The faster, easier way is to use a laser level. You can shoot a line on almost every stud on a floor all at once. And vertical lines too, to keep chases in the ceilings straight as well.
@@The360ElectricianI have a Makita 3 way laser, not that I'm brand loyal or anything, it was just the only one at Home Depot at the time that had the features I wanted. It shoots a horizontal line, a vertical line, and a plumb dot, or all three at once. And you can get a tripod for pretty cheap too. I use the hell out of it. I line up rows of lights, shoot lines for drilling, locate lights perfectly above counters/islands/sinks, shoot lines for boxes, and it even works pretty good for things like leveling conduits, or shooting a line for positioning clamps. If you get used to using it, it's a super time-saver. Well worth the cost.
@@bryanherman1035 Getting a laser level to the right height can be a pain . So the key is getting a tripod that can be adjusted to all sorts of heights - and one that won't tip over easily . The thread on the bottom of the Bosch GGL 2-20 is a 1/4 " course thread - which I think is the same as a camera tripod . . Tip when working on a fence outdoors , I get a 3 or 4 foot length of 5 / 16 " vinyl tubing , fill it 1/2 full with water , and duct tape the ends together - then use this as a level . This is way better than any expensive level . . .
One other point about a laser level - use it to mark the height of all your outlet boxes and switch boxes . I can't find anything in the electrical code that specifies height of the outlet boxes , but when they are all the same height , the quality of the work looks much better . .
Looks like 12 awg romex you are running. You know I bought a 246 foot spool of this which was made in the States Do you find the yellow jacket on this is super soft ? .
In the LA locations we use only 2 suppliers and Home Depot / Lowes when emergency. I think Southwire jackets are the best. They snap off good when razon bladed and strip nice when going along the wire. I have used other brands and found "cheaper feeling" wire an hard jackets as well.
I'm not sure how different the electrical code is in the States , but here in Canada , there is a book called the Ontario Electrical Code Simplified . It has the answer to just about every question anyone could ask about residential electrical code. Its about $13 and most of the home building box stores sell it . I figure almost every rule in the electrical code is because someone paid the price . .
I find it faster to put my elbow in my hip, lock wrist/arm and start drilling. That way no reason to bend for each hole with template, also can keep both hands on drill. Way less fatigue constantly bending for 28" or whatever template height you use.
Retired now but can appreciate this. You do have less "drag" when pulling. Having a benchmark is good for rookies so you don't end up with highs and lows. Neatness makes a statement about the quality of the work to inspectors and anyone who see's it.
@@The360Electrician If you want to do residential work find a reputable contractor who specializes in that or if you want commercial or Industrial work look for that. Maybe you want to try all 3. Many contractors do everything. Then when you've found the right contractor show up for work early. Neat and clean appearance especially if your doing residential work and going into peoples homes. No ripped pants or shirts. No skulls and crossbones. No metal chains, rings or body hardware. Don't become a ground rod. If you have a small religious medal make sure its tucked safely inside your shirt and its not going to pop out. Look like a professional your representing your employer and yourself. If you like what your doing get extra training in it. Learning on the side while working can give you a greater appreciation for what your doing. Get familiar with the NEC and know how to use the book and look stuff up. Ok that's more than two things but those are the basics of starting out. Where abouts are you ? I've been to Montana and have friends in Livingston and Helena.
I try to stay above the four foot drywall so the drywall guys can slide it in without having to go above your wire. Try to think of everyone helps keep my work from being damaged. A lot of people out there they just don’t give a fuck about others work.
Thank you, it's funny why contractors think this wastes time. I did 100 holes in perfect line and roped myself in 2 hours. With all the other benefits it's a no Brainerd. Now my newbie knows exactly what we expect. Thoughts?
@@The360Electrician i will try your way on the next rough-in. I'm always ready to learn, but instead of template I will put a laser on tripod in middle of room.
Not a huge fan of lasers. Batteries, set up and can't go around corners. This method you just keep on going. Try both in one room and see what's better for you and let us know. THanks. PS what state are you tuning in from?
Great idea. I always forget to get the extenders. Do they have a good locking one so my bit doesn't get stuck? Im my eadly years We used an extended bit to go across a thick beam and ended up leaving the entire bit in the house...lol a little gift for the client
No spade bits, auger bits. It's more expensive, but it goes through wood like butter and can also chew out nails. I have 18" auger bit and I drill top plates without ladder, you make a good point with extender.
The faster, easier way is to use a laser level. You can shoot a line on almost every stud on a floor all at once. And vertical lines too, to keep chases in the ceilings straight as well.
What make and model do you like to use?
@@The360ElectricianI have a Makita 3 way laser, not that I'm brand loyal or anything, it was just the only one at Home Depot at the time that had the features I wanted. It shoots a horizontal line, a vertical line, and a plumb dot, or all three at once. And you can get a tripod for pretty cheap too. I use the hell out of it. I line up rows of lights, shoot lines for drilling, locate lights perfectly above counters/islands/sinks, shoot lines for boxes, and it even works pretty good for things like leveling conduits, or shooting a line for positioning clamps. If you get used to using it, it's a super time-saver. Well worth the cost.
@@bryanherman1035 Getting a laser level to the right height can be a pain . So the key is getting a tripod that can be adjusted to all sorts of heights - and one that won't tip over easily . The thread on the bottom of the Bosch GGL 2-20 is a 1/4 " course thread - which I think is the same as a camera tripod .
.
Tip when working on a fence outdoors , I get a 3 or 4 foot length of 5 / 16 " vinyl tubing , fill it 1/2 full with water , and duct tape the ends together - then use this as a level . This is way better than any expensive level .
.
.
One other point about a laser level - use it to mark the height of all your outlet boxes and switch boxes .
I can't find anything in the electrical code that specifies height of the outlet boxes , but when they are all the same height , the quality of the work looks much better .
.
Looks like 12 awg romex you are running. You know I bought a 246 foot spool of this which was made in the States
Do you find the yellow jacket on this is super soft ?
.
In the LA locations we use only 2 suppliers and Home Depot / Lowes when emergency. I think Southwire jackets are the best. They snap off good when razon bladed and strip nice when going along the wire. I have used other brands and found "cheaper feeling" wire an hard jackets as well.
@@The360Electrician I couldn't find a manufacturer - the spool says Made in USA plant 2201 .
I'm not sure how different the electrical code is in the States , but here in Canada , there is a book called the Ontario Electrical Code Simplified . It has the answer to just about every question anyone could ask about residential electrical code.
Its about $13 and most of the home building box stores sell it .
I figure almost every rule in the electrical code is because someone paid the price .
.
Where is the micromanaging guy behind and telling you how to do it better hahaha
The guy that signs the checks? 🤑
@@The360Electrician good enough!
Thank you again first day okay 😅
I find it faster to put my elbow in my hip, lock wrist/arm and start drilling. That way no reason to bend for each hole with template, also can keep both hands on drill.
Way less fatigue constantly bending for 28" or whatever template height you use.
I hear you, but I did 100 holes in 15 min one handed. It looks like a machine did it. Absolutely straight and easy to rope
Retired now but can appreciate this. You do have less "drag" when pulling. Having a benchmark is good for rookies so you don't end up with highs and lows. Neatness makes a statement about the quality of the work to inspectors and anyone who see's it.
EVERYONE, WORDS OF WISDOME RIGHT HERE! Thanks for commenting. Where are you tuning in t from?
@@The360Electrician New Jersey, 49 years in the field and 41 years as a licensed contractor
That's amazing. Would love to hear more one day. How was contracting in Jersey? What's the 2 best piece's of advice for those starting out?
@@The360Electrician If you want to do residential work find a reputable contractor who specializes in that or if you want commercial or Industrial work look for that.
Maybe you want to try all 3. Many contractors do everything. Then when you've found the right contractor show up for work early. Neat and clean appearance especially if your doing residential work and going into peoples homes. No ripped pants or shirts. No skulls and crossbones. No metal chains, rings or body hardware. Don't become a ground rod. If you have a small religious medal make sure its tucked safely inside your shirt and its not going to pop out. Look like a professional your representing your employer and yourself. If you like what your doing get extra training in it. Learning on the side while working can give you a greater appreciation for what your doing. Get familiar with the NEC and know how to use the book and look stuff up. Ok that's more than two things but those are the basics of starting out.
Where abouts are you ? I've been to Montana and have friends in Livingston and Helena.
I Actually use a laser but this is good idea. Thanks for the tip!
I try to stay above the four foot drywall so the drywall guys can slide it in without having to go above your wire. Try to think of everyone helps keep my work from being damaged. A lot of people out there they just don’t give a fuck about others work.
You are my kind of electrician.
EfficiAnt!
Thanks we think so. Where you tuning in from?
@@The360ElectricianI’m just teasing. From Charlotte. Love all your content. 💪
Systems are so necessary.
Thank you, it's funny why contractors think this wastes time. I did 100 holes in perfect line and roped myself in 2 hours. With all the other benefits it's a no Brainerd. Now my newbie knows exactly what we expect. Thoughts?
@@The360Electrician i will try your way on the next rough-in. I'm always ready to learn, but instead of template I will put a laser on tripod in middle of room.
Not a huge fan of lasers. Batteries, set up and can't go around corners. This method you just keep on going. Try both in one room and see what's better for you and let us know. THanks. PS what state are you tuning in from?
@@The360Electrician the state of Ontario, Canada 😉
My pro hole drilling tip: for vertical holes, I use a large drill bit extender so I drill the top plate without a ladder! Much faster and much easier!
Great idea. I always forget to get the extenders. Do they have a good locking one so my bit doesn't get stuck? Im my eadly years We used an extended bit to go across a thick beam and ended up leaving the entire bit in the house...lol a little gift for the client
No spade bits, auger bits. It's more expensive, but it goes through wood like butter and can also chew out nails. I have 18" auger bit and I drill top plates without ladder, you make a good point with extender.
I’ve used the 5ft flex augers for the same myself.
Always used Greenlee nail eater drill bits for old work. Cuts thru a hidden 8 penny nail and remains sharp.
@@JohnThomas-lq5qp They still make them? I'll have to reach out to Greenlee!