me too !I tried 8 times following directions that came w the lock. Once I did the learning part it worked. Why does Kwikset not include that in the directions.
Thanks a million...Kwikset emailed my sister the wrong manual for this lock which caused me to reset all codes & without your video I was stuck like chuck because no other video showed the proper reset info! Thanks again.
Thank you for the videos! We had problems with ours out of the box and resetting was the key. I followed all your instructions and we are good now. Thank you! We are visual people so your vids are appreciated
OK. So. I don't get it. After u do this? How do you erase th code and put your code in? What's the difference between learning it. And user code and PC? It's so confusion.
Thanks bro could not figure out why when I pressed the kwikset button to make the electronic lock work, that it was not working the instructions has this process of resetting at the bottom of the page and the part about pressing the zero to learn it after u reset it and put in the PC code was the part that I was missing thanks a million bro!...💪🏾💪🏾💪🏾💪🏾
It didn't work for me but I probably have a different type of lock but thank you I'm going to keep trying to find a way to fix this. The slot came with the new house I just bought and I don't have any instructions on how to do anything if anything I'm just going to remove it and start from scratch
I keep getting red light. I do the reset and follow your instructions and works up to the point where I press 0 and top button to open and close the deadbolt, but I get a red light? ...I also bought a fresh pair of batteries and till does the same?
IF YOU BOIGHT FROM COSTCO: It's like best buy, almost the same, but not in the details. IT WILL NOT MOVENIN AND OUT, but it will learn right/left, based on where it is unlocked. When you install, make sure it goes back and forth with the lever easy, if not, you need to move the rod 90 degrees and put back on so it will. Next step, do the learn with 0. Now, enter the 0000, kwk(lock) button, 1, kwk, new 4-10 digit code, kwk. Should blink green and beep twice(both). Repeat for up to 6 codes. 3 beeps and red means it messed up somewhere, so if you hit the wrong button, just wait for this and start over. PC is bbn programming code (0000)default, and can be changed as follows: Current pc(0000, default) kwikset button(kwk), 4, kwk,(your new programming code), kwk. Done. Don't loose or forget this number. You will need it in the future.
Thank you so very much for these series of videos. you should have been the one to write the instruction manual. They were very poorly written and your videos were a godsend. Thank you very very much I appreciate it!
Hi, I did a reset, the door look open, did the 0000 an 0 for programing directions but it dosen´t work (red lights), tried it 10 times but dosen´t work every time red lights. If I close manually the look en do the direction process it works backwards (to close you need te usercode and to open just push the kwikset-button. May you had the same problem some day and know the solution. thanks, best regards Kai
i had the same problem. it will only recognize the code if it thinks it is "unlocked" so what you need to do is start with the bolt in the "locked" position (with the bolt sticking OUTSIDE of the door) , enter the "0000" "enter"-it will flash green and beep then start flashing orange, while it is flashing orange, turn the lever so that the bolt is INSIDE the door. NOW, press "0" "Enter". it will run through the program where it comes out, then goes back in, and then beep twice with a green light. now it is programed correctly.
Next feature is the temporary code. Like having an exterminator, electrician, mover, guest, or whatever have temporary access without handing over a key.... programming code, kwk, 9, kwk, new temp code, kwk. This is a one time only code, and won't work a second time, unless programmed in again. Next, disable all electronic function, including all codes: Program code, kwk, 8, kwk. Use the key to lock and unlock and electronic function will return.
How to add User Codes CAUTION: A User Code is used to unlock the door while a Programming Code is a password for making changes to the lock features. 1. Make sure the lock is unlocked and the door is open. 2. Enter your Programming Code - for new installation, default is 0-0-0-0. 3. Press Kwikset. You will hear one beep. 4. Press 1. 5. Press Kwikset. You will hear one beep. 6. Enter a new User Code. It must be 4-10 digits. 7. Press Kwikset. You will hear two beeps if successful. If you hear three beeps, it was unsuccessful. Repeat from step 1 slowly. 8. Test the code: While your door is open, lock it. Wake the screen and touch the random lit digits.Enter your new User Code, then press Kwikset. The door should unlock.
@@weldingandstuff I think mine is broken. I signals it accepts the change, but when I test to see if the Change works... it gives the beeping sound like as if my commad fails. But, big thanks!
Thank you Thank you Thank you! Although the video was helpful, the manual really explains how to learn the code, delete the default code, and set a new code! Very important to delete the default code, otherwise anyone can enter your home by pressing 1234! I was able to set it up in 5 min. Thanks again for sharing.... and I also emailed the PDF instructions to myself for future use.
Reset is the only thing I can figure out lol...I held the reset button for over 5 seconds...just hold it down and you should hear the 3 long beeps. Hope this helps and good luck
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Kwikset 92640-001 Contemporary Electronic Keypad Single Cylinder Deadbolt with 1-Touch Motorized Locking, Satin Nickel amzn.to/2y8VN4D
TRY THE NEW !!!! Electronic Deadbolt Smart Door Lock, LED Touch Screen Keypad, Bluetooth Smart Phone Enabled Keyless Access, Easy to Install, Oaks Smart Lock (Smart Lock) amzn.to/2PGC5bQ
Best Kwikset video I’ve ever seen. So clear instructions.
Thank you so much.
Every time I need to do settings, I watch this.
Thanks heaps! :)
me too !I tried 8 times following directions that came w the lock. Once I did the learning part it worked. Why does Kwikset not include that in the directions.
Kwikset lock on Amazon amzn.to/2Rtcq3C
Thanks a million...Kwikset emailed my sister the wrong manual for this lock which caused me to reset all codes & without your video I was stuck like chuck because no other video showed the proper reset info! Thanks again.
Thank you for the videos! We had problems with ours out of the box and resetting was the key. I followed all your instructions and we are good now. Thank you! We are visual people so your vids are appreciated
Thanks!
Nice work!
This video saved my sanity.
Got the deadbolt direction changed for a new door and the codes installed.
Much Appreciation!
Glad it helped
You save my life literally and my time. The best video and the best explanation. Blessings
After I reset it to factory mode. How do I change the code
Thank you!! Sir you are a genius 👏 only video that explains how to work this thing
OK. So. I don't get it. After u do this? How do you erase th code and put your code in? What's the difference between learning it. And user code and PC? It's so confusion.
That was perfect !, made it very easy
Thank you !!!!
How do I put in another code after i reset it?
THANK YOU!! I was getting SO frustrated. :)
Only video this worked, thank you
Thanks bro could not figure out why when I pressed the kwikset button to make the electronic lock work, that it was not working the instructions has this process of resetting at the bottom of the page and the part about pressing the zero to learn it after u reset it and put in the PC code was the part that I was missing thanks a million bro!...💪🏾💪🏾💪🏾💪🏾
Thank you very much man this is very important
It didn't work for me but I probably have a different type of lock but thank you I'm going to keep trying to find a way to fix this. The slot came with the new house I just bought and I don't have any instructions on how to do anything if anything I'm just going to remove it and start from scratch
You didn’t tell us how to set the new code. only how to zero it out
It is on your battery cover cap.
@@GaryEnjoy that's not helpful
Not helpful, I need to set a new code
how did you remove the cover: the first step? thanks
I keep getting red light. I do the reset and follow your instructions and works up to the point where I press 0 and top button to open and close the deadbolt, but I get a red light? ...I also bought a fresh pair of batteries and till does the same?
Same here😢
Still don't know how to enter a new code ☺️
IF YOU BOIGHT FROM COSTCO:
It's like best buy, almost the same, but not in the details. IT WILL NOT MOVENIN AND OUT, but it will learn right/left, based on where it is unlocked. When you install, make sure it goes back and forth with the lever easy, if not, you need to move the rod 90 degrees and put back on so it will. Next step, do the learn with 0. Now, enter the 0000, kwk(lock) button, 1, kwk, new 4-10 digit code, kwk. Should blink green and beep twice(both). Repeat for up to 6 codes. 3 beeps and red means it messed up somewhere, so if you hit the wrong button, just wait for this and start over.
PC is bbn programming code (0000)default, and can be changed as follows:
Current pc(0000, default) kwikset button(kwk), 4, kwk,(your new programming code), kwk. Done. Don't loose or forget this number. You will need it in the future.
Could you set this lock to lock itself with a time limit just in case you forget to lock ?
Your video too awesome! Thank you so much
Thank you so very much for these series of videos. you should have been the one to write the instruction manual. They were very poorly written and your videos were a godsend. Thank you very very much I appreciate it!
Excellent video! Thank you!
Thank you! Helped me out a lot!
Bro you were helpful!!
Glad to hear it!
I do exactly what you say but after reset and do what you say it only comes out but doesn’t go in ?? Can you help
Hi, I did a reset, the door look open, did the 0000 an 0 for programing directions but it dosen´t work (red lights), tried it 10 times but dosen´t work every time red lights. If I close manually the look en do the direction process it works backwards (to close you need te usercode and to open just push the kwikset-button. May you had the same problem some day and know the solution.
thanks, best regards
Kai
i had the same problem. it will only recognize the code if it thinks it is "unlocked" so what you need to do is start with the bolt in the "locked" position (with the bolt sticking OUTSIDE of the door) , enter the "0000" "enter"-it will flash green and beep then start flashing orange, while it is flashing orange, turn the lever so that the bolt is INSIDE the door. NOW, press "0" "Enter". it will run through the program where it comes out, then goes back in, and then beep twice with a green light. now it is programed correctly.
.
Next feature is the temporary code. Like having an exterminator, electrician, mover, guest, or whatever have temporary access without handing over a key.... programming code, kwk, 9, kwk, new temp code, kwk. This is a one time only code, and won't work a second time, unless programmed in again.
Next, disable all electronic function, including all codes:
Program code, kwk, 8, kwk. Use the key to lock and unlock and electronic function will return.
Thanks. Worked great! 😃
Helped a lot 😀
Helpful. Thank you!
My new kwikset lock will lock using the 0000 code but not unlock. Any ideas?
How to add User Codes
CAUTION: A User Code is used to unlock the door while a
Programming Code is a password for making changes to
the lock features.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default is
0-0-0-0.
3. Press Kwikset. You will hear one beep.
4. Press 1.
5. Press Kwikset. You will hear one beep.
6. Enter a new User Code. It must be 4-10 digits.
7. Press Kwikset. You will hear two beeps if successful. If you
hear three beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Wake the screen
and touch the random lit digits.Enter your new User Code, then
press Kwikset. The door should unlock.
Do you have to press the reset button in the back before doing this?
@@purrpleciity1 Yes. Press and hold the reset button for 5 seconds.
Thanks. I don’t know why but now both , old and new code , both working to unlock 😊
What is the default PC?
1234
time stamp 1:28
@@weldingandstuff I think mine is broken. I signals it accepts the change, but when I test to see if the Change works... it gives the beeping sound like as if my commad fails. But, big thanks!
@@wg4476 Hope you try another one; they are great amzn.to/2rnKKkX
1234
Thank you very much
HELP! How do you set a new code?!?
Thank you sir
Very helpful!!
Found the original manual on website. Here ya go folks!
s7d5.scene7.com/is/content/BDHHI/5066882
Thank you Thank you Thank you!
Although the video was helpful, the manual really explains how to learn the code, delete the default code, and set a new code! Very important to delete the default code, otherwise anyone can enter your home by pressing 1234!
I was able to set it up in 5 min. Thanks again for sharing....
and I also emailed the PDF instructions to myself for future use.
Ty again sir
Ahhh, the missing step NOT in my written manual---pressing the hidden reset button!!
How do i change the code man.
Lol- i subscribe now and hit the thumbs up.
Please help.
Thanks mr sir!!!!
Thank you.
Thanks! This was perfect!
None of this seems to work for me. I don't even get a beep with the reset. I get plenty of beeps for other things and it has fresh batteries.
Reset is the only thing I can figure out lol...I held the reset button for over 5 seconds...just hold it down and you should hear the 3 long beeps. Hope this helps and good luck
I tried and it don’t work.
Ok got your 1234 on my lock, how can i add a new code and delete the 1234?
Try this ruclips.net/video/nBUqc7Ysxr4/видео.html
Try this ruclips.net/video/nBUqc7Ysxr4/видео.html
If only I went to this video before reading the directions on the battery cover. Now, I can't do anything with this lock as nothing I do works.
Help support my videos by pledging $1 per month - you can cancel your pledge at anytime www.patreon.com/weldingandstuff
Thank you!
you need to do this all over again this time dont cover what your doing
Who cares about setting it to 4 zeros? How do we enter our own code!!!
Bro you're a lifesaver!
How do I change the default code after this?
THANK YOU!
So helpful. Thank you!!