Thank you CRANK for the great video. Here's what I heard from your video on torque specs. I added in/lb and ft/lb for your US viewers: Forward facing bottom nuts are 10NM (88 in/lb. 7.4 ft/lb) and bolts are 22NM (195 in/lb. 16 ft/lb). Main outside cups (50NM, 442.5 in/lb, 37 ft/lb) Reverse thread bolts are 8NM (71 in/lb. 6 ft/lb). Rear VANOS bolts 10NM (88 in/lb. 7.4 ft/lb)
Una cosa que no hice fue quitar ese cilindro hidraulico.en cuanto pueda tendre que cambiarlo.ese cilindro es para todo el circuito o es solo para la admision y el otro cilindro es para el escape?
I’ve certainly enjoyed the rebuild walk through. Thanks for sharing this. A question, however; shouldn’t you use petroleum jelly or light coating of motor oil during the Vanos rebuild? Oil and silicone spray don’t mix.
Thanks! About the silicone, there are a lot of oils which are containing silicones in them, a lot of OEM oils. So I highly doubt it will cause any issue. But yeah, if you use assembly lube or any type of engine oil, will still do the job done.
very helpful video. done everything like you showed, but when putted all back together rattle noise is still there :( . any ideas what I've done wrong??? Help please
Hey. very cool technical video on engine rebuild . I am interested whats is your calculated static Compression ratio and dynamic compression ratio.? And what fuel are you planing to use ? and offcurese what power figer you are aiming to ?
The engine is going to run the stock CP 10,2:1 with stock cams, so the DCR is going to be pretty much stock. The only performance ( increasing HP ) part installed in this series, is the cylinder head, which is ported. This will lead probably something around of +20 hp region. After some time, the owner will decide if he going to install the G Power compressor kit, which he bought
hello there..i got e46 325i I'm having a problem : vanos exhaust side end position not reached. when i scan using bmw scanner 1.4 I thought because of the bad O ring vanos then I decided to buy a vanos O ring kit and do the vanos job. then i did a reset timing by a bmw specialist repair shop at my location. Previously I also found that my exhaust vanos oil gate was stuck and I cleaned it when I tested it can move freely again. the first time I disassembled the vanos there was no oil pressure in the exhaust vanos but after I cleaned the oilgate and I disassembled the vanos for the 2nd time there was oil pressure in the exhaust vanos. but now i'm still having this problem. Can this be caused by a labored ex cam sensor? I'm stuck with this problem thanks in advance
How important is replacing the o-rings on the plastic caps? I rebuilt my VANOS recently and couldn't get those caps all the way in with the new o-rings (like you at 38:15), so I just used the old caps (with old o-rings). Is it worth taking the valve cover off again and try to replace these plugs with new o-rings?
@@crank3646 low-end torque seems good to me so I think I'll leave it until next time I need to take off the valve cover or if I'm really bored. Thanks man, love your videos!
Здравей! На М54Б22 имам проблем със студения старт,с играещи обороти, педала на газта преди да загрее реагира бавно, в ниските обороти колата не набира като за 170коня. Смених свещи, бобини, картерна вентилация, ламбда сонди, горивен филтър, почистих дюзи, но проблема е на лице все още. Остана само реновиране на ваносите според мен, дали е това? Има ли вариант да се чуем да обясня по подробно, да ми дадеш някой съвет? Просто вече останах без нерви. Благодаря предварително!
@@crank3646 You devote many hours to produce a good video for entertaining and learning , and you did ask the question so l answered you..And it's my pleasure mate...Keep them coming!!
Very nice for guys who want to do this by a DIY. Thanks for sharing. Dutch regards, Nico.
Thanks Nico !
As always, excellent video! Just got a beisan kit for my B30, this helps immensely! Thank you so much!
Thanks !
good teaching video , always interesting to watch the Crank
Very good video loud and clear with patience explanation👌👌👍👍
Again, very well done. Regards
Thank you for another good video!!!
Thanks nemanja !
Is there a VANOS rebuild kit? Or do you have to purchase replacements sepaeateyl?
Thank you CRANK for the great video. Here's what I heard from your video on torque specs. I added in/lb and ft/lb for your US viewers:
Forward facing bottom nuts are 10NM (88 in/lb. 7.4 ft/lb) and bolts are 22NM (195 in/lb. 16 ft/lb).
Main outside cups (50NM, 442.5 in/lb, 37 ft/lb)
Reverse thread bolts are 8NM (71 in/lb. 6 ft/lb).
Rear VANOS bolts 10NM (88 in/lb. 7.4 ft/lb)
I like the way u explain
Una cosa que no hice fue quitar ese cilindro hidraulico.en cuanto pueda tendre que cambiarlo.ese cilindro es para todo el circuito o es solo para la admision y el otro cilindro es para el escape?
Ayni bu sekil soktum tamir takimi yeniledim m52tu altdevirler super oldu
I’ve certainly enjoyed the rebuild walk through. Thanks for sharing this. A question, however; shouldn’t you use petroleum jelly or light coating of motor oil during the Vanos rebuild? Oil and silicone spray don’t mix.
Thanks! About the silicone, there are a lot of oils which are containing silicones in them, a lot of OEM oils. So I highly doubt it will cause any issue. But yeah, if you use assembly lube or any type of engine oil, will still do the job done.
very helpful video. done everything like you showed, but when putted all back together rattle noise is still there :( . any ideas what I've done wrong??? Help please
Hey. very cool technical video on engine rebuild . I am interested whats is your calculated static Compression ratio and dynamic compression ratio.?
And what fuel are you planing to use ?
and offcurese what power figer you are aiming to ?
The engine is going to run the stock CP 10,2:1 with stock cams, so the DCR is going to be pretty much stock. The only performance ( increasing HP ) part installed in this series, is the cylinder head, which is ported. This will lead probably something around of +20 hp region. After some time, the owner will decide if he going to install the G Power compressor kit, which he bought
No timing tool needing?
hello there..i got e46 325i
I'm having a problem : vanos exhaust side end position not reached. when i scan using bmw scanner 1.4
I thought because of the bad O ring vanos then I decided to buy a vanos O ring kit and do the vanos job. then i did a reset timing by a bmw specialist repair shop at my location. Previously I also found that my exhaust vanos oil gate was stuck and I cleaned it when I tested it can move freely again. the first time I disassembled the vanos there was no oil pressure in the exhaust vanos but after I cleaned the oilgate and I disassembled the vanos for the 2nd time there was oil pressure in the exhaust vanos.
but now i'm still having this problem. Can this be caused by a labored ex cam sensor? I'm stuck with this problem
thanks in advance
How important is replacing the o-rings on the plastic caps? I rebuilt my VANOS recently and couldn't get those caps all the way in with the new o-rings (like you at 38:15), so I just used the old caps (with old o-rings). Is it worth taking the valve cover off again and try to replace these plugs with new o-rings?
You can lose some oil pressure in the vanos units, which can lead to bad operation, it is up to you to decide.
@@crank3646 low-end torque seems good to me so I think I'll leave it until next time I need to take off the valve cover or if I'm really bored. Thanks man, love your videos!
Hi, I would like to ask what kit (brand) was used for refurbishment? Thank you very much for the information🙂
X8R from UK
@@crank3646 thansk :)
Здравей! На М54Б22 имам проблем със студения старт,с играещи обороти, педала на газта преди да загрее реагира бавно, в ниските обороти колата не набира като за 170коня. Смених свещи, бобини, картерна вентилация, ламбда сонди, горивен филтър, почистих дюзи, но проблема е на лице все още. Остана само реновиране на ваносите според мен, дали е това? Има ли вариант да се чуем да обясня по подробно, да ми дадеш някой съвет? Просто вече останах без нерви. Благодаря предварително!
👍😎
Mate are u in uk?
Bratlee evalata za klipovete ama day malko i za dizelite na bmw 😁 m47/57 ili sushto N47/57
CAn you make traduction arab . 7:24
Subtitulos please
Къде се намираш и правиш ли пълен ребилд за клиенти?
Здравейте! Намираме се в Бургас. Като цяло повечето видеа са на клиентски коли, така че да :)
Браво няма ли да ремонтираме някоя Ф30-ка
Те новите БМВ-та не се чупят
..o
Shim is correct english......jus lie dat ..hahahaha
You are always there to correct my spelling :D
@@crank3646 You devote many hours to produce a good video for entertaining and learning , and you did ask the question so l answered you..And it's my pleasure mate...Keep them coming!!