OK I just did mine(first timer) I have some tips to share from what I learnt my experience. 1. I overestimated the viscosity of the liquid. It is very light, just slightly thicker than water. This caused me to lower the glass with less care than I needed to, causing air bubbles. You will have a lot of excess liquid, definitely have a feel of it first by trying it on something else (such as on a scrap plastic film, cut it into two and put the liquid in between, have a feel of the liquid and how light it is). 2.mask everything on the sides. If it is your first try it can get messy(like I did). There WILL be liquid overflowing out from the sides. I'm relieved I did not take a shortcut and did mask all the sides with tape. Use normal tape, run it all around so you don't miss anything like the sim slot, mic hole etc. 3. Absolutely make sure there is no oil on the surface, even if really little. Use rubbing alcohol if you have to. Otherwise, the liquid will be hard to stick to it. I had a corner which apparently has some unseen oil, but lucky it was only a small corner so I could get the liquid to stick by pressing it with a fingernail while shining th uv light to cure while I apply pressure. 4. Put your liquid in a circular spot exactly like the video. This ensures the smallest perimeter for volume, which helps reduce possibility of air bubbles. Do not do fishbone or any other patterns which is suitable only for more viscous (thick) liquids. 5. Mentally prepare yourself that once you lower the glass it should be downwards all the way. Do not lift it even by 1mm. Lifting it will cause a large retraction of the liquid which will draw in air bubbles. (Like I did). If that happens, don't give up,lower the whole glass and push out the bubbles which can be done perfectly. This is one place where the low viscosity is actually helpful. You can push out even micro bubbles for long distances with perfect result unlike non uv adhesive. 6. The uv light cures the liquid faster than you think. It takes only about 10seconds to harden the amount at each direct spot below the uv light, between the tempered glass and the screen to a non-flowable state, holding the light at about 1 inch. 7. The end result is so worth it, it actually feels like you are using the screen without tempered glass! It is that awesome! This feels completely different from normal tempered glass. If u tap the screen with the uv light while you are curing the liquid u will hear the sound like you tapped glass, not a plastic sound like if u tap a normal tempered glass. This is because the liquid bonds the tempered glass to the screen on a much more nano level.
Just completed this on my new s10+. 1. I used tape over the buttons and speakers because well...it made me feel "safer" 2. Before placing the protector on the glue, I cleaned it too with the alcohol wipe and wiped dry as well as remove dust 3. Once protector is placed down try not to move the phone. I thought tilting it would make glue go all the way to edges but just caused the proctector to slide 4. I was shit scared as my phone is basically brand new. But it worked so well just take your time. Make sure you're not in a hurry. Relaxed and not needing to go loo or anything 😅
glad it worked for you but i tell everyone that a case with a built in screen protector is the simplest solution i been using them with success since the S8+ my note 9 sits safely in one and i bought one for my pearl white S10+ although i have yet to open my S10+ it's still in it's shipping box it's been there for 2 months now but yea a case with a built in screen protector is a can't miss proposition i swear by them my phones have survived numerous falls on concrete
@@andreiceban438 on some of the cases with the built in screen protectors yes it works but the others let you know that they're cases aren't compatible with the in screen finger print scanner but i bought one where it is compatible
REMEMBER THIS BEFORE DOING if ur first time done it make sure that you put tape on the speaker (important) and button if needed....... bcuz evwn though i change this type of temper thousand time i still use tap to minimize the risk
Just a heads up guys Samsung Galaxy Note 10 Plus 5G. You must tape up the earhole speaker, Power & Volume buttons on the side & the S-Pen Gap area near the bottom of the phone. Why because the Liquid Glue Adhesive will seep into the Buttons & S-Pen causing it to harden and become permanently stuck meaning your whole phone is now fucked lol. Just make sure absorb & dry any access liquid glue oozing out with a cloth or papper towel. UV light at least 30sec to 60sec on top, middle & bottom & edge sides.
This glass is fail if u put this chemical u.v glass yr volume key and on/off key will corrupt and ur phone warranty will be lost If u don't believe me after u put the glass check after one
I'd like to give you a suggestion: the uv lamp starts at the edge. The sticker with "除尘贴" is for you to remove dust from the screen, and the strip sticker is for you to seal the receiver to prevent glue from entering. Personal opinion.
Special note. For someone are not experienced this attempt. DO NOT DO THAT except installed by professional. And also, make sure you have a right tools and also backup UV liquid just in case if there maybe fail at 1st attempt. And final, always level your table seriously because liquid can move by gravity if there not well leveled.
I bought this in Mall and the shop attendant helped me install it. I did pay extra for it but the result and service is worth the extra few bucks.. Many things could go wrong. Thank you for sharing your process. That shop attendant deserve the extra tip.
1st : u should cover the earpiece with some tape to avoid the liquid to sip into the earpiece. 2nd: you shouldn’t press the glass while the liquid is flowing because you will create a rainbow effect once the glue dried due to un even pressure and surface of the liquid 3rd: this uv glue will remove the oleophobic coating of the glass when you remove it in future. Unless you dont care about the oleophobic coating then its okay to use this type of TG.
@@korinnakriskintanar3301 every phone screen will have a layer of coating. It will make water slide very easily. You may watch the video explaining this oleophobic coating as i cant explain it wll to you. If you apply this UV glue, it will remove the coating and this coating cannot be reapply.
@@korinnakriskintanar3301 yes! The UV glue can get in the screen gap (frame and glass) and cause damage to your screen. Samsung for example wont accept your phone if its damage by uv glue. U have to pay for the screen if u were to damage it. Also, if its find its way to your earpiece, its gone, forever because once its cure by the UV light it hardened and it will not be able to be remove unless u changes your earpieces mesh or the earpiece it self. Same goes to side buttons, if u didnt wipe it down before curing it, you may as well say goodbye to your buttons..
If the glue gets into the volume keys and the earpiece would it get stuck and cause problems ? I mean is this really safe for out very expensive devices?
Such a long and fully technical name " Nano Optics Curved Edge To Edge Liquid UV Glue Tempered Glass for Samsung iPhone .." It gives you a feeling that how advance your phone became by just applying a glass gaurd on it as it is ready to connect your galaxy handset directly with the aliens on mars.
I just did mine in s galaxys7edge. GOOD ADVICE: cover with stickers all holes, buttons otherwise you will end up like me with needle trying to remove glue from underneath it ;-/ and some of them not working.
Be careful with the ear speaker front top part, if somehow the liquid gets stuck will block the tiny holes of the front ear speaker so as you won't listen anything!!!
Just a heads up guys Samsung Galaxy Note 10 Plus 5G. You must tape up the earhole speaker, Power & Volume buttons on the side & the S-Pen Gap area near the bottom of the phone. Why because the Liquid Glue Adhesive will seep leak into the Side Buttons & S-Pen causing it to harden and become permanently stuck meaning your whole phone is now fucked lol. Just make sure absorb & dry any access liquid glue oozing out with a cloth or papper towel. UV light at least 30sec to 60sec on top, middle & bottom & edge sides. And Rescan your finger print scanner again afterwards and put sensitivity settings to on max 👍
The background music is really irrigation Use some pleasant instrument music like flute violin etc Really superb installing the curved shaped glass for the Samsung mobile
Одно из адекватных видео о приклеивании стекла с УФ лампой. ОЧЕНЬ МНОГО ВИДЕО ОТ РУКОПОПОВ, будьте бдительны! Опыт испорченных 2-3 стекол, хотя руки растут из плечей и голове толковой помогают Хочу дополнить, данное приклеивать лучше укладывая руками держа за 4 угла. 1.Клей открывается поворотом колпачка (срывается кончик вставленный в колпачек), не сохнет на открытом воздухе (есть время для манипуляций!). 2.Стики (наклейки) в комплекте после протирки спиртовой тканью отходят и становятся бесполезными для заклеивания динамика, кнопок (вкл./откл./регулятора громкости). 3.Клея в тубе больше, чем нужно, НО лучше вытечет, чем его будет недостаточно. 4. В момент укладки стекла на клей, можно, а чаще всего нужно разгонять его лёгким наклоном телефона! (АККУРАТНО - стекло плывет на клею). 5.Клей полимеризуется в течении 1-2 мин. при полном соприкосновении с лампой (проводил ОПЫТ с остатками клея!),превращается в что-то подобное клею-секунда. Автор правильно рекомендует пройти середину и после вытереть (АККУРАТНО - ТОЛЬКО ЗАДЕНЕШЬ КРАЙ, может попасть воздух, НО возможно подлить остатки клея и растянуть зубочисткой!) тряпочкой в комплекте (сухой!) или лучше салфеткой или туалетной бумагой насухо! Не проходить лампой пока не убедишься, что клей во всех возможных отверстиях телефона вытерт. В тот же момент не забываем, что стекло ПОДВИЖНО! - делаем предельно АККУРАТНО! 6.Напоследок хочу добавить, что телефон с выпирающей камерой не ложить на ровную поверхность, клей ОЧЕНЬ ТЕКУЧ и может просто сбежать с экрана! Некоторые продавцы комплектуют пластиковой рамкой для выравнивания стекла, считаю, что она относительно бесполезна (мой опыт!). 7.Приклевал ( держал/перемещал лампу на протяжении 7-10 мин. достаточно основательно). Итогом стало приклеенное стекло с 2 пузырьками на экране (НО посчитал ЛУЧШЕЕ-ВРАГ ХОРОШЕГО!;) и оставил! Надеюсь был вам полезен, желающий вам добра, Павел Никитин) Не снял, потому, что не было 2 камеры, делал долго и чуть ненормативной лексики... Телефон с закругленными краями Xiaomi Mi Note 10 Pro.
I don't want to say this is wrong but I hope nobody is installing like this. When you drop the liquid, then drop the protector but do not press on the screen at all. Let the liquid flow by itself to the whole protector, it will never leak as long as you don't press it. Once all the glue spread, use the light a few seconds at a time around the screen. You'll never have any mess as long as you never press down. This was extremely messy and probably wasted most of the liquid.
i have a quesiton, does applying uv glue lessen the sensitivity of the screen? or its not reading the finger faster? or it improves the sensitivity? sorry my english is bad, i hope you understand and answer. pls thankyou
Hi, thanks for the video. I would like to know if when this protector with its liquid is removed to leave the screen without any kind of protector would there be any residue or mark on the screen? Thank you. Hola, gracias por el video. Quisiera saber si cuando este protector con su liquido es extraido par dejar la pantalla sin ningun tipo de protector quedaria algun residuo o marca en la pantalla ? Gracias.
Question tho... How to remove the glue smell of the tempered glass?? Since I've done the messy way to do this :3 sometimes I could feel the stickiness of the glue whenever my hands gets sweaty
Hi, why did you have another film under the original broken tempered glass screen protector? Was it just an extra film protector for extra protection? Did it not reduce the sensitivity of the touch on phone?
Please provide me a link to but the same exactly glass to buy online. I have tried somany glasses but nothing is fitting like this. This is a perfect glass for note 9.
I can only imagine how many people screwed their earspeaker because of ur lame video! Do not do anything unless u r sure u know how to do it correctly! This is the worst case scenario!
@@DylanJSkittles i had to repair dozen of this way fd up speakers people brought to me! U should read the manual first than talk! Never apply pressure so that the liquid can escape!
@@DylanJSkittles it does not affect 🤮! When the speaker grill clogs with liquid u think sound comes out the same intensity as it used too! Think with ur brain!
@Reese M wiping doesnt help if the glue cures on the speaker grill! U had luck! But still i would bet one grand ur ear speaker is not the same volume intensity as it used to be! Liquid got into pores of 'ur grill!
@@karlosp02 anytime I have done this it has not affected anything. Before curing make sure you take a pin, lightly pick out anything that is in the speaker or ports, wipe clean with rubbing alcohol and then cure the screen. Good as new. Dont assume I dont know what the hell I'm talking about. Who knows if he edited this video, could have cropped out where he cleaned out ports.
Wow you are so stupid then as it comes off more easy than it takes to put it on and with no residues afterwards, but I guess the stupid love only the edges stuck down and wonder why those screen protectors are crappy!
Man you guys love this video you guys are gonna love reading the fucking box instructions to this dump product. Even after I placed some stickers to block the glue to from getting into the speakers it somehow got in it hardened I can see it under light and after being so careful with it I got an air bubble 🤦♂️ you can’t fix the air bubble
OK I just did mine(first timer) I have some tips to share from what I learnt my experience.
1. I overestimated the viscosity of the liquid. It is very light, just slightly thicker than water. This caused me to lower the glass with less care than I needed to, causing air bubbles. You will have a lot of excess liquid, definitely have a feel of it first by trying it on something else (such as on a scrap plastic film, cut it into two and put the liquid in between, have a feel of the liquid and how light it is).
2.mask everything on the sides. If it is your first try it can get messy(like I did). There WILL be liquid overflowing out from the sides. I'm relieved I did not take a shortcut and did mask all the sides with tape. Use normal tape, run it all around so you don't miss anything like the sim slot, mic hole etc.
3. Absolutely make sure there is no oil on the surface, even if really little. Use rubbing alcohol if you have to. Otherwise, the liquid will be hard to stick to it. I had a corner which apparently has some unseen oil, but lucky it was only a small corner so I could get the liquid to stick by pressing it with a fingernail while shining th uv light to cure while I apply pressure.
4. Put your liquid in a circular spot exactly like the video. This ensures the smallest perimeter for volume, which helps reduce possibility of air bubbles. Do not do fishbone or any other patterns which is suitable only for more viscous (thick) liquids.
5. Mentally prepare yourself that once you lower the glass it should be downwards all the way. Do not lift it even by 1mm. Lifting it will cause a large retraction of the liquid which will draw in air bubbles. (Like I did). If that happens, don't give up,lower the whole glass and push out the bubbles which can be done perfectly. This is one place where the low viscosity is actually helpful. You can push out even micro bubbles for long distances with perfect result unlike non uv adhesive.
6. The uv light cures the liquid faster than you think. It takes only about 10seconds to harden the amount at each direct spot below the uv light, between the tempered glass and the screen to a non-flowable state, holding the light at about 1 inch.
7. The end result is so worth it, it actually feels like you are using the screen without tempered glass! It is that awesome! This feels completely different from normal tempered glass. If u tap the screen with the uv light while you are curing the liquid u will hear the sound like you tapped glass, not a plastic sound like if u tap a normal tempered glass. This is because the liquid bonds the tempered glass to the screen on a much more nano level.
thanks for further explanation. The video only showed us what to do and with your explanation I successfly applied the glass to my phone :)
@@chackingnoob You're welcome! Glad it helped! :)
Rick
do you need to apply masking tape or something to the speaker at the top as well? (S9)
Terrific,
Your explanantion was the encouragment I needed to Do it Myself.
@@Bartem_ yes, definitely. Just assume that everything will be wet and mask all. :)
Just completed this on my new s10+.
1. I used tape over the buttons and speakers because well...it made me feel "safer"
2. Before placing the protector on the glue, I cleaned it too with the alcohol wipe and wiped dry as well as remove dust
3. Once protector is placed down try not to move the phone. I thought tilting it would make glue go all the way to edges but just caused the proctector to slide
4. I was shit scared as my phone is basically brand new. But it worked so well just take your time. Make sure you're not in a hurry. Relaxed and not needing to go loo or anything 😅
glad it worked for you but i tell everyone that a case with a built in screen protector is the simplest solution i been using them with success since the S8+ my note 9 sits safely in one and i bought one for my pearl white S10+ although i have yet to open my S10+ it's still in it's shipping box it's been there for 2 months now but yea a case with a built in screen protector is a can't miss proposition i swear by them my phones have survived numerous falls on concrete
@@fallback8314 what do you mean by built in screen protector?
Does the finger print works fine?
@@andreiceban438 on some of the cases with the built in screen protectors yes it works but the others let you know that they're cases aren't compatible with the in screen finger print scanner but i bought one where it is compatible
thankyou
I pray who ever reads this becomes successful.....
I did
Ok
@Buriyani Oneda malli Nice to see the misogynistic Indian culture is going strong
Thank you so much 💖
I think you r coming daily to read it. GAL bro
REMEMBER THIS BEFORE DOING if ur first time done it make sure that you put tape on the speaker (important) and button if needed....... bcuz evwn though i change this type of temper thousand time i still use tap to minimize the risk
Just a heads up guys Samsung Galaxy Note 10 Plus 5G.
You must tape up the earhole speaker, Power & Volume buttons on the side & the S-Pen Gap area near the bottom of the phone.
Why because the Liquid Glue Adhesive will seep into the Buttons & S-Pen causing it to harden and become permanently stuck meaning your whole phone is now fucked lol.
Just make sure absorb & dry any access liquid glue oozing out with a cloth or papper towel.
UV light at least 30sec to 60sec on top, middle & bottom & edge sides.
Iiijumjo ikai
This glass is fail if u put this chemical u.v glass yr volume key and on/off key will corrupt and ur phone warranty will be lost
If u don't believe me after u put the glass check after one
I'd like to give you a suggestion: the uv lamp starts at the edge. The sticker with "除尘贴" is for you to remove dust from the screen, and the strip sticker is for you to seal the receiver to prevent glue from entering. Personal opinion.
I agree
@@someonefrl3982 no we don't understand your language.
I use dust stickers to also guide screen protectors, It's hard to get them completely straight without a little help.
S1 S2 S3 S4 S5 S6 S7 S8 S9
Special note. For someone are not experienced this attempt. DO NOT DO THAT except installed by professional. And also, make sure you have a right tools and also backup UV liquid just in case if there maybe fail at 1st attempt. And final, always level your table seriously because liquid can move by gravity if there not well leveled.
Thanku so much sir 👍I've learnt from you how to install tempered glass on samsung galaxy note 9✌️
I bought this in Mall and the shop attendant helped me install it. I did pay extra for it but the result and service is worth the extra few bucks.. Many things could go wrong. Thank you for sharing your process. That shop attendant deserve the extra tip.
1st : u should cover the earpiece with some tape to avoid the liquid to sip into the earpiece.
2nd: you shouldn’t press the glass while the liquid is flowing because you will create a rainbow effect once the glue dried due to un even pressure and surface of the liquid
3rd: this uv glue will remove the oleophobic coating of the glass when you remove it in future. Unless you dont care about the oleophobic coating then its okay to use this type of TG.
Hello.. what does the 3rd comment mean? Thanks..
@@korinnakriskintanar3301 every phone screen will have a layer of coating. It will make water slide very easily. You may watch the video explaining this oleophobic coating as i cant explain it wll to you. If you apply this UV glue, it will remove the coating and this coating cannot be reapply.
@@xansieva27 geez thanks! That this type of protector DOES "damage" the phone?
@@korinnakriskintanar3301 yes! The UV glue can get in the screen gap (frame and glass) and cause damage to your screen. Samsung for example wont accept your phone if its damage by uv glue. U have to pay for the screen if u were to damage it. Also, if its find its way to your earpiece, its gone, forever because once its cure by the UV light it hardened and it will not be able to be remove unless u changes your earpieces mesh or the earpiece it self. Same goes to side buttons, if u didnt wipe it down before curing it, you may as well say goodbye to your buttons..
@@xansieva27 thank so much!
If the glue gets into the volume keys and the earpiece would it get stuck and cause problems ?
I mean is this really safe for out very expensive devices?
my speaker is not working properly since liquid got in
@@gourab469 same💔💔
There is the strip sticker you should use to cover it with (he used it incorrectly in the video).
Such a long and fully technical name " Nano Optics Curved Edge To Edge Liquid UV Glue Tempered Glass for Samsung iPhone .."
It gives you a feeling that how advance your phone became by just applying a glass gaurd on it as it is ready to connect your galaxy handset directly with the aliens on mars.
Bc😂😂
You nailed it bro 😂👌🤣🤣
@@epicfear9264 thanks..🤣🤣
🤣🤣🤣🤣
😂😂😂😂😂😂😂😂😂
Okay so u have a tempered glass over your screen protector...lols for double protection 😂😂😂
Hi
Hope he does same after his marriage and dont produce multiple idiot like him again by using protection like the way he is using for mobile
yeah 🤣🤣🤣
Don't use this method with condom.
When you pull apart the old TG sometimes the bottom layer of film stays on the phone.
Good video👍📲
Thanks you bro😊
I just did mine in s galaxys7edge. GOOD ADVICE: cover with stickers all holes, buttons otherwise you will end up like me with needle trying to remove glue from underneath it ;-/ and some of them not working.
Cheers for the vid, had no clue what to do and 20 min later ive done 2 phones perfectly.
I would do that but am way to over protective with my phone lol
DREAD yt Isn’t that the point? To protect it.
@@cheesythegamer9771 no it's to use it. It's a toll ! Buy a new one in 2 years
Nobody:
My brain: ya ya yo yo ai ai
🤣👺🤣🤣🤣
What i wonder that, when the glass protector broke, can i remove the glass and use the UV glue as the screen scratch protector??? xD
No patrick
Believe me it will give you a headache when you want to remove this type of tempered glass
really
How often are you removing it? I've had the same protector on my phone for 6 years.
They are really quite easy to remove. The broken screen protector in the beginning of the video was the same type.
هعارغبغبعبتتبتيتبزب٨عقثغمقهبةي بعىا لخبىه٧٦٧٧٧٧٧٧٧٧٧٧٧٦٧٦٦٦٧
@@محمدكامل-ه6م كلام كبير يا معلم 👍🏼
you should have turned the screen on after screen guarding it
LOVE FROM BANGLADESH 🇧🇩🇧🇩🇧🇩👌👌
How it's look when you want to remove it? What the story with glue?
Glue will peel off clean
Its not glue . It is air bubble removing oil. After 2 days it will evaporates. But you should be careful on speakers and mic . While applying
Great video love it liquid Glass wowww I learn everyday 👍
Don't use it. because glue/gell can make speaker audio receiver and key side not working.
I got screwed with speaker
Be careful with the ear speaker front top part, if somehow the liquid gets stuck will block the tiny holes of the front ear speaker so as you won't listen anything!!!
Its IP68 proof so it will only be for 1 to 2 minute
After sawing thumbnail: looks like a very high technology, lets see
After watching video: for screen protector...
Ssd
I'm the only one jo toote huey phone se ye dekhra hai..😂🤦♂️
What about the speaker when the glue flows in there?
There is the strip sticker to cover it. He didnt use it correctly in the video tho. But its there.
This type of screen guard will hide scratches on mobile on main glass.. i liked it
Just a heads up guys Samsung Galaxy Note 10 Plus 5G.
You must tape up the earhole speaker, Power & Volume buttons on the side & the S-Pen Gap area near the bottom of the phone.
Why because the Liquid Glue Adhesive will seep leak into the Side Buttons & S-Pen causing it to harden and become permanently stuck meaning your whole phone is now fucked lol.
Just make sure absorb & dry any access liquid glue oozing out with a cloth or papper towel.
UV light at least 30sec to 60sec on top, middle & bottom & edge sides.
And Rescan your finger print scanner again afterwards and put sensitivity settings to on max 👍
@@itz_revotorq_dbswr All good mate this is the best method way of doing it for best results 👍
my god thank you so much. So glad I read this before applying mine!
Really, 6 million views and 7 million muting the sound.Thank you for the video.
2:55
Music name please 😍
Aradiginiz o remix
@@Wishy.boy. pleasure 😆👏
Chinese: 好！👍 Taiwanese: 好！👍
Is very good.
You must cover the loudspeaker from the beginning.
Otherwise the liquid will get into the loudspeaker
No , this is waterproof
@@amitsangwan9193 Yes I know, it's waterproof. I put too much liquid.
And now it's seen as a blanket on the loudspeaker near the Selfie camera.
4:04 the liquid wont go speaker ?
No it is ip68 rated
Ya but u can tape it as a precaution
It did. Not too deep though just enough to mess up your speaker specially after curing that glue
The background music is really irrigation
Use some pleasant instrument music like flute violin etc
Really superb installing the curved shaped glass for the Samsung mobile
🤣🤣Heard the child crying in background
This is more the video of how to not do it .. But anyway you made it! 😋
thank u
Would have liked to see it turned back on.
It never did
@@08jam08 thats funny
Thanks 👍👍👍
Edit:
Thank you again. Just installed mine and its perfect!
🕘🕓🕓🕑🕖🕖🕡🕖🕦🕚🕚🕥🕡🕞🕟🕣🕖🕡🕢🕓🕗🕡🕡📆
I can't find a tempered glass for MiA1 without bubble while applying🙄🤕
It had got scratched i think i mean ur phone
@@costa9645 no scratches in me. But I'm afraid of falling 🥴😂
@@ss-hj9rc 'll
Bhai ma laga deta ho
W.rtc w@@Hiteshpatel-lw2ir
Xcw
CD Washington kkklmu
Одно из адекватных видео о приклеивании стекла с УФ лампой. ОЧЕНЬ МНОГО ВИДЕО ОТ РУКОПОПОВ, будьте бдительны!
Опыт испорченных 2-3 стекол, хотя руки растут из плечей и голове толковой помогают Хочу дополнить, данное приклеивать лучше укладывая руками держа за 4 угла.
1.Клей открывается поворотом колпачка (срывается кончик вставленный в колпачек), не сохнет на открытом воздухе (есть время для манипуляций!).
2.Стики (наклейки) в комплекте после протирки спиртовой тканью отходят и становятся бесполезными для заклеивания динамика, кнопок (вкл./откл./регулятора громкости).
3.Клея в тубе больше, чем нужно, НО лучше вытечет, чем его будет недостаточно.
4. В момент укладки стекла на клей, можно, а чаще всего нужно разгонять его лёгким наклоном телефона! (АККУРАТНО - стекло плывет на клею).
5.Клей полимеризуется в течении 1-2 мин. при полном соприкосновении с лампой (проводил ОПЫТ с остатками клея!),превращается в что-то подобное клею-секунда. Автор правильно рекомендует пройти середину и после вытереть (АККУРАТНО - ТОЛЬКО ЗАДЕНЕШЬ КРАЙ, может попасть воздух, НО возможно подлить остатки клея и растянуть зубочисткой!) тряпочкой в комплекте (сухой!) или лучше салфеткой или туалетной бумагой насухо! Не проходить лампой пока не убедишься, что клей во всех возможных отверстиях телефона вытерт. В тот же момент не забываем, что стекло ПОДВИЖНО! - делаем предельно АККУРАТНО!
6.Напоследок хочу добавить, что телефон с выпирающей камерой не ложить на ровную поверхность, клей ОЧЕНЬ ТЕКУЧ и может просто сбежать с экрана! Некоторые продавцы комплектуют пластиковой рамкой для выравнивания стекла, считаю, что она относительно бесполезна (мой опыт!).
7.Приклевал ( держал/перемещал лампу на протяжении 7-10 мин. достаточно основательно). Итогом стало приклеенное стекло с 2 пузырьками на экране (НО посчитал ЛУЧШЕЕ-ВРАГ ХОРОШЕГО!;) и оставил! Надеюсь был вам полезен, желающий вам добра, Павел Никитин) Не снял, потому, что не было 2 камеры, делал долго и чуть ненормативной лексики...
Телефон с закругленными краями Xiaomi Mi Note 10 Pro.
a fluid used for gel manicures. And needs a uv light to cure it.
I think that fluid for gel manicures is very hard when is puted on display after uv. You have tryit?
Yes i have tried it's working fine
Thanks for answer
Thanks fir answer
Where can I buy the screen protector could u send me the link where u bought it from thank you
Stick no better than the cheap tempered glass protectors you find on eBay , gimmicky and expensive
Djebdhsbd
Bebehdbs
Bebeb
Cheaper actually only 5 to 6 dollars au.... no air bubbles and better protection
Who noticed of crying naby's sound from background ?😁😁
4:20 what a song
makes me soul
Upper wali platic remove krti i think...
I don't want to say this is wrong but I hope nobody is installing like this. When you drop the liquid, then drop the protector but do not press on the screen at all. Let the liquid flow by itself to the whole protector, it will never leak as long as you don't press it. Once all the glue spread, use the light a few seconds at a time around the screen. You'll never have any mess as long as you never press down.
This was extremely messy and probably wasted most of the liquid.
Muy mal así no se pone por que tiene el riesgo de que dañe los micrófonos y bocinas del celular
Smn
Cómo se aplica? Estoy pensando en comprarlo y me gustaría saber.
@@surelydelafuente6123
Vídeos
@@surelydelafuente6123 hcfecjuxtrxxhuyxdffwszghxnotdgewhbcegb cyhxcbvetyjvcfkjjvcddfhjbvffgkcdfhknbxfyhhcdrtukncgykgtjbtttttddvjjjjjjjjjjjjjcxeth njf
My cierto esto me parece pega llamada LOKA y la habia usado y me tapo el microfono pensé que se me daño el celular. Lo quite con un alfiler
MasterProRUclipsr man is here!
I am the only one who's phone don't have screen guys?
If your phone doesn't have a screen then how are you even watching this?
@@deutschelehrer69 Through the radio obviously
Wtf
i have a quesiton, does applying uv glue lessen the sensitivity of the screen? or its not reading the finger faster? or it improves the sensitivity? sorry my english is bad, i hope you understand and answer. pls thankyou
Fly come for the last minute 😂
is using that glue safe? especially on the earpiece and volume keys???
Definitely not...
Hi, thanks for the video.
I would like to know if when this protector with its liquid is removed to leave the screen without any kind of protector would there be any residue or mark on the screen?
Thank you.
Hola, gracias por el video.
Quisiera saber si cuando este protector con su liquido es extraido par dejar la pantalla sin ningun tipo de protector quedaria algun residuo o marca en la pantalla ?
Gracias.
I like how he liked your comment but didn't even reply. Smh.
It helps a lot. Please make video for how to cook rice
Yes pls
Yes
Yes
Yes
Yesss
Show 👏👏👏👏👏
Phali baaar kisi ye nhi kha mere chanal ko like kro aur maine like kiya
If one day if it gets cracked, does removal process damages the screen? does anybody tried?
I've been thru dat.. it doesnt affect the screen at all..
It doesn't damage your screen unless it is off I tried on Alcatel tablet when I removed it a sound came and I couldn't turn off it
Is hard to take it off ?
i got my curved display phone done by a professional.. is it meant to slowly create spaces at the edges? especially on the curved sides?😢
I do it everyday it's my skill 😂
ok
Bro is it easy to remove these kind of glasses..?
"Rihabe Arabic" The best channel for learning the Arabic language.
Question tho... How to remove the glue smell of the tempered glass?? Since I've done the messy way to do this :3 sometimes I could feel the stickiness of the glue whenever my hands gets sweaty
He didnt reply ur comment even though he love ur comment LOL
Al parecer (y por lo que pude entender en los comentarios), la segunda película que se saca del celular, es el pegamento
It was very helpful 🙂 thank you
yes , friend , we also can show you how to operate them 🥰🥰🥰
Watch out the buttons. If they get sticky glue in there and you cure it with UV, they don't work well. It happened to me
it's good friend
I m using it in my mate 20 pro its working fine
1 spilled glue on the side - finger pushing
2 touching lamp to protector
3 thus, glue ain't enough in your case
is it recommended to completely use the glue?
yeah better follow closely
be careful, first cover speaker and buttons with tape before applying product
I'm just here for the music.
Great video!
Greeting from Indonesian youtuber😋
Many thank bro
0:02 & 0:25 That sound's!
Hi, why did you have another film under the original broken tempered glass screen protector? Was it just an extra film protector for extra protection? Did it not reduce the sensitivity of the touch on phone?
هذا الشخص من ذاك ذاك التلفون ضيعه التلفون من اول وجديد
Thanks sir , for this tutorial.
ប្តូរអេក្រង់s10 5g តម្លៃប៉ុន្មាន?
It's so dirty do like this 🤩
Jangan like & subscribe
Please provide me a link to but the same exactly glass to buy online. I have tried somany glasses but nothing is fitting like this. This is a perfect glass for note 9.
U put two layers on this bi 😂😂💀💀
Where can i get such full coverage tempred glass for s9 plus ..?
All that i can find are having a wide notch at the top .
you can use any tempered glass you only need the the glue and the uv light
Aliexpress cmon its 2020 you should know this
Search "uv glass s9" 😅
But this glass is different. It covers fully edge to edge. I also need the same galss for my note 9
Sir my OnePlus 1 touch has broken
How can I contact with you
Plz sir repair my OnePlus 1 touch
So im trying to replace the back of my s10e but having an issue cause the replacement doesn't have that layer of glass on it. Any suggestions?
Go to a repair store lol
@@CutieRingoJoy omg i did lol like two different ones they really have no good answer but ty
Seu canal é tão bom que eu tô assistindo aqui do Brasil
I heard you like screenprotectors, so we put a screenprotector on top of your screenprotector.
I can only imagine how many people screwed their earspeaker because of ur lame video! Do not do anything unless u r sure u know how to do it correctly! This is the worst case scenario!
The liquid does not affect any port or the speakers. Get your head out of your ass and look up the product first.
@@DylanJSkittles i had to repair dozen of this way fd up speakers people brought to me! U should read the manual first than talk! Never apply pressure so that the liquid can escape!
@@DylanJSkittles it does not affect 🤮! When the speaker grill clogs with liquid u think sound comes out the same intensity as it used too! Think with ur brain!
@Reese M wiping doesnt help if the glue cures on the speaker grill! U had luck! But still i would bet one grand ur ear speaker is not the same volume intensity as it used to be! Liquid got into pores of 'ur grill!
@@karlosp02 anytime I have done this it has not affected anything. Before curing make sure you take a pin, lightly pick out anything that is in the speaker or ports, wipe clean with rubbing alcohol and then cure the screen. Good as new. Dont assume I dont know what the hell I'm talking about. Who knows if he edited this video, could have cropped out where he cleaned out ports.
6:46 is that a house fly on the top left
Just came to see how to change his tempered glass too lol
Is that a chopping board
This is the wrong method, they supposed to give you a case so it don’t drip from the sides
Oh hell no! This looks like a phone replacement waiting to happen. I’ll pass
I agree with you. I only use the ones that have the pre applied glue as you can take them off
Wow you are so stupid then as it comes off more easy than it takes to put it on and with no residues afterwards, but I guess the stupid love only the edges stuck down and wonder why those screen protectors are crappy!
@@fuherfrog7170 🐸 nice pic lol
I'm here to learn something, and my brain goes "ooh oh oh yeah yeah yeah, oh oh oh yeah yeah yeah"
I work for you, my loved ones of Christ,💖🌙
I think Whitestone dome glass is a little bit better because they give you materials
التعليق العربي إلى تدور عليه
هو ايه ده معلش غير الاسكرين
Are these type of protectors unable to crack? If they can crack what do you do then can this ever be removed?
How to remove this SP.. ? Worst technology this ?
I am using this UV glass on my samsung Galaxy Note 8 and Galaxy Note 9.Look perfect..I didn't yet try to take off yet..lol..still look perfect.
Look there's another video to how remove it , did u put it yourself ? I'm afraid of stick it though 🤦♂️
@@mostafamatar425 Yes i did put it myself but still in a perfect condition although i have drop twice.hehehe
@@WanHilarious oh wow how lucky u are, do u think that liquid is harmful for screen glass? As i'm afraid to harm my phone it's still new 🤦♂️🤣
@@mostafamatar425 This kind of stuff will not damage the screen because this screen are meant for the phone
Sir do you OnePlus 5 3D tempered glass!!
Sir do you english?
Where i can buy this glass guard ?
0:10 ASMR
The Uv temper glass how many days no attach on mobile screen plz tell me have this information sir plz 😔😔😔
How do you take it off
Man you guys love this video you guys are gonna love reading the fucking box instructions to this dump product. Even after I placed some stickers to block the glue to from getting into the speakers it somehow got in it hardened I can see it under light and after being so careful with it I got an air bubble 🤦♂️ you can’t fix the air bubble