
Neither can I. They sell some oddly specific things at rock bottom prices.
LMAO
Lol at harbor freight has a decent warranty plan
phuturephunk It's still funny though.
About that couplea million dollar turbin' we just bought.... yea... it was nice an all but we kinda need another one, hope it's no big deal.
almost dropped a tear here, what a beautiful turbine, and is gone in seconds, because a fucking crane.
loss like this can bring down a company
+GeneralWagner Is the turbine even salvageable? As in re-machine and balance, or just build a new one??
+bonjourmssr Yes its salvageable but very expensive, and it will cost 1-2 years. The rotor is too damaged. 180 degree on the underside, and in the upper center from the traverse impact. Even the underside of the housing, wont look well.
Mostly there will be replacement from another powerplant, which has gone offline. If there are more turbines of the same type in one plant, there is often a replacement rotor in stock.
The guy should have reached out and grabbed it to stop it from falling.
Jack Frost is this a joke?
@@reefy5316 The big question is--were you joking when asking me if I was joking?
Jack Frost no actually theres no way he couldve grabbed such a thing despite the manliest man he can emit
@@reefy5316 Do you think that the 33 "thumbs up" that my comment got were agreeing with me, or that they were laughing at my joke?
Jack Frost ?????
This poor Crain Operator most likely received a lot of "Atta-Boy's" & pats on his back for the many good lifts in the past. But it only takes one "O-Shit" to wipe all them Atta-Boy's all out and lose your job.
Actually it's the entire factory's fault
The turbine weighed 75 tons
The crane was rated for 60 tons
Worked on many a steam and gas turbine rotor swap as a millwright with no problems, that rotor would weigh less than the cover which was removed first, the crane would be rated to handle the cover weight, it appears the hoist coupling failed.
That sling held, crane didn't.
Yeah looked like they had it rigged right. Spreader beam and plenty big enough straps. I have been involved in many rigging evolutions and you can get complacent sometimes.i worked in the shipyard and sometimes because of space constraints you HAD to get under the load in order to land it. or refuse and lose your job.
Load brake not adjusted properly was another issue a former crane operator brought up.
I hope the one who did the maintenance has got some friends in South America to hide
I swear to God.......That's how we got it!!
Lol
***** Oh, ok. Here is another one. It's invisible and no one can touch it.
Gonna need a _lot_ of duck tape for this one
As the saying goes, never be underneath a hanging load.
especially sharp, pointy ones :P
That is one huge aw-shit!
"Dropped Object!"
I’ve done every part of this procedure many times, mostly as the crane operator, the notorious weak link of those crane’s were the load brake being not adjusted right, that one was having trouble holding the load, you can hear the motor over rev, this can cause multiple things to fail, usually the gearbox or coupling. They dropped the stator at my plant after I retired and killed a boy on the turbin deck.
Wow, thanks for the inside info with the load brake. I'm gonna say that you are spot on with your diagnosis. I'm assuming this isn't stateside so no OSHA report to read. Again, thanks. - Surry Virginia
Also, it's almost hard to believe that all that instant destruction came from the failing of a relatively inexpensive "LoveJoy" coupling.
insurance will cover it?
Plop the turbine assembly down in front of a modern "art" museum and it'll look a hell of a lot better than the usual crap they got..........
Darth Belal To quote artists: "They would not understand". Engineering = useful art.
Kousheng nuclear power plant in Taiwan has an old turbine rotor on display at their entrance, sitting out in the rain, of all places.
I wonder just how long it took to decon that thing to free release it, considering it's a BWR plant, and the turbines run on primary steam. :-o
Luckily, it seems that no people were injured in this accident. That's a very positive piece of information. Yes, the turbine is completely destroyed (since it cannot be balanced properly again, no matter how carefully it is repaired), but it's just a block of metal. A value of $6.5 million can be produced pretty quickly by a small team of people, but there is no monetary value that could compensate for human health or life.
lol this is so painful to watch. the whole ingeneering masterpiece just a pile of junk in mere miliseconds
I do not like the nature and the size of that grain in the metal at 3.49.
+Carmel Pule' I was thinking the same thing. I don't even know anything about metal, but it just doesn't look right to me.
+AfrewSpines It's Okay.... Neither does Carmel Pule apparently.
Looks like a cast coupling? I've seen this type of metal used on couplings for 7.5 hp pumps and they take a crap in basically the same way.
+semmtexx thats a "fenner"coupling- used in the EU -fenner taperlocks adapt the coupling to the shaft--seen these in screening plants--when one looked like this on a plant, someone took a maul to it,because they forgot to loosen the 2 allen head screws around the taperlock to close the gap between the coupling halves.
+Carmel Pule' I thought the same exact thing....and then I thought....wtf is that metal doing there in a high load situation.
Hear those pops right before? Those mean RUN. I worked on these for a living. Welder, welding inspector, rigger, crane operator. Retired now
"Gas Turbine Accident" that sounds like something id enjoy
Just sell it to Malaysian Airlines with the next batch for 10% off. They'll buy anything.
***** It was an attempt at sarcasm. sorry you didn't get it.
They had it lined up good because it fell right into place.
@donnactrc
where exactly from? the compressor end or the turbine end?
The crane operator must've been so relieved when it became clear that the failure occurred because of the actual crane breaking, rather than his negligence
They still drug tested him afterwards.
@@DrLeroyGreen well, yeah. But presumably he wasn't on drugs.
Looks like a GE Frame 9E. Wow that's an expensive failure
i know its been a long time but if you are around- whats the mw rating for this guy?
@@prestonburton8504 140MW ish
@@Omerta1911 wow! thank you!
@@Omerta1911 I may be mistaken, but I recall reading that this was actually a Siemens turbine.
I saw a replacement gas turbine on its stands waiting to be put in at a Nuclear Power plant around ten years ago. It didn't look to be real heavy. Not over 50000 lbs. A crane like the one that failed must have gotten their parts cheap or it wouldn't have failed. I'm sure it was rated well over what ever it weighed.
But then a worker removing the cover of the turbine being replaced was throwing/flipping a wrench in the air while standing on the cover. This was in PA so who knows.
can you tell me how many compressor bolt hols your "18th stage" has? 15 or 16?
Harbor Freight lifting equipment?
+janj0n How did you know!!! looks like it to me.
+rear speaker the steel ropes broke - right? or did the whole crane collapse?
out of curiosity - who did the Management fuck on this one?
+A.H. Shukry IMO, lack of daily inspections especially before heavy lifts like this---looks like the bearings at the input shaft of the gearbox failed, causing the shaft to load sideways under load, when the fenner coupling failed the input shaft broke thru the brake band asmby., causing the gearbox to freewheel, dumping the load, but thats my 25 cent review of this--mgt. saved a dollar, but they f%$#@ed themselves here!!!
Top comment of the year....
janj0n
whups!, ya let the bean counters do the talking, save a few bucks!, are you sure that part needs replaced?, this part is the new, and improved version!, it'll work much better.
Don't worry Jim....the maximum load rating is a guideline...these things can handle twice the recommended max...OH HOLY SHIT!!!! What do we do Jim? Jim??? JIM???? where are you running Jim????
Nothing a truckload of duct tape can't fix.
"Get the grinder!, it'll buff out."
I finally had to leave my job at the turbine factory. Yeah....after I was FIRED, there was a lot of tension in the office.
That'll buff right out...
@ 2:17 the guy in the yellow helmet very lucky
NEVER stand under a lifted load, EVER
bbigrocker1 he wasn't under it. that is why he didn't die.
Jeffery Smith being UNDER is not a requirement for dying when heavy shit is falling
Jeff Spicolli, "My old man is a television repairman he has this ultimate set of tools, I can fix it, I can fix it."
"Wait a minute, what do you mean when you say "I am fired?" "
Stress point- where forged hardened steel should have been used instead of cast on that particular component? I do not know, just saying. Thank you for the excellent video. It is definitely a learning experience for all, and I am glad no one was hurt.
it'll buff out.
This also gives new meaning to "bearing crush"!
The buzzing sound right before the fall makes me think that his was a brake failure on the crane.
Go pee in the cup... Seriously though, it sounds to me like the winch broke. you can hear gears screaming and stripping right before the earth-shattering KABOOM!
Talk about the sh...hitting the fan.
Wouldn't that be the fan hitting the Sh..?
This is why I never stand under compressors.
Now , send the turbine to museum
Nailed it! good job boys lunch time.
Looks like an average day at a Eskom power station!!!
Viewed it again and you're correct. I was still thinking about the accident when I typed that. That fellow in the yellow hard hat doesn't know how lucky he is to be alive.
What failed?
i work on gas and steam turbines for a living and this is a gasser. you could say this is the quick way of setting the rotor.the rotor itself is around 15mil let alone the other damage to the turbine itself.
This is obviously a case of Framistan modulator overpressurising the Finnigan spleen joint. Or is it spline joint.
Actually it was an over-charged flux capacitor bearing.
I knew that...really, I did.
Ah well, you learn from taking shortcuts and buying cheap material. That's China for you.
"Nice job guys. We finished quick today"
That is why you never stand under a load.
Eh, it landed mostly in place. A little wax and that will buff right out.
I'd say lack of maintenance of the crane.
I agree with you. But you know sometimes shit just breaks despite your best efforts.
No, the crane had an operating load of 60 tons, that turbine weighed 75
WHAT IN THE HELL WAS THOSE GUYS DOING UNDER A SUSPENDED LOAD LOCKS LIKE CABLE BROKE IN THE LIFTING BLOCK !!
The lovejoy coupling failed, so the gearbox freewheeled the whole way down with nothing to stop it.
+monelfunkawitz nailed it!!!!
Just a little duck tape and it will be fine!
that guy in the bottom was lucky he mover 2:24
its a GE Frame 9 machine from General electrics. it happens on a dutch powerplant named harculo near Zwolle.
+Jochum Bakker en die hele turbine is flink naar de.. vaantjes haha
+Jochum Bakker No way, this is not GE machine. It's not a Gas Turbine at all so Frame 9 shouldn't be mentioned in first place, it's a steam turbine and rarely this type of turbine is used in power plant because of its inefficiency.
That should serve as an explanation why you never ever stand under a suspended load. Like the guy to the left did shortly before it came crashing down. At least it looked like he was under it.
very nicely bedded ) a job well done.
Lucky for them it fell right into place! :)
That turbine rotor had to weigh at least 50 tons. When that rotor fell everyone in the power plant must have felt the floor jump under them and heard the sound of the crash.
Oh wow looks like the yellow piece snapped off. How long does it make to make a rotor like that?
Like a glove!
..but why is there an edit @ 2:28 ?
Because it probably took forever till it dropped
Looked like the Hillary Clinton campaign. :p
jestness j OHHHHHHHHHHHH ALL FEMINISTS ARE TRIGGERD OHHHHHHHHHHHH!!!
Nomeclature Issue:
STEAM TURBINE is a device that extracts thermal energy from pressurized steam and uses it to do mechanical work on a rotating output shaft.
GAS TURBINE, also called a combustion turbine, is a type of internal combustion engine. It has an upstream rotating compressor coupled to a downstream turbine, and a combustion chamber in-between.
Thanks to God no one was hurt, there was one technician very near the incidnet.
The Turbine rotor is badly damaged. It seems either the safe working load of the overhead crane was close to the turbine rotor weight or the overhead crane was not inspected and certified for such critical heavy lift for long time.
Fire it up, I'm sure it's fine.
This is the problem when you turn a bunch of drunk union members loose on a project!
Who has been doing the Crane inspections? Also when we did a heavy lift at the Power Plant on a Steam Rotor fitting in place and I was the Crane Operator when I worked there during one of our turnarounds. There was eyes on everything and QUIET during the lift. Wow very expensive. Thank god no one was killed.
+kc5hgv I was wondering why there was so much noise and normal day to day sounds going on during that lift. I even said out loud to the screen....Yo shut the fuck up....we are moving something heavy here... Everyone needs their ears on and eyes open at this moment.
+SquillyMon +SquillyMon Almost seems like they didn't have a foreman there at all. Just a bunch of grunts told to get it done with no former experience doing so.
"Just drop it here they said. It will be fine they said..."
skip to 2:24 if you want to see it.
Always check your gear kids, and watch your operating evenlope
Maybe I shouldn't be watching videos like this while in the middle of implementing my first overhead crane in my test lab.....
+CafeBikeGirl why.its a good idea.....
+CafeBikeGirl Or you should, a good reminder to get your equipment inspected and tested by competent test companys and to never stand under a load. Nothing like a good graphic example to get safety messages across.
One of the blades of the turbine was bent in the mishap. A worker was able to take a ballpen hammer and tap out the metal. The turbine was up and running after only a minute and twenty-two seconds after occurrence.
Well that's one way to do it. Larry, curly and Moe couldn't have done it better. Another job well done. Give those boys a cigar :)
Kramer from Seinfeld: INSTALLED!
can never be balanced again
...coupler looked like it was made of pot metal
Blijft telkens weer waanzinnig als ik dit filmpje terug zie.