Always informative and relaxing with Dave. I've no intention of ever doing this but just like watching the videos. As usual Dave get's the job done with ease as he has a myriad of adapters, drifts, tools etc. As a one off DIY operation it's just not worth it. I guess I could get 3 wheels done at the LBS before I covered the outlay on these essential pieces for this overhaul...
not only the old version needs the special tool for the freewheel. I have a HU 1900 from march 2022, with the same hub DT 370 ratchet LN18 than the H1900, and just after 6500km I have some play inside, I need to change the bearings, one is rusty and the other one as a lateral play, and surprise, now that it is open, I need the special tool. Expensive, do not last more, and need a special tool...
I have a wheel like this, but micro spline. and it doesn't have the spacer like the one that goes before the freehub, where did you get the manual image of this model? I'm not finding
I always watch your videos. I also own an H1900.I overtightened the thru axle and wore out the freehub spacers.I can no longer remove it with my fingers.Any ideas?
Hi, sounds like it needs a strip down and new parts where the existing ones are damaged, there is a great hub slit diagram from DT swiss with part numbers, if you let me know the part numbers you need I will post you some as long as your in the UK
I don't understand why you are greasing the bearings when you put them back in? Is it to make it easier to slide in? I thought the idea was to make the inside of the bearing do all the sliding/rolling, and not the outside?
"Why do you lubricate the outer part of the bearing?", wow, it's strange that you ask such a question, after the fact that every service manual mentions it, even logically speaking it is probably easier to reduce metal-to-metal friction when mounting the bearing by using grease , a bearing greased from the outside should theoretically be easier to fit into the hole.
@@TheYorkshireBikeMechanic In that case what is our next step. Trying with some penatraiting oil? Also what how can I find the tool that you put the wheel on, the one with the plastic top. And what is that freehub holder, I can't find that eather.
@@TheYorkshireBikeMechanic Thanks mate your a legend. I been watching your videos as i just got a Trek Rail 9.8 XT gen 4 for the hills here in North Devon, i love all the tips you have done. Have a few wheels that i need to service, DT Swiss back wheel from my Rocky Mountain Pipeline C70 lying around. All it needs bearings put in.
You didn't happen to measure the rotor side clearance from the end cap? 19mm? 15mm? Cheers! Hey Dave how does the XD FH driver hold up? I've worn out 3 HG bodies because the cassette chews the bejesus out of the splines 😉
Might sound silly but to double confirm,. Do these fit regular bike frames 😅🤷🏼♂️ I got my self the bbshd and it's stressing the crap out of my 'MTB' wheel
Where do i get this handy tool for working on freehub bodies without damaging them at 20:40? Is there a version to work with Shimano Micro Spline too? Would be nice thx!
Always informative and relaxing with Dave. I've no intention of ever doing this but just like watching the videos.
As usual Dave get's the job done with ease as he has a myriad of adapters, drifts, tools etc. As a one off DIY operation it's just not worth it. I guess I could get 3 wheels done at the LBS before I covered the outlay on these essential pieces for this overhaul...
Yes, if your just doing the odd one it's not worth it
thank you very helpful.
Glad it was helpful!
Brilliant dave, thanks for the footage my friend 😊❤👍🇬🇧stay safe and sound. I've now decided on DT instead of hope. Do DT come in other colours 😊👊
Thanks for watching and your comments, only black/white im afraid.
Nice one lad bobs yeah uncle & fannys your auntie 👍 proper job thank you for showing me that very well explained step by step cheers 🍻
Glad you enjoyed it
Another great video, thank you for continuing to do these.
Glad you like them!
Thanks for that Dave really enjoyed that one
Your welcome
These are good all round wheels which I use on the majority of my rentals. I do prefer the XD Driver for longevity. Great Information thanks Dave
Thanks Colin
Great job! Thanks for that mechanical content!
Any time!
Great video, very informative!
Glad it was helpful!
Great video Dave 👍🏻
Glad you enjoyed it
What is the size of the bearings in the freehub?
I feel like I want to drive the 4 or so hours to Yorkshire just to get you to service my bike lol
Crack on, give us a call to book it in
Send it off,,, or go mate, well worth the journey 😊👊
great explanation. Bravo!! 👏👏👏
Hi, thank you for watching and your comment
not only the old version needs the special tool for the freewheel. I have a HU 1900 from march 2022, with the same hub DT 370 ratchet LN18 than the H1900, and just after 6500km I have some play inside, I need to change the bearings, one is rusty and the other one as a lateral play, and surprise, now that it is open, I need the special tool. Expensive, do not last more, and need a special tool...
Hi, yes the tool is essential im afraid
Thanks
No problem
Thank you for being a Super Fan too.
Thanks🥋
Youre welcome
Good stuff
Thank you
I have a wheel like this, but micro spline. and it doesn't have the spacer like the one that goes before the freehub, where did you get the manual image of this model? I'm not finding
Hi, here you go, www.dtswiss.com/en/support/manuals
I always watch your videos.
I also own an H1900.I overtightened the thru axle and wore out the freehub spacers.I can no longer remove it with my fingers.Any ideas?
Hi, sounds like it needs a strip down and new parts where the existing ones are damaged, there is a great hub slit diagram from DT swiss with part numbers, if you let me know the part numbers you need I will post you some as long as your in the UK
important question if this video is to be used by diyers like me : what are each tools and where to get them thanks
Hi, for a decent set www.amazon.co.uk/Enduro-Unisexs-BBT-013-Service-Chrome-Plated/dp/B07KFN1J78
I don't understand why you are greasing the bearings when you put them back in? Is it to make it easier to slide in? I thought the idea was to make the inside of the bearing do all the sliding/rolling, and not the outside?
Hi, thanks for watching and your comments. the grease acts as an anti seize for future maintenance
"Why do you lubricate the outer part of the bearing?", wow, it's strange that you ask such a question, after the fact that every service manual mentions it, even logically speaking it is probably easier to reduce metal-to-metal friction when mounting the bearing by using grease , a bearing greased from the outside should theoretically be easier to fit into the hole.
@@lukasbad5646 Funny you have such low self-esteem.
brilliant guide! unfortunately the dt swiss ratchet ring didnt become lose. instead my tools got bent :/
Sorry to hear that, they can be super tight
@@TheYorkshireBikeMechanic In that case what is our next step. Trying with some penatraiting oil? Also what how can I find the tool that you put the wheel on, the one with the plastic top. And what is that freehub holder, I can't find that eather.
Hi mate what is the size of the brass drift you use, width & length. In the past i had used other tools to do that.
Hi, Thanks for watching, Ive tried to find it in my drawers but its disappeared. I will look for it some more, if I remember is was 15mm x 150mm
@@TheYorkshireBikeMechanic Thanks mate your a legend. I been watching your videos as i just got a Trek Rail 9.8 XT gen 4 for the hills here in North Devon, i love all the tips you have done. Have a few wheels that i need to service, DT Swiss back wheel from my Rocky Mountain Pipeline C70 lying around. All it needs bearings put in.
You didn't happen to measure the rotor side clearance from the end cap? 19mm? 15mm? Cheers!
Hey Dave how does the XD FH driver hold up? I've worn out 3 HG bodies because the cassette chews the bejesus out of the splines 😉
Hi, All hubs are 18.4mm from the outside of the rotor mount face to the end of the endcap, that applies to boost and 142 hubs
Might sound silly but to double confirm,. Do these fit regular bike frames 😅🤷🏼♂️ I got my self the bbshd and it's stressing the crap out of my 'MTB' wheel
Hi, could you explain your question please
Where do i get this handy tool for working on freehub bodies without damaging them at 20:40?
Is there a version to work with Shimano Micro Spline too? Would be nice thx!
Thanks for watching and your comments, the one I used was made by Chris King tools, Im still looking for a microspline holder
Isn´t the "cog spline wrench MS" of "Chris King Universal Hub Tool" fitting for Shimano Micro Spline? Can it be bought alone without the whole kit?
which is the mark of a small bearing?thank you
can you give me a time stamp?
@@TheYorkshireBikeMechanic I found the number of the small bearing 15x24x5. Thank you
What's the part name of the freehub XD vice clamp. Don't give all our secrets away
Hi, Thanks for watching and your comments, we made it ourselves
@@TheYorkshireBikeMechanic out of what?
Alluminium but there are 3d printed ones, google search for freehub service tool
I have HX1700 and take a part much more easy.
Hi, Thanks for watching and your comments, happy new year